Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 24 3月, 2014 10 次提交
  3. 20 3月, 2014 5 次提交
    • S
      powerpc/booke64: Critical and machine check exception support · 609af38f
      由 Scott Wood 提交于 
      Add special state saving for critical and machine check exceptions.

Most of this code could be used to handle debug exceptions taken from
kernel space, but actually doing so is outside the scope of this patch.

The various critical and machine check exceptions now point to their
real handlers, rather than hanging the kernel.
Signed-off-by: NScott Wood <scottwood@freescale.com>
      609af38f
    • S
      powerpc/booke64: Use SPRG_TLB_EXFRAME on bolted handlers · a3dc6207
      由 Scott Wood 提交于 
      While bolted handlers (including e6500) do not need to deal with a TLB
miss recursively causing another TLB miss, nested TLB misses can still
happen with crit/mc/debug exceptions -- so we still need to honor
SPRG_TLB_EXFRAME.

We don't need to spend time modifying it in the TLB miss fastpath,
though -- the special level exception will handle that.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Cc: Mihai Caraman <mihai.caraman@freescale.com>
Cc: kvm-ppc@vger.kernel.org
      a3dc6207
    • S
      powerpc/booke64: Use SPRG7 for VDSO · 9d378dfa
      由 Scott Wood 提交于 
      Previously SPRG3 was marked for use by both VDSO and critical
interrupts (though critical interrupts were not fully implemented).

In commit 8b64a9df ("powerpc/booke64:
Use SPRG0/3 scratch for bolted TLB miss & crit int"), Mihai Caraman
made an attempt to resolve this conflict by restoring the VDSO value
early in the critical interrupt, but this has some issues:

 - It's incompatible with EXCEPTION_COMMON which restores r13 from the
   by-then-overwritten scratch (this cost me some debugging time).
 - It forces critical exceptions to be a special case handled
   differently from even machine check and debug level exceptions.
 - It didn't occur to me that it was possible to make this work at all
   (by doing a final "ld r13, PACA_EXCRIT+EX_R13(r13)") until after
   I made (most of) this patch. :-)

It might be worth investigating using a load rather than SPRG on return
from all exceptions (except TLB misses where the scratch never leaves
the SPRG) -- it could save a few cycles.  Until then, let's stick with
SPRG for all exceptions.

Since we cannot use SPRG4-7 for scratch without corrupting the state of
a KVM guest, move VDSO to SPRG7 on book3e.  Since neither SPRG4-7 nor
critical interrupts exist on book3s, SPRG3 is still used for VDSO
there.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Cc: Mihai Caraman <mihai.caraman@freescale.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: kvm-ppc@vger.kernel.org
      9d378dfa
    • S
      powerpc/e6500: Make TLB lock recursive · 82d86de2
      由 Scott Wood 提交于 
      Once special level interrupts are supported, we may take nested TLB
misses -- so allow the same thread to acquire the lock recursively.

The lock will not be effective against the nested TLB miss handler
trying to write the same entry as the interrupted TLB miss handler, but
that's also a problem on non-threaded CPUs that lack TLB write
conditional.  This will be addressed in the patch that enables crit/mc
support by invalidating the TLB on return from level exceptions.
Signed-off-by: NScott Wood <scottwood@freescale.com>
      82d86de2
    • W
      powerpc/fsl: add PVR definition for E500MC and E5500 · b0b7dcbd
      由 Wang Dongsheng 提交于 
      Signed-off-by: NWang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>
      b0b7dcbd
  5. 11 3月, 2014 1 次提交
  7. 07 3月, 2014 5 次提交
    • S
      powerpc/powernv Platform dump interface · c7e64b9c
      由 Stewart Smith 提交于 
      This enables support for userspace to fetch and initiate FSP and
Platform dumps from the service processor (via firmware) through sysfs.

