"iter" is -1 at the end of the loop and not zero.  It means we don't
print a warning message.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In __wmi_send we check if fw is ready at the beginning of the function.
While we wait for the completion of the previous command, system suspend
can be invoked and reset the HW, causing __wmi_send to read from HW
registers while it is not ready.
Taking the wmi_mutex in the reset flow when setting the FW ready bit
to zero will prevent the above race condition.
Signed-off-by: NMaya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

To prevent race when connect flow may run in parallel with
the disconnect event.

Scenario leading to the bug is: while running connect flow on the AP,
STA sends disconnect. log follows.

<7>[  668.736269] wil6210 0000:01:00.0: wlan0: DBG[ WMI]Configure for connection CID 1
<7>[  668.736269] wil6210 0000:01:00.0: wlan0: DBG[MISC]wil_vring_init_tx() max_mpdu_size 2048
<7>[  668.736301] wil6210 0000:01:00.0: wlan0: DBG[MISC]wil_vring_alloc()
<7>[  668.736363] wil6210 0000:01:00.0: wlan0: DBG[MISC]vring[1024] 0xffbe8000:d962ce08 0xdb244000
<7>[  668.736394] wil6210 0000:01:00.0: wlan0: DBG[ WMI]Head 0x00880300 -> 0x00880308
<7>[  668.736394] wil6210 0000:01:00.0: wlan0: DBG[ WMI]WMI command 0x0821 [28]
<7>[  668.736426] DBG[ WMI]Cmd 00000000: 20 00 24 00 00 00 00 00 00 00 21 08 00 00 00 00   .$.......!.....
<7>[  668.736426] DBG[ WMI]cmd 00000000: 00 00 00 00 00 00 5f 5c 00 00 00 00 00 04 00 08  ......_\........
<7>[  668.736457] DBG[ WMI]cmd 00000010: 01 01 00 00 00 00 00 00 00 00 ff 0f              ............
<7>[  668.736488] wil6210 0000:01:00.0: wlan0: DBG[ IRQ]Pseudo IRQ 0x00000004
<7>[  668.736519] wil6210 0000:01:00.0: wlan0: DBG[ WMI]Handle WMI 0x1824 (reply_id 0x1821)
<7>[  668.736519] wil6210 0000:01:00.0: wlan0: DBG[ IRQ]wil6210_mask_irq_pseudo()
<7>[  668.736519] wil6210 0000:01:00.0: wlan0: DBG[ IRQ]ISR MISC 0x20000000
<7>[  668.736551] wil6210 0000:01:00.0: wlan0: DBG[ WMI]Handle WMI 0x1003 (reply_id 0x1821)
<7>[  668.736551] wil6210 0000:01:00.0: wlan0: DBG[ WMI]Disconnect 04:ce:14:00:07:70 reason [proto 3 wmi 4]
<7>[  668.736582] wil6210 0000:01:00.0: wlan0: DBG[MISC]wil6210_disconnect()
<7>[  668.736613] wil6210 0000:01:00.0: wlan0: DBG[ IRQ]Thread IRQ
<7>[  668.736613] wil6210 0000:01:00.0: wlan0: DBG[ IRQ]Thread ISR MISC 0x20000000
<7>[  668.736644] wil6210 0000:01:00.0: wlan0: DBG[ IRQ]MBOX event
<7>[  668.736644] wil6210 0000:01:00.0: wlan0: DBG[ WMI]Mbox head 00880330 tail 00880328
<7>[  668.736676] wil6210 0000:01:00.0: wlan0: DBG[ WMI]Mbox evt 001a 0010 0000 00
<7>[  668.736676] wil6210 0000:01:00.0: wlan0: DBG[ WMI]WMI event 0x1821 MID 0 @3255145 msec
<7>[  668.736707] DBG[ WMI]evt 00000000: 1a 00 10 00 00 00 00 10 00 00 21 18 69 ab 31 00  ..........!.i.1.
<7>[  668.736707] DBG[ WMI]evt 00000010: 01 01 00 00 00 00 00 00                          ........
<7>[  668.736738] wil6210 0000:01:00.0: wlan0: DBG[ WMI]queue_work -> 0
<7>[  668.736738] wil6210 0000:01:00.0: wlan0: DBG[ WMI]wmi_recv_cmd -> 1 events queued
<7>[  668.736769] wil6210 0000:01:00.0: wlan0: DBG[ IRQ]wil6210_unmask_irq_pseudo()
<7>[  668.736832] wil6210 0000:01:00.0: wlan0: DBG[MISC]Disconnect 04:ce:14:00:07:70, CID=1, reason=3
<7>[  668.736832] wil6210 0000:01:00.0: wlan0: DBG[MISC]wil_disconnect_cid(CID 1, status 1)
<7>[  668.736894] wil6210 0000:01:00.0: wlan0: DBG[MISC]wil_vring_fini_tx() id=1
<7>[  668.736894] wil6210 0000:01:00.0: wlan0: DBG[MISC]free Tx vring 1 [1024] 0xffbe8000:d962ce08 0xdb244000
<7>[  668.736957] wil6210 0000:01:00.0: wlan0: DBG[ WMI]Handle WMI 0x1821 (reply_id 0x1821)
<7>[  668.736988] wil6210 0000:01:00.0: wlan0: DBG[ WMI]Complete WMI 0x1821
<7>[  668.737019] wil6210 0000:01:00.0: wlan0: DBG[ WMI]wmi_call(0x0821->0x1821) completed in 0 msec
<3>[  668.737019] wil6210 0000:01:00.0: wlan0: Tx config failed, status 0x01
<7>[  668.739518] wil6210 0000:01:00.0: wlan0: DBG[MISC]wil_cfg80211_del_station(04:ce:14:00:07:70, reason=2)
<7>[  668.739550] wil6210 0000:01:00.0: wlan0: DBG[MISC]wil6210_disconnect()
<7>[  668.739550] wil6210 0000:01:00.0: wlan0: DBG[MISC]_wil6210_disconnect(bssid=04:ce:14:00:07:70, reason=2, ev-)
<7>[  668.739581] wil6210 0000:01:00.0: wlan0: DBG[MISC]Disconnect 04:ce:14:00:07:70, CID=-2, reason=2
<7>[  668.742705] wil6210 0000:01:00.0: wlan0: DBG[MISC]free Tx vring 1 [1024] 0x  (null):d962ce08 0x  (null)
<3>[  668.742736] __dma_free_remap: trying to free invalid coherent area:   (null)
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NMaya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

