Signed-off-by: NBryan O'Sullivan <bos@pathscale.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Some systems do not set up 64-bit maps on systems with 2GB or less of
memory installed, so we have to fall back to trying a 32-bit setup.
Signed-off-by: NBryan O'Sullivan <bos@pathscale.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

We were accidentally exposing the "reset" sysfs file more than once
per device.
Signed-off-by: NBryan O'Sullivan <bos@pathscale.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

GuidInfo records have 8 byte GUIDs in them, so an index should be
multiplied by 8 to get an offset.  mthca_query_gid() was incorrectly
multiplying by 16.

Noticed by Leonid Keller <leonid@mellanox.co.il>.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Update version to 3.57.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix bug in nvram write function. If the starting nvram address offset
happens to be the last dword of the page, the NVRAM_CMD_LAST bit will
not get set in the existing code. This patch fixes the bug by changing
the "else if" to "if" so that the last dword condition always gets
checked.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a reset_phy parameter to tg3_reset_hw() and tg3_init_hw(). With
the full chip reset during MAC address change, the automatic PHY reset
during chip reset will cause a link down and bonding will not work
properly as a result. With this reset_phy parameter, we can do a chip
reset without link down when changing MAC address or MTU.
Signed-off-by: NGary Zambrano <zambrano@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Do the full chip reset when changing MAC address if ASF is enabled.

ASF sometimes uses a different MAC address than the driver. Without
the reset, the ASF MAC address may be overwritten when the driver's
MAC address is changed.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add some PHY workaround code to reduce jitter on some PHYs.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add netif_carrier_off() call during tg3_phy_reset(). This is needed
to properly track the netif_carrier state in cases where we do a
PHY reset with interrupts disabled. The SerDes code will not run
properly if the netif_carrier state is wrong.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Content of file au1200fb.c was duplicated. Remove.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NAntonino Daplas <adaplas@pol.net>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Let people enable the advansys driver on x86-32, even though it's broken
on other architectures due to missing DMA mapping infrastructure.

It's used by Jeffrey Phillips Freeman <jeffreyfreeman@syncleus.com> and
possibly others.
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

While writing to an event device allows to set repeat rate for an
individual input device there is no way to retrieve current settings
so we need to ressurect EVIOCGREP. Also ressurect EVIOCSREP so we
have a symmetrical interface.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Add help text in Kconfig
Signed-off-by: NAntonino Daplas <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Generate new sysfs-attribute 'uid' that contains an device specific unique
identifier.  This can be used to identity multiple ALIASES of the same
physical device (PAV).  In addition the sysfs-attributes 'vendor' (containing
the manufacturer of the device) and 'alias' (identify alias or base device) is
added.  This is first part of PAV support in LPAR (also valid on zVM).
Signed-off-by: NHorst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

In case of an instruction processing damage (IPD) machine check in kernel mode
the resulting action is always to stop the kernel.  This is not necessarily
the best solution since a retry of the failing instruction might succeed.  Add
logic to retry the instruction if no more than 30 instruction processing
damage checks occured in the last 5 minutes.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Added some changes that where proposed by Andrew Morton.  Added 3592 device
type.
Signed-off-by: NStefan Bader <shbader@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

With CONFIG_SLAB_DEBUG=y networking over qeth doesn't work.  The problem is
that the qib structure embedded in the qeth_irq structure needs an alignment
of 256 but kmalloc only guarantees an alignment of 8.  When using SLAB
debugging the alignment of qeth_irq is not sufficient for the embedded qib
structure which causes all users of qdio (qeth and zfcp) to stop working.
Allocate qeth_irq structure with __get_free_page.  That wastes a small amount
of memory (~2500 bytes) per online adapter.
Signed-off-by: NChristian Borntraeger <cborntra@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The dasd state machine is not designed to enable an unformatted device, since
'unformatted' is a final state.  The BIODASDENABLE ioctl calls
dasd_enable_device() which never returns if the device is in this special
state.  Return -EPERM in dasd_increase_state for unformatted devices to make
dasd_enable_device terminate.  Note: To get such an unformatted device online
it has to be re-analyzed.  This means that the device needs to be disabled
prior to re-enablement.
Signed-off-by: NHorst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Avoid memory allocation with GFP_KERNEL in qdio_establish/qdio_shutdown.  Use
memory pool instead.  (Otherwise this can lead to an I/O stall where qdio
waits for a free page and zfcp waits for end of error recovery in low memory
situations.)
Signed-off-by: NAndreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Interrupts can stay disabled if an error occurred in _chp_add().  Use
spin_unlock_irq on the error paths to reenable interrupts.
Signed-off-by: NStefan Bader <shbader@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fix a race condition in the I/O termination logic.  The race can cause I/O to
a dasd device to fail with no retry left after turning one channel path to the
device off and on multiple times.
Signed-off-by: NPeter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