Based on original patch from Vasant Hegde <hegdevasant@linux.vnet.ibm.com>

Flow:
  - We register for OPAL notification events.
  - OPAL sends new dump available notification.
  - We make information on dump available via sysfs
  - Userspace requests dump contents
  - We retrieve the dump via OPAL interface
  - User copies the dump data
  - userspace sends ack for dump
  - We send ACK to OPAL.

sysfs files:
  - We add the /sys/firmware/opal/dump directory
  - echoing 1 (well, anything, but in future we may support
    different dump types) to /sys/firmware/opal/dump/initiate_dump
    will initiate a dump.
  - Each dump that we've been notified of gets a directory
    in /sys/firmware/opal/dump/ with a name of the dump type and ID (in hex,
    as this is what's used elsewhere to identify the dump).
  - Each dump has files: id, type, dump and acknowledge
    dump is binary and is the dump itself.
    echoing 'ack' to acknowledge (currently any string will do) will
    acknowledge the dump and it will soon after disappear from sysfs.

OPAL APIs:
  - opal_dump_init()
  - opal_dump_info()
  - opal_dump_read()
  - opal_dump_ack()
  - opal_dump_resend_notification()

Currently we are only ever notified for one dump at a time (until
the user explicitly acks the current dump, then we get a notification
of the next dump), but this kernel code should "just work" when OPAL
starts notifying us of all the dumps present.
Signed-off-by: NStewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
      c7e64b9c
    • S
      powerpc/powernv: Read OPAL error log and export it through sysfs · 774fea1a
      由 Stewart Smith 提交于 
      Based on a patch by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>

This patch adds support to read error logs from OPAL and export
them to userspace through a sysfs interface.

We export each log entry as a directory in /sys/firmware/opal/elog/

Currently, OPAL will buffer up to 128 error log records, we don't
need to have any knowledge of this limit on the Linux side as that
is actually largely transparent to us.

Each error log entry has the following files: id, type, acknowledge, raw.
Currently we just export the raw binary error log in the 'raw' attribute.
In a future patch, we may parse more of the error log to make it a bit
easier for userspace (e.g. to be able to display a brief summary in
petitboot without having to have a full parser).

If we have >128 logs from OPAL, we'll only be notified of 128 until
userspace starts acknowledging them. This limitation may be lifted in
the future and with this patch, that should "just work" from the linux side.

A userspace daemon should:
- wait for error log entries using normal mechanisms (we announce creation)
- read error log entry
- save error log entry safely to disk
- acknowledge the error log entry
- rinse, repeat.

On the Linux side, we read the error log when we're notified of it. This
possibly isn't ideal as it would be better to only read them on-demand.
However, this doesn't really work with current OPAL interface, so we
read the error log immediately when notified at the moment.

I've tested this pretty extensively and am rather confident that the
linux side of things works rather well. There is currently an issue with
the service processor side of things for >128 error logs though.
Signed-off-by: NStewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
      774fea1a
    • H
      powerpc/pseries: Update dynamic cache nodes for suspend/resume operation · 6b36ba84
      由 Haren Myneni 提交于 
      pHyp can change cache nodes for suspend/resume operation. Currently the
device tree is updated by drmgr in userspace after all non boot CPUs are
enabled. Hence, we do not modify the cache list based on the latest cache
nodes. Also we do not remove cache entries for the primary CPU.

This patch removes the cache list for the boot CPU, updates the device tree
before enabling nonboot CPUs and adds cache list for the boot cpu.

This patch also has the side effect that older versions of drmgr will
perform a second device tree update from userspace. While this is a
redundant waste of a couple cycles it is harmless since firmware returns the
same data for the subsequent update-nodes/properties rtas calls.
Signed-off-by: NHaren Myneni <hbabu@us.ibm.com>
Signed-off-by: NTyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
      6b36ba84
    • N
      powerpc/pseries: Use remove_memory() to remove memory · 9ac8cde9
      由 Nathan Fontenot 提交于 
      The memory remove code for powerpc/pseries should call remove_memory()
so that we are holding the hotplug_memory lock during memory remove
operations.

This patch updates the memory node remove handler to call remove_memory()
and adds a ppc_md.remove_memory() entry to handle pseries specific work
that is called from arch_remove_memory().