When configuring Tx vring for new connection,
WMI call to the firmware may fail. In this case, need to
clean up properly. In particular, need to call
cfg80211_del_sta() in case of AP like interface.

Perform full "disconnect" procedure for proper clean up
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

During reset flow, ignore firmware errors detected prior
to the actual hardware reset as the recovery flow would
make additional unnecessary reset.
Signed-off-by: NHamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Hostapd request disconnect for broadcast bssid when it
wants to disconnect all stations from the AP.

Detect this and really disconnect all connected stations.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Boot loader versions as backward compatible,
starting from v1
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Boot loader reports error starting from the struct v2.

Print error info before reset (power up state) in debug mode,
and print same info as error if target reset timed out.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Replace macros like "R", "W", "S", "C", defined multiple times,
with inline functions "wil_[rwsc]".

Use "readl" and "writel" instead of "ioread32" and "iowrite32"
since it is granted that memory transactions are used,
not port ones like IN/OUT
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

When loading with debug_fw flag, do not bail out on
unknown chipId
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Use function wil_fw_error_recovery() instead of inline equivalent code
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

There are 2 versions of boot loader struct: v0 and v1.
In the v1, boot loader build version added; as well as
RF status.

Support both versions.

Boot loader structure v1 has RF status; ignore RF error if firmware
not going to be loaded; driver can still be used to interact with the HW
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Control Bcast ring size in similar way as Rx and Tx ones,
through "bcast_ring_order" modparam, actual ring size is 1 << order
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Most code already uses consts for the struct kernel_param_ops,
sweep the kernel for the last offending stragglers. Other than
include/linux/moduleparam.h and kernel/params.c all other changes
were generated with the following Coccinelle SmPL patch. Merge
conflicts between trees can be handled with Coccinelle.

In the future git could get Coccinelle merge support to deal with
patch --> fail --> grammar --> Coccinelle --> new patch conflicts
automatically for us on patches where the grammar is available and
the patch is of high confidence. Consider this a feature request.

Test compiled on x86_64 against:

	* allnoconfig
	* allmodconfig
	* allyesconfig

@ const_found @
identifier ops;
@@

const struct kernel_param_ops ops = {
};

@ const_not_found depends on !const_found @
identifier ops;
@@

-struct kernel_param_ops ops = {
+const struct kernel_param_ops ops = {
};

Generated-by: Coccinelle SmPL
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Junio C Hamano <gitster@pobox.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: cocci@systeme.lip6.fr
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NLuis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

When we disconnect from the AP, drivers call cfg80211_disconnect().
This doesn't know whether the disconnection was initiated locally
or by the AP though, which can cause problems with the supplicant,
for example with WPS. This issue obviously doesn't show up with any
mac80211 based driver since mac80211 doesn't call this function.

