To use boot tracer, one should pass initcall_debug as well as
ftrace=initcall to the command line.
Signed-off-by: NLi Zefan <lizf@cn.fujitsu.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
LKML-Reference: <4A48735E.9050002@cn.fujitsu.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Some fields for struct ftrace_graph_ret are missed
when they are exported to user.
Signed-off-by: NLai Jiangshan <laijs@cn.fujitsu.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
LKML-Reference: <4A448FB6.5000302@cn.fujitsu.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

This made my machine completely frozen:

  # echo 1 > /proc/sys/kernel/stack_tracer_enabled
  # echo 2 > /proc/sys/kernel/stack_tracer_enabled

The cause is register_ftrace_function() was called twice.

Also fix ftrace_enabled sysctl, though seems nothing bad happened
as I tested it.
Signed-off-by: NLi Zefan <lizf@cn.fujitsu.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <4A448D17.9010305@cn.fujitsu.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

The first entry of the ftrace profile was always skipped when
reading trace_stat/functionX.
Signed-off-by: NLi Zefan <lizf@cn.fujitsu.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <4A443D59.4080307@cn.fujitsu.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

In hunting down the cause for the hwlat_detector ring buffer spew in
my failed -next builds it became obvious that folks are now treating
ring_buffer as something that is generic independent of tracing and thus,
suitable for public driver consumption.

Given that there are only a few minor areas in ring_buffer that have any
reliance on CONFIG_TRACING or CONFIG_FUNCTION_TRACER, provide stubs for
those and make it generally available.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
Cc: Jon Masters <jcm@jonmasters.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
LKML-Reference: <20090625053012.GB19944@linux-sh.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Before:
  # echo 'sys_open:traceon:' > set_ftrace_filter
  # echo 'sys_close:traceoff:5' > set_ftrace_filter
  # cat set_ftrace_filter
  #### all functions enabled ####
  sys_open:traceon:unlimited

  sys_close:traceoff:count=0

After:
  # cat set_ftrace_filter
  #### all functions enabled ####
  sys_open:traceon:unlimited
  sys_close:traceoff:count=0
Signed-off-by: NLi Zefan <lizf@cn.fujitsu.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <4A4313A7.7030105@cn.fujitsu.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

We should be able to specify [KMG] when setting trace_buf_size
boot option, as documented in kernel-parameters.txt
Signed-off-by: NLi Zefan <lizf@cn.fujitsu.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <4A41F2DB.4020102@cn.fujitsu.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

When the output of set_ftrace_filter is larger than PAGE_SIZE,
t_hash_start() will be called the 2nd time, and then we start
from the head of a hlist, which is wrong and causes some entries
to be outputed twice.

The worse is, if the hlist is large enough, reading set_ftrace_filter
won't stop but in a dead loop.
Reviewed-by: NLiming Wang <liming.wang@windriver.com>
Signed-off-by: NLi Zefan <lizf@cn.fujitsu.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <4A41876E.2060407@cn.fujitsu.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

It's rather confusing that in t_start(), in some cases @pos is
incremented, and in some cases it's decremented and then incremented.

This patch rewrites t_start() in a much more general way.

Thus we fix a bug that if ftrace_filtered == 1, functions have tracer
hooks won't be printed, because the branch is always unreachable:

static void *t_start(...)
{
	...
	if (!p)
		return t_hash_start(m, pos);
	return p;
}

Before:
  # echo 'sys_open' > /mnt/tracing/set_ftrace_filter
  # echo 'sys_write:traceon:4' >> /mnt/tracing/set_ftrace_filter
  sys_open

After:
  # echo 'sys_open' > /mnt/tracing/set_ftrace_filter
  # echo 'sys_write:traceon:4' >> /mnt/tracing/set_ftrace_filter
  sys_open
  sys_write:traceon:count=4
Reviewed-by: NLiming Wang <liming.wang@windriver.com>
Signed-off-by: NLi Zefan <lizf@cn.fujitsu.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <4A41874B.4090507@cn.fujitsu.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

It's wrong to increment @pos in g_start(). It causes some entries
lost when reading set_graph_function, if the output of the file
is larger than PAGE_SIZE.
Reviewed-by: NLiming Wang <liming.wang@windriver.com>
Signed-off-by: NLi Zefan <lizf@cn.fujitsu.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <4A418738.7090401@cn.fujitsu.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