During memory remove in pseries_remove_memblock() we have to stay with
removing memory one section at a time. This is needed because of how memory
resources are handled. During memory add for pseries (via the probe file in
sysfs) we add memory one section at a time which gives us a memory resource
for each section. Future patches will aim to address this so will not have
to remove memory one section at a time.
Signed-off-by: NNathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
      9ac8cde9
    • M
      powerpc/book3s: Recover from MC in sapphire on SCOM read via MMIO. · 55672ecf
      由 Mahesh Salgaonkar 提交于 
      Detect and recover from machine check when inside opal on a special
scom load instructions. On specific SCOM read via MMIO we may get a machine
check exception with SRR0 pointing inside opal. To recover from MC
in this scenario, get a recovery instruction address and return to it from
MC.

OPAL will export the machine check recoverable ranges through
device tree node mcheck-recoverable-ranges under ibm,opal:

# hexdump /proc/device-tree/ibm,opal/mcheck-recoverable-ranges
0000000 0000 0000 3000 2804 0000 000c 0000 0000
0000010 3000 2814 0000 0000 3000 27f0 0000 000c
0000020 0000 0000 3000 2814 xxxx xxxx xxxx xxxx
0000030 llll llll yyyy yyyy yyyy yyyy
...
...
#

where:
	xxxx xxxx xxxx xxxx = Starting instruction address
	llll llll           = Length of the address range.
	yyyy yyyy yyyy yyyy = recovery address

Each recoverable address range entry is (start address, len,
recovery address), 2 cells each for start and recovery address, 1 cell for
len, totalling 5 cells per entry. During kernel boot time, build up the
recovery table with the list of recovery ranges from device-tree node which
will be used during machine check exception to recover from MMIO SCOM UE.
Signed-off-by: NMahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
      55672ecf
  9. 28 2月, 2014 2 次提交
    • B
      powerpc/powernv: Fix opal_xscom_{read,write} prototype · 2f3f38e4
      由 Benjamin Herrenschmidt 提交于 
      The OPAL firmware functions opal_xscom_read and opal_xscom_write
take a 64-bit argument for the XSCOM (PCB) address in order to
support the indirect mode on P8.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org> [v3.13]
      2f3f38e4
    • P
      powerpc: Increase stack redzone for 64-bit userspace to 512 bytes · 573ebfa6
      由 Paul Mackerras 提交于 
      The new ELFv2 little-endian ABI increases the stack redzone -- the
area below the stack pointer that can be used for storing data --
from 288 bytes to 512 bytes.  This means that we need to allow more
space on the user stack when delivering a signal to a 64-bit process.

To make the code a bit clearer, we define new USER_REDZONE_SIZE and
KERNEL_REDZONE_SIZE symbols in ptrace.h.  For now, we leave the
kernel redzone size at 288 bytes, since increasing it to 512 bytes
would increase the size of interrupt stack frames correspondingly.

Gcc currently only makes use of 288 bytes of redzone even when
compiling for the new little-endian ABI, and the kernel cannot
currently be compiled with the new ABI anyway.

In the future, hopefully gcc will provide an option to control the
amount of redzone used, and then we could reduce it even more.

This also changes the code in arch_compat_alloc_user_space() to
preserve the expanded redzone.  It is not clear why this function would
ever be used on a 64-bit process, though.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
CC: <stable@vger.kernel.org> [v3.13]
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
      573ebfa6
  11. 19 2月, 2014 1 次提交
  13. 17 2月, 2014 4 次提交
    • G
      powerpc/eeh: Cleanup on eeh_subsystem_enabled · 2ec5a0ad
      由 Gavin Shan 提交于 
      The patch cleans up variable eeh_subsystem_enabled so that we needn't
refer the variable directly from external. Instead, we will use
function eeh_enabled() and eeh_set_enable() to operate the variable.
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
      2ec5a0ad
    • A
      powerpc: Link VDSOs at 0x0 · a0a4419e
      由 Anton Blanchard 提交于 
      perf is failing to resolve symbols in the VDSO. A while (1)
gettimeofday() loop shows:

93.99%  [vdso]  [.] 0x00000000000005e0
 3.12%  test    [.] 00000037.plt_call.gettimeofday@@GLIBC_2.18
 2.81%  test    [.] main

The reason for this is that we are linking our VDSO shared libraries
at 1MB, which is a little weird. Even though this is uncommon, Alan
points out that it is valid and we should probably fix perf userspace.