Fix this by requiring drivers to indicate whether the disconnect is
locally generated or not. I've tried to update the drivers, but may
not have gotten the values correct, and some drivers may currently
not be able to report correct values. In case of doubt I left it at
false, which is the current behaviour.

For libertas, make adjustments as indicated by Dan Williams.
Reported-by: NMatthieu Mauger <matthieux.mauger@intel.com>
Tested-by: NMatthieu Mauger <matthieux.mauger@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Introduce 2 types of GTK, Tx (for this STA) and Rx (for each peer).
Now, AP has only Tx GTK, STA - only Rx one. PBSS not supported yet;
for it, continue using pseudo-DMS.
Handle per-vring .1x state, update it from WMI_VRING_EN_EVENTID
event. This allows unification for unicast and broadcast vrings.
This mechanism replaces former per-CID "data_port_open"
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Boot loader "ready" indication has changed from "bit0 set"
to "only bit0 set". This is to address hardware glitches.
Due to glitches, sometimes right after reset register reads
0xffffffff, or (rarely) other garbage.

Reflect this in the driver
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

refactor module parameter debug_fw to act as "fw debug mode",
where driver do nothing but allow card memory access.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Use dedicated vring for multicast frames; this vring allocated for
AP and PBSS (both P2P GO and client) configurations

For short frames, use MCS0; for long - MCS1
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

"echo" used to be called when no firmware loaded to the NIC,
this causes error output.

Probe firmware with "echo" only after it returned "ready" event.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

For the AP, configuration may say not to bridge traffic between
wireless clients. This is conveyed from user space (ex: hostapd has
ap_isolate parameter) with NL80211_CMD_SET_BSS, to the driver's
cfg80211 ops method change_bss

Add support for this setting.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

In the old hardware, bug existed that caused DA and SA for every
Rx packet to be swapped in the AP mode.
New hardware has fix for this bug. Enable this fix in the
hardware.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Hardware older than Sparrow B0 obsolete.
There is no WiFi product that uses this hardware.
Recent firmware does not support it either.

Remove driver support.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Introduce boot loader. Instead of the operational firmware,
very small boot loader is burned to the on-board flash. Boot loader
initializes hardware upon reset, and prepares for low power mode.
Boot loader reports MAC address and detects radio chip connected.

Driver loads firmware only when bringing up interface. All information
required to set up network interface, most important is MAC address,
reported by the boot loader

The firmware composed of 2 files:
- wil6210.fw - firmware itself (compiled code + data)
- wil6210.board - board file (various board and radio dependent
  calibrations and parameters)
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Access point require this API to check peer alive status.
Assume peer is alive when it is connected, because
firmware implements keep alive checks and will disconnect
peer if it is not alive.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Interrupt moderation parameters will never be passed as module
parameters. For product, they will be hard-coded after lab testing,
and for debugging, they can be altered via debugfs.
Signed-off-by: NVladimir Shulman <qca_shulmanv@qca.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

netif_carrier_on indication was too late. In case Rx packet received
before netif_carrier_on indication, upper layers could not send
Tx packet back.

The fix is to indicate netif_carrier_on earlier:
for STA, indicate netif_carrier_on when association starts.
for AP/PCP, indicate netif_carrier_on upon starting AP/PCP.
Signed-off-by: NDedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

In the Rx reorder mechanism, nothing is done in the interrupt
context, so there is no need to use 'irq' flavors of spinlock.
Rx done in NAPI context (tasklet), other manipulations - in the
thread context.