The iterator is m->private, but it's not reset to trace_types in
t_start(). If the output is larger than PAGE_SIZE and t_start()
is called the 2nd time, things will go wrong.
Reviewed-by: NLiming Wang <liming.wang@windriver.com>
Signed-off-by: NLi Zefan <lizf@cn.fujitsu.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <4A418728.5020506@cn.fujitsu.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

It's wrong to increment @pos in stat_seq_start(). It causes some
stat entries lost when reading stat file, if the output of the file
is larger than PAGE_SIZE.
Reviewed-by: NLiming Wang <liming.wang@windriver.com>
Signed-off-by: NLi Zefan <lizf@cn.fujitsu.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <4A418716.90209@cn.fujitsu.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

It's wrong to increment @pos in t_start(), otherwise we'll lose
some entries when reading printk_formats, if the output is larger
than PAGE_SIZE.
Reported-by: NLai Jiangshan <laijs@cn.fujitsu.com>
Reviewed-by: NLiming Wang <liming.wang@windriver.com>
Signed-off-by: NLi Zefan <lizf@cn.fujitsu.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <4A4186FA.1020106@cn.fujitsu.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

While testing syscall tracepoints posted by Jason, I found 3 entries
were missing when reading available_events. The output size of
available_events is < 4 pages, which means we lost 1 entry per page.

The cause is, it's wrong to increment @pos in s_start().

Actually there's another bug here -- reading avaiable_events/set_events
can race with module unload:

  # cat available_events               |
      s_start()                        |
      s_stop()                         |
                                       | # rmmod foo.ko
      s_start()                        |
        call = list_entry(m->private)  |

@call might be freed and accessing it will lead to crash.
Reviewed-by: NLiming Wang <liming.wang@windriver.com>
Signed-off-by: NLi Zefan <lizf@cn.fujitsu.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <4A4186DD.6090405@cn.fujitsu.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

On bootup nvidiafb prints the following on my Apple G5:

	nvidiafb: CRTC 1appears to have a CRT attached

There should be a space between the '1' and the 'appears'.  Add it.
Signed-off-by: NMikael Pettersson <mikpe@it.uu.se>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix the incorrect "select" directives by dropping the "CONFIG_"
prefixes, and correcting the typo "H8S2768" to "H8S2678".
Signed-off-by: NRobert P. J. Day <rpjday@crashcourse.ca>
Acked-by: NYoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

After downing/upping a cpu, an attempt to set
/proc/sys/vm/percpu_pagelist_fraction results in an oops in
percpu_pagelist_fraction_sysctl_handler().

If a processor is downed then we need to set the pageset pointer back to
the boot pageset.

Updates of the high water marks should not access pagesets of unpopulated
zones (those pointer go to the boot pagesets which would be no longer
functional if their size would be increased beyond zero).
Signed-off-by: NDimitri Sivanich <sivanich@sgi.com>
Signed-off-by: NChristoph Lameter <cl@linux-foundation.org>
Reviewed-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

After the recent changes that went into mm/vmscan.c to overhaul stuff, we
ended up with these warnings on no-mmu systems:

  mm/vmscan.c: In function `shrink_page_list':
  mm/vmscan.c:580: warning: unused variable `vm_flags'
  mm/vmscan.c: In function `shrink_active_list':
  mm/vmscan.c:1294: warning: `vm_flags' may be used uninitialized in this function
  mm/vmscan.c:1242: note: `vm_flags' was declared here

This is because the no-mmu function defines page_referenced() to work on
the first argument only (the page).  It does not clear the vm_flags given
to it because for no-mmu systems, they never actually get utilized.  Since
that is no longer strictly true, we need to set vm_flags to 0 like
everyone else so gcc can do proper dead code elimination without annoying
us with unused warnings.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Cc: David Howells <dhowells@redhat.com>
Acked-by: NDavid McCullough <davidm@snapgear.com>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If a kthread happens to use get_user_pages() on an mm (as KSM does),
there's a chance that it will end up trying to read in a swap page, then
oops in grab_swap_token() because the kthread has no mm: GUP passes down
the right mm, so grab_swap_token() ought to be using it.