Regardless, I can't see a reason why we are doing this. The code
is all position independent and we never rely on the VDSO ending
up at 1M (and we never place it there on 64bit tasks).

Changing our link address to 0x0 fixes perf VDSO symbol resolution:

73.18%  [vdso]  [.] 0x000000000000060c
12.39%  [vdso]  [.] __kernel_gettimeofday
 3.58%  test    [.] 00000037.plt_call.gettimeofday@@GLIBC_2.18
 2.94%  [vdso]  [.] __kernel_datapage_offset
 2.90%  test    [.] main

We still have some local symbol resolution issues that will be
fixed in a subsequent patch.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
      a0a4419e
    • A
      mm: Use ptep/pmdp_set_numa() for updating _PAGE_NUMA bit · 56eecdb9
      由 Aneesh Kumar K.V 提交于 
      Archs like ppc64 doesn't do tlb flush in set_pte/pmd functions when using
a hash table MMU for various reasons (the flush is handled as part of
the PTE modification when necessary).

ppc64 thus doesn't implement flush_tlb_range for hash based MMUs.

Additionally ppc64 require the tlb flushing to be batched within ptl locks.

The reason to do that is to ensure that the hash page table is in sync with
linux page table.

We track the hpte index in linux pte and if we clear them without flushing
hash and drop the ptl lock, we can have another cpu update the pte and can
end up with duplicate entry in the hash table, which is fatal.

We also want to keep set_pte_at simpler by not requiring them to do hash
flush for performance reason. We do that by assuming that set_pte_at() is
never *ever* called on a PTE that is already valid.

This was the case until the NUMA code went in which broke that assumption.

Fix that by introducing a new pair of helpers to set _PAGE_NUMA in a
way similar to ptep/pmdp_set_wrprotect(), with a generic implementation
using set_pte_at() and a powerpc specific one using the appropriate
mechanism needed to keep the hash table in sync.
Acked-by: NMel Gorman <mgorman@suse.de>
Reviewed-by: NRik van Riel <riel@redhat.com>
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
      56eecdb9
    • A
      powerpc/mm: Add new "set" flag argument to pte/pmd update function · 88247e8d
      由 Aneesh Kumar K.V 提交于 
      pte_update() is a powerpc-ism used to change the bits of a PTE
when the access permission is being restricted (a flush is
potentially needed).

It uses atomic operations on when needed and handles the hash
synchronization on hash based processors.

It is currently only used to clear PTE bits and so the current
implementation doesn't provide a way to also set PTE bits.

The new _PAGE_NUMA bit, when set, is actually restricting access
so it must use that function too, so this change adds the ability
for pte_update() to also set bits.

We will use this later to set the _PAGE_NUMA bit.
Acked-by: NMel Gorman <mgorman@suse.de>
Acked-by: NRik van Riel <riel@redhat.com>
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
      88247e8d
  15. 11 2月, 2014 2 次提交
    • B
      powerpc/powernv: Add iommu DMA bypass support for IODA2 · cd15b048
      由 Benjamin Herrenschmidt 提交于 
      This patch adds the support for to create a direct iommu "bypass"
window on IODA2 bridges (such as Power8) allowing to bypass iommu
page translation completely for 64-bit DMA capable devices, thus
significantly improving DMA performances.

Additionally, this adds a hook to the struct iommu_table so that
the IOMMU API / VFIO can disable the bypass when external ownership
is requested, since in that case, the device will be used by an
environment such as userspace or a KVM guest which must not be
allowed to bypass translations.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
      cd15b048
    • M
      powerpc: Fix kdump hang issue on p8 with relocation on exception enabled. · 429d2e83
      由 Mahesh Salgaonkar 提交于 
      On p8 systems, with relocation on exception feature enabled we are seeing
kdump kernel hang at interrupt vector 0xc*4400. The reason is, with this
feature enabled, exception are raised with MMU (IR=DR=1) ON with the
default offset of 0xc*4000. Since exception is raised in virtual mode it
requires the vector region to be executable without which it fails to
fetch and execute instruction at 0xc*4xxx. For default kernel since kernel
is loaded at real 0, the htab mappings sets the entire kernel text region
executable. But for relocatable kernel (e.g. kdump case) we only copy
interrupt vectors down to real 0 and never marked that region as
executable because in p7 and below we always get exception in real mode.