Having interrupts enabled makes it better for the OS in general.
Besides, if enslaved under bonding, bridge or team driver, Rx
won't work with interrupts disabled.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Rx high threshold interrupt is reported by the hardware in case
when number of not utilized by the HW descriptors in the Rx ring
becomes low.
Introduce module parameter for RX high threshold.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Add advanced interrupt moderation support available since "Sparrow B0".
Legacy interrupt moderation used only one counter to moderate tx, rx,
and misc interrupts.
Advanced interrupt moderation bypasses misc, and handles separately tx
and rx interrupts. In addition it has two timers for each interrupt type.
Max burst duration timer which defines how long to postpone interrupt after
first event (receive event for rx and tx complete event for tx), and
interframe timeout which defines how to determine the end of the burst and
issue interrupt even if the first timer still pending.
Capabilities flags in wil_priv is set on initialization according to
HW. The rest of the code checks for advanced interrupt capability bit
in capabilities flags field.
Debugfs is split accordingly: "legacy" interrupt moderation remains
unchanged, new debugs files added for advanced interrupt moderation
support.
Module params are aligned to support advanced interrupt moderation
(tx & rx). When not available (for legacy interrupt moderation) will
use only rx configuration; Tx configuration will be ignored in this
case.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Use the proper reset follow based on HW capabilities
detection instead of chip ID.
Remove old hw ID mechanism which was used only for reset flow.
Remove support for Marlon A0.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

wil->status used as bitmap; use DECLARE_BITMAP for it.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When encapsulating 802.3 frames into the 802.11 ones,
8-byte SNAP header added to save ethtype. SNAP is part of
the frame body, thus should be counted in MSDU. So,
MTU = MSDU - SNAP
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When configuring Tx/Rx VRING's, driver need to specify max. MPDU size
It should take into account all overhead introduced by 802.3->208.11
transformation.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When disconnecting single STA in AP, it might be that STA
in question is already disconnected. In this case, need to do nothing.
Previously, it was mis-interpreted as "disconnect all"
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Upon Tx vring creation, initiate BACK establishment
with maximum possible window size.

When establishing secure connection, there is EAPOL data exchange
between connection itself and "data port open", where security
is done and non-EAPOL data may be transferred. It is better to
send EAPOL frames using normal ACK because of firmware considerations.

send ADDBA only is 2 conditions met:
- data port open for the corresponded STA
- vring created
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Introduce BACK establishment procedures; decision logic is not implemented
yet; debugfs entry 'addba' used to manually trigger addba/delba for ringid 0.

debugfs usage:
to establish BACK with agg_wsize 16:
  echo 16 > /sys/kernel/debug/ieee80211/phy0/wil6210/addba
to delete BACK:
  echo 0 > /sys/kernel/debug/ieee80211/phy0/wil6210/addba
to change agg_wsize, one need to delete BACK and establish it anew

ADDBA flow for:

- originator

Tx side (initiator) sends WMI_VRING_BA_EN_CMDID providing
agg_wsize and timeout parameters.
Eventually, it gets event confirming BACK agreement - WMI_BA_STATUS_EVENTID
with negotiated parameters. On this event, update Tx vring data
(struct vring_tx_data) and display BACK parameters on debugfs

- recipient

Rx side (recipient) firmware informs driver about ADDBA with
WMI_RCP_ADDBA_REQ_EVENTID, driver process it in service work
queue wq_service. It adjusts parameters and sends response
with WMI_RCP_ADDBA_RESP_CMDID, and final confirmation provided
by firmware with WMI_ADDBA_RESP_SENT_EVENTID. In case of success,
driver updates Rx BACK reorder buffer.

policy for BACK parameters:
- aggregation size (agg_wsize * MPDUsize)) to not exceed 64Kbytes

DELBA flow for:

- originator

driver decides to terminate BACK, it sends WMI_VRING_BA_DIS_CMDID
and updates struct vring_tx_data associated with vring; ignore
WMI_DELBA_EVENTID.

- recipient

firmware informs driver with WMI_DELBA_EVENTID,
driver deletes correspondent reorder buffer

ADDBA request processing requires sending WMI command, therefore
it is processed in work queue context. Same work queue used as for
connect, it get renamed to wq_service
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

If card reset with firmware download executed, followed by reset
with use of firmware from build in flash, firmware download indication
remains in the hardware register.
When running firmware download flow,
the SW download indication is written by the driver to bit 0 in usage_6:
wil_fw_load(), "S(RGF_USER_USAGE_6, 1);"
This register, like all USER RGF, wasn't reset in SW reset flow.
Therefore the driver must clear it on SW reset flow.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Allow to configure VRING size for both Rx and Tx via module parameters:
rx_ring_order and tx_ring_order. Parameters are ring size orders, i.e.
ring size calculated as 1 << order.
Defaults for both Tx and Rx are order 9, i.e. size 512
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Scan timeout treated as indication for firmware error;
and should be handled in the same way.

Recovery state machine does not perform as designed because
its state is not updated in case of scan timeout.

Fix is to set recovery state machine into the proper state.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>