We have not identified a stronger case than KSM's daemon (not yet in
mainline), but the issue must have come up before, since RHEL has included
a fix for this for years (though a different fix, they just back out of
grab_swap_token if current->mm is unset: which is what we first proposed,
but using the right mm here seems more correct).
Reported-by: NIzik Eidus <ieidus@redhat.com>
Signed-off-by: NJohannes Weiner <hannes@cmpxchg.org>
Signed-off-by: NHugh Dickins <hugh.dickins@tiscali.co.uk>
Acked-by: NRik van Riel <riel@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
  sh: Fix up HAVE_PERF_COUNTERS typo.
  sh: Fix up more dma-mapping fallout.
  sh: SH7786 SMP support.
  sh: Wire up the uncached fixmap on sh64 as well.
  sh: Use local TLB flush in set_pte_phys().
  sh: Provide cpu_idle_wait() to fix up cpuidle/SMP build.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  RDMA: Add __init/__exit macros to addr.c and cma.c
  IB/ehca: Bump version number
  mlx4_core: Fix dma_sync_single_for_cpu() with matching for_device() calls
  IB/mthca: Replace dma_sync_single() use with proper functions
  RDMA/nes: Fix FIN state handling under error conditions
  RDMA/nes: Fix max_qp_init_rd_atom returned from query device
  IB/ehca: Ensure that guid_entry index is not negative
  IB/ehca: Tolerate dynamic memory operations before driver load

* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (38 commits)
  fusion: mptsas, fix lock imbalance
  [SCSI] scsi_transport_fc: replace BUS_ID_SIZE by fixed count
  sd, sr: fix Driver 'sd' needs updating message
  scsi_transport_iscsi: return -EOVERFLOW for Too many iscsi targets
  fc_transport: Selective return value from BSG timeout function
  fc_transport: The softirq_done function registration for BSG request
  sym53c8xx: ratelimit parity errors
  explain the hidden scsi_wait_scan Kconfig variable
  ibmvfc: Fix endless PRLI loop in discovery
  ibmvfc: Process async events before command responses
  libfc: Add runtime debugging with debug_logging module parameter
  libfcoe: Add runtime debugging with module param debug_logging
  fcoe: Add runtime debug logging with module parameter debug_logging
  scsi_debug: Add support for physical block exponent and alignment
  cnic: add NETDEV_1000 and NETDEVICES to Kconfig select
  cnic: Fix __symbol_get() build error.
  Revert "[SCSI] cnic: fix error: implicit declaration of function ‘__symbol_get’"
  ipr: differentiate pci-x and pci-e based adapters
  ipr: add test for MSI interrupt support
  scsi_transport_spi: Blacklist Ultrium-3 tape for IU transfers
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
  asm-generic: add dummy pgprot_noncached()
  lib/checksum.c: fix endianess bug
  asm-generic: hook up new system calls
  asm-generic: list Arnd as asm-generic maintainer
  asm-generic: drop HARDIRQ_BITS definition from hardirq.h
  asm-generic: uaccess: fix up local access_ok() usage
  asm-generic: uaccess: add missing access_ok() check to strnlen_user()

* 'kmemleak' of git://linux-arm.org/linux-2.6:
  kmemleak: Do not force the slab debugging Kconfig options
  kmemleak: use pr_fmt

Indeed FOLL_WRITE matches FAULT_FLAG_WRITE, matches GUP_FLAGS_WRITE,
and it's tempting to devise a set of Grand Unified Paging flags;
but not today.  So until then, let's rely upon the compiler to spot
the coincidence, "rather than have that subtle dependency and a
comment for it" - as you remarked in another context yesterday.
Signed-off-by: NHugh Dickins <hugh.dickins@tiscali.co.uk>
Acked-by: NWu Fengguang <fengguang.wu@intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

handle_mm_fault() is now passing fault flags rather than write_access
down to hugetlb_fault(), so better recognize that in hugetlb_fault(),
and in hugetlb_no_page().
Signed-off-by: NHugh Dickins <hugh.dickins@tiscali.co.uk>
Acked-by: NWu Fengguang <fengguang.wu@intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://www.jni.nu/cris:
  CRISv10: remove redundant tests on unsigned
  CRISv32: irq.c - Move end brace outside #endif
  CRISv32: Fix potential null reference in cryptocop driver.
  CRISv32: Add arch optimized strcmp.
  CRIS: assignment/is equal confusion

