Implementation of software load support for the BE iommu. This is very
different from other iommu code on ppc64, since we only do a static mapping.
The mapping is currently hardcoded but should really be read from the
firmware, but they don't set up the device nodes yet. There is a single
512MB DMA window for PCI, USB and ethernet at 0x20000000 for our RAM.

The Cell processor can put the I/O page table either in memory like
the hashed page table (hardware load) or have the operating system
write the entries into memory mapped CPU registers (software load).

I use the software load mechanism because I know that all I/O page
table entries for the amount of installed physical memory fit into
the IO TLB cache. At the point when we get machines with more than
4GB of installed memory, we can either use hardware I/O page table
access like the other platforms do or dynamically update the I/O
TLB entries when a page fault occurs in the I/O subsystem.

The software load can then use the macros that I have implemented
for the static mapping in order to do the TLB cache updates.
Signed-off-by: NArnd Bergmann <arndb@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Add support for the integrated interrupt controller on BPA
CPUs. There is one of those for each SMT thread.

The mapping of interrupt numbers to HW interrupt sources
is described in arch/ppc64/kernel/bpa_iic.h.

This version hardcodes the 'Spider' chip as the secondary
interrupt controller. That is not really generic for the
architecture, but at the moment it is the only secondary
PIC that exists.

A little more work will be needed on this as soon as
we have boards with multiple external interrupt controllers.
Signed-off-by: NArnd Bergmann <arndb@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This adds the basic support for running on BPA machines.
So far, this is only the IBM workstation, and it will
not run on others without a little more generalization.

It should be possible to configure a kernel for any
combination of CONFIG_PPC_BPA with any of the other
multiplatform targets.
Signed-off-by: NArnd Bergmann <arndb@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

BPA is using rtas for PCI but should not be confused by
pSeries code. This also avoids some #ifdefs. Other
platforms that want to use rtas_pci.c could create
their own platform_pci.c with platform specific fixups.
Signed-off-by: NArnd Bergmann <arndb@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This patch allows iSeries to build with CONFIG_PCI=n.  This is useful for
partitions that have only virtual I/O.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch just merges XmPciLpEvent.c into iSeries_irq.c (the only caller of
its only external function).  XmPciLpEvent.c just contained the lowlevel
iSeries irq code.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Clean up iSeries_VpdInfo.c:
	- white space and comment fixes
	- make a function static
	- the functions here are only called from iSeries_pci.c, so
	  CONFIG_PCI will be set (so remove check)
	- only build when CONFIG_PCI is set
	- remove unneeded includes and cast
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The file arch/ppc64/kernel/iSeries_pci_reset contains only one function that
is not use anywhere (any more).  Remove it.  This function is the only user of
the ReturnCode member of iSeries_Device_Node, so remove that as well.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!