Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use a string to specific the wakeup mode to make it more readable.

Add the Real-time Clock Wake-up support too for sam9g45 and sam9x5.
Add AT91_SHDW_CPTWK0_MAX to specific the Max of the Wakeup Counter.
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NRob Herring <rob.herring@calxeda.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>

We can now drop the call to ioremap_registers() as we have the binding for the
SDRAM/DDR Controller.

Drop ioremap_registers() for sam9x5 too.
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NRob Herring <rob.herring@calxeda.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NRob Herring <rob.herring@calxeda.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>

This is need for multiple SoC in the same kernel image and DT.
As we will chose the restart function via binding.
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NRob Herring <rob.herring@calxeda.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Specified the main Oscillator via clock binding.
This will allow to do not hardcode it anymore in the DT board at 12MHz.
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NRob Herring <rob.herring@calxeda.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>

This will allow to have static Device mapping and DT probe mapping for the
System Controller.

Temporary keep the call to ioremap_registers() until we have the binding
for the SDRAM/DDR Controller.

Temporary keep the main clock hardcoded to 12MHz until we have the binding
for the PMC.
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NRob Herring <rob.herring@calxeda.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>

http://www.calao-systems.com/articles.php?lng=en&pg=6099

this daughter board add the following device:
 - Micro-SD socket
 - TTL 3V3 - (Tx/Rx/RTS/CTS)
 - I2C port
 - 0.96" Serial OLED Display Module (over UART)
 - MP3 decoder with Micro & Speakers
 - 4x PB, 4x Leds (Blue), 3x Leds (Green, Orange, Red)

for now we add only the 2 UARTs, 4 Buttons, 7 leds and i2c via DT

used_led1 will not be re-add via DT as it's used by the motherboard too
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

For now on use i2c-gpio driver on the same pin as the hardware IP.
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NRob Herring <rob.herring@calxeda.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>

For now on use i2c-gpio driver on the same pin as the hardware IP.
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NRob Herring <rob.herring@calxeda.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>

Use i2c-gpio and enable rv3029 RTC.

Enable the rtc in the sam9g20 defconfig.
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NRob Herring <rob.herring@calxeda.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>

For now on use i2c-gpio driver on the same pin as the hardware IP.
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NRob Herring <rob.herring@calxeda.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>

To achieve DT support, we need to populate a custom platform_data in a
private struct from DT information. To simplify code, the adapter and
algorithm are also put into the private struct.
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NRob Herring <rob.herring@calxeda.com>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>

Enable the nand in the cpu module with the partition.
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Use a local copy of board informatin and fill with DT data.
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>

- nand-ecc-mode : String, operation mode of the NAND ecc mode.
  Supported values are: "none", "soft", "hw", "hw_syndrome", "hw_oob_first",
  "soft_bch".
- nand-bus-width : 8 or 16 bus width if not present 8
- nand-on-flash-bbt: boolean to enable on flash bbt option if not present false
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NStefan Roese <sr@denx.de>

of_property_read_bool

Search for a property in a device node.
Returns true if the property exist false otherwise.
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NRob Herring <rob.herring@calxeda.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>

Enable it on Calao board too as they are in DT too.
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

This will allow to enable it from the board.
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NDavid Woodhouse <dwmw2@infradead.org>

So we can now choose for the board the ecc mode (ecc soft, soft bch, no ecc
and hardware).

Set ecc mode in the boards to soft as currently in the driver.

Move platform data to a common header
include/linux/platform_data/atmel_nand.h
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NHans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: NDavid Woodhouse <dwmw2@infradead.org>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Use the gpio for d7 as we do not support yet the pwm led via dt.
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>

This patch adds the support for new PIO controller found on some
at91sam SOCs.
- more peripheral multiplexing
- more features to configure on a PIO (pull-down, Schmitt trigger, debouncer)
- support for several IRQ triggering features (type and polarity)

Support for those new features are retrieved from the device tree
compatibility string.

Debugfs at91_gpio file is updated to monitor configuration.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add these SMC accessors to the at91sam9x5 as we will need them for
NAND flash (for instance).
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Some SoC have a 32 bit variant of Timer Counter Blocks. We do not
need the chaining of two 16 bit counters anymore for them.

The SoC nature is deduced from the device tree "compatible" string.
For non-device-tree configurations, backward compatibility is maintained
by using the default 16 bit counter configuration.

This patch addresses both the atmel_tclib and its user: tcb_clksrc
clocksource.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>

Device tree support added to atmel_tclib: the generic Timer Counter
library. This is used by the clocksource/clockevent driver tcb_clksrc.

The current DT enabled platforms are also modified to use it:
- .dtsi files are modified to add Timer Counter Block entries
- alias are created to allow identification of each block
- clkdev lookup tables are added for clocks identification.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>

Requesting iomem region and ioremaping is now done using
the resource size specified instead of a constant value.

Each <SoC>_device.c file is modified accordingly to reflect
actual user interface size.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Traces related to IRQ management are useful for timers in case of
non-working IRQ subsystem (switch to irq_domain for instance).
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Retreive registers address and IRQ from device tree entry.
Called from at91_dt_init_irq() so that timers are up-n-running
when timers initialization will occur.
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
[nicolas.ferre@atmel.com: change error path and interrupts property handling]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Both AIC and GPIO controllers are now using the standard of_irq_init()
function to initialize IRQs in case of DT use.
The DT specific initialization functions are now separated from the
non-DT case and are now using "linear" irq domains.
The .map() irqdomain operation is responsible for positioning the IRQ
handlers. In AIC case, the Linux IRQ number is directly programmed in
the hardware to avoid an additional reverse mapping operation.
The AIC position its irq domain as the "default" irq domain.

For DT case, the priority is not yet filled in the SMR. It will be the
subject of another patch.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Adding of irqdomain in AIC code make the specification
of the irq domain in board file useless.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

This value is determined at runtime using device tree or platform data
information.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Replace the gpio_to_irq() macro by a plain gpiolib .to_irq() handler.
This call is using the irqdomain to translate hardware to Linux
IRQ numbers.
The irq_to_gpio() macro is completely removed.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Protect build failure in case of non-DT configuration: the
gpio_chip structure does not have a of_node field in case of
!CONFIG_OF_GPIO.

Keep this in a separate patch as it can be reverted if the
field is added for both DT/non-DT cases.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Add "legacy" type of irqdomain to preserve old-style numbering
and allow smooth transition for both DT and non-DT cases.

Original idea and code by Jean-Christophe Plagniol-Villard.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

What was true only on at91sam9263 about the sharing of a single AIC
IRQ line for several GPIO banks is now used by several Atmel SoCs.

Change a variable name to allow better understanding while
introducing IRQ domains in following patches.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

irq_to_gpio() macro will be removed from AT91 GPIO interrupt
controller. So we replace it with the use of gpio_to_irq()
and a reworked test.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: linux-usb@vger.kernel.org