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: hda - Make jack-plug notification selectable
  ALSA: ctxfi - Add PM support
  sound: seq_midi_event: fix decoding of (N)RPN events
  ALSA: hda - Add digital-mic support to ALC262 auto model
  ALSA: hda - Fix check of input source type for realtek codecs
  ALSA: hda - Add quirk for Sony VAIO Z21MN
  ALSA: hda - Get back Input Source for ALC262 toshiba-s06 model
  ALSA: hda - Fix unsigned comparison in patch_sigmatel.c
  ALSA: via82xx: add option to disable 500ms delay in snd_via82xx_codec_wait
  sound: fix check for return value in snd_pcm_hw_refine
  ALSA: ctxfi - Allow unknown PCI SSIDs
  ASoC: Blackfin: update the bf5xx_i2s_resume parameters
  ASoC: Blackfin: keep better track of SPORT configuration state

* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
  [WATCHDOG] wdt_pci.c: remove #ifdef CONFIG_WDT_501_PCI
  [WATCHDOG] hpwdt: Add NMI priority option
  [WATCHDOG] OMAP fixes: enable clock in probe, trigger timer reload
  [WATCHDOG] add bcm47xx watchdog driver
  [WATCHDOG] Freescale STMP: watchdog driver
  [WATCHDOG] twl4030 watchdog driver
  [WATCHDOG] U300 COH 901 327 watchdog driver
  [WATCHDOG] Add pnx833x_wdt

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (62 commits)
  V4L/DVB (12131): BUGFIX: An incorrect Carrier Recovery Loop optimization table was being
  V4L/DVB (12130): Fix a redundant compiler warning
  V4L/DVB (12003): v4l2: Move bounding code outside I2C ifdef block
  V4L/DVB (11913): cx231xx: TRY_FMT should not actually set anything
  V4L/DVB (11912): em28xx: Use v4l bounding/alignment function
  V4L/DVB (11911): cx231xx: Use v4l bounding/alignment function
  V4L/DVB (11910): mt9: Use v4l bounding/alignment function
  V4L/DVB (11909): cx23885: Use v4l bounding/alignment function
  V4L/DVB (11908): w8968cf: Use v4l bounding/alignment function
  V4L/DVB (11907): cx88: Use v4l bounding/alignment function
  V4L/DVB (11906): saa7134: Use v4l bounding/alignment function
  V4L/DVB (11905): vivi: Use v4l bounding/alignment function
  V4L/DVB (11904): zoran: Use v4l bounding/alignment functiob
  V4L/DVB (11903): sh_mobile_ceu_camera: Use v4l bounding/alignment function
  V4L/DVB (11902): pxa-camera: Use v4l bounding/alignment function
  V4L/DVB (11901): v4l2: Create helper function for bounding and aligning images
  V4L/DVB (12128): v4l2: update framework documentation.
  V4L/DVB (12125): v4l2: add new s_config subdev ops and v4l2_i2c_new_subdev_cfg/board calls
  V4L/DVB (12122): pvrusb2: De-obfuscate code which handles routing schemes
  V4L/DVB (12121): pvrusb2: Improve handling of routing schemes
  ...

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  libata: don't set IORDY for reset
  sata_fsl: Add power mgmt support
  [libata] PATA driver for CF interface on AT91SAM9260 SoC
  [libata] beautify module parameters

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide-2.6:
  ide cmd64x: Remove serialize setting.
  ide: Take over as maintainer.

Add __init and __exit annotations to the module_init/module_exit
functions from drivers/infiniband/core/addr.c and cma.c.
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>
Acked-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Increment version number for DMEM toleration.
Signed-off-by: NAlexander Schmidt <alexs@linux.vnet.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The isolated page is "cursor_page" not "page".

This could cause LRU list corruption under memory pressure, caught by
CONFIG_DEBUG_LIST.
Reported-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NKAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Reviewed-by: NBalbir Singh <balbir@linux.vnet.ibm.com>
Tested-by: NDaisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

That's HAVE_PERF_COUNTERS not HAVE_PERF_COUNTER. This was right
initially but I seem to have screwed it up while re-typing it out
by hand on another machine when I checked it in. Hmph.
Reported-by: NRobert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Selecting DEBUG_SLAB or SLUB_DEBUG by the KMEMLEAK menu entry may cause
issues with other dependencies (KMEMCHECK). These configuration options
aren't strictly needed by kmemleak but they may increase the chances of
finding leaks. This patch also updates the KMEMLEAK config entry help
text.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Acked-by: NPekka Enberg <penberg@cs.helsinki.fi>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

Most architectures now provide a pgprot_noncached(), the
remaining ones can simply use an dummy default implementation,
except for cris and xtensa, which should override the
default appropriately.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Magnus Damm <magnus.damm@gmail.com>