this fixes coverity id #489.

Since the last element in the array is always ARRAY_SIZE-1 we have to check
for ipcnum >= ARRAY_SIZE()
Signed-off-by: NEric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

If compiled into the kernel, parport_register_driver() is called before the
parport driver has been initalised.

This means that it is expected that tp_count is 0 after the
parport_register_driver() call() - tipar's attach function will not be
called until later during bootup.
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

- Add new SA_PROBEIRQ which suppresses the new sharing-mismatch warning.
  Some drivers like to use request_irq() to find an unused interrupt slot.

- Use it in i82365.c

- Kill unused SA_PROBE.
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Current address translation methods can produce wrong results, because
virt_to_bus and vice versa may not produce correct offsets on dma-allocated
memory. The right way is, while tracking both phys and virt address of the
window that has been allocated for boffer descriptors, and use those
numbers to compute the offset and make translation properly.
Signed-off-by: NVitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This is intended to make the driver code more generic and flexible,
to get rid of board-specific layouts within driver, and generic rehaul,
yet keeping compatibility with the existing stuff utilizing it, being
compatible with legacy behavior (but with complaints that legacy mode
used).
Signed-off-by: NVitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Some people report that we die on some Macs when we are expecting to
catch machine checks after poking at some random I/O address. I'd seen
it happen on my dual G4 with serial ports until we fixed those to use
OF, but now other users are reporting it with i8042.

This expands the use of check_legacy_ioport() to avoid that situation
even on 32-bit kernels.
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Remove it as it does not work properly due to sysfs core changes.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Alan Cox pointed out that the VIA 'IRQ fixup' was erroneously running
on my system which has no VIA southbridge (but I do have a VIA IEEE
1394 device).

This should address that.  I also changed "Via IRQ" to "VIA IRQ"
(initially I read Via as a capitalized via (by way/means of).
Signed-off-by: NChris Wedgwood <cw@f00f.org>
Acked-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The coverity checker spotted (as entry #599) that we might leak `entry' in
drivers/pci/msi.c::msix_capability_init()
This patch should take care of that.
Signed-off-by: NJesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NHenrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch adds support for an ASK RDR 400 series contactless card
reader <http://www.ask.fr/uk/products_and_services/terminals.html> to
the ftdi_sio driver's device ID table.  The product ID was supplied by
Adriano Couto on the ftdi-usb-sio-devel list.
Signed-off-by: NIan Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Adds support in ftdi_sio usbserial driver for USB modems sold by
Plus GSM Company in Poland.
Signed-off-by: NLuiz Fernando Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds recognition of the RR-CirKits LocoBuffer USB
to the existing FTDI driver.  http://www.rr-cirkits.comSigned-off-by: NNathan Bronson <ngb@sns-usa.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

We could use the recently added PCI_CLASS_SERIAL_USB_UHCI,
PCI_CLASS_SERIAL_USB_OHCI and PCI_CLASS_SERIAL_USB_EHCI defines in
more places, for slightly shorter and clearer code.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as671) fixes a bug in the error pathway for the net2280
probe routine.  A failure during probe will cause the driver to call
pci_get_drvdata before the corresponding pci_set_drvdata has been set.
The patch also does a kzalloc conversion.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as670) adds a check for whether a shared IRQ was actually
generated by the net2280 device.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>