This patch fixes this issue by marking htab mapping range as executable
that overlaps with the interrupt vector region for relocatable kernel.

Thanks to Ben who helped me to debug this issue and find the root cause.
Signed-off-by: NMahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
      429d2e83
  17. 10 2月, 2014 2 次提交
    • T
      locking/mcs: Allow architecture specific asm files to be used for contended case · ddf1d169
      由 Tim Chen 提交于 
      This patch allows each architecture to add its specific assembly optimized
arch_mcs_spin_lock_contended and arch_mcs_spinlock_uncontended for
MCS lock and unlock functions.
Signed-off-by: NTim Chen <tim.c.chen@linux.intel.com>
Cc: Scott J Norton <scott.norton@hp.com>
Cc: Raghavendra K T <raghavendra.kt@linux.vnet.ibm.com>
Cc: AswinChandramouleeswaran <aswin@hp.com>
Cc: George Spelvin <linux@horizon.com>
Cc: Rik vanRiel <riel@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: MichelLespinasse <walken@google.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Alex Shi <alex.shi@linaro.org>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: "Figo.zhang" <figo1802@gmail.com>
Cc: "Paul E.McKenney" <paulmck@linux.vnet.ibm.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Davidlohr Bueso <davidlohr.bueso@hp.com>
Cc: Waiman Long <waiman.long@hp.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matthew R Wilcox <matthew.r.wilcox@intel.com>
Signed-off-by: NPeter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1390347382.3138.67.camel@schen9-DESKSigned-off-by: NIngo Molnar <mingo@kernel.org>
      ddf1d169
    • T
      locking/mcs: Order the header files in Kbuild of each architecture in alphabetical order · b119fa61
      由 Tim Chen 提交于 
      We perform a clean up of the Kbuid files in each architecture.
We order the files in each Kbuild in alphabetical order
by running the below script.

for i in arch/*/include/asm/Kbuild
do
        cat $i | gawk '/^generic-y/ {
                i = 3;
                do {
                        for (; i <= NF; i++) {
                                if ($i == "\\") {
                                        getline;
                                        i = 1;
                                        continue;
                                }
                                if ($i != "")
                                        hdr[$i] = $i;
                        }
                        break;
                } while (1);
                next;
        }
        // {
                print $0;
        }
        END {
                n = asort(hdr);
                for (i = 1; i <= n; i++)
                        print "generic-y += " hdr[i];
        }' > ${i}.sorted;
        mv ${i}.sorted $i;
done
Signed-off-by: NTim Chen <tim.c.chen@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Matthew R Wilcox <matthew.r.wilcox@intel.com>
Cc: AswinChandramouleeswaran <aswin@hp.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: "Paul E.McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Scott J Norton <scott.norton@hp.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: "Figo.zhang" <figo1802@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Waiman Long <waiman.long@hp.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Alex Shi <alex.shi@linaro.org>
Cc: Raghavendra K T <raghavendra.kt@linux.vnet.ibm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: George Spelvin <linux@horizon.com>
Cc: MichelLespinasse <walken@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Davidlohr Bueso <davidlohr.bueso@hp.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NPeter Zijlstra <peterz@infradead.org>
[ Fixed build bug. ]
Signed-off-by: NIngo Molnar <mingo@kernel.org>
      b119fa61
  19. 29 1月, 2014 4 次提交
  21. 28 1月, 2014 2 次提交
  23. 27 1月, 2014 2 次提交
    • P
      KVM: PPC: Book3S PR: Cope with doorbell interrupts · 40688909
      由 Paul Mackerras 提交于 
      When the PR host is running on a POWER8 machine in POWER8 mode, it
will use doorbell interrupts for IPIs.  If one of them arrives while
we are in the guest, we pop out of the guest with trap number 0xA00,
which isn't handled by kvmppc_handle_exit_pr, leading to the following
BUG_ON:

[  331.436215] exit_nr=0xa00 | pc=0x1d2c | msr=0x800000000000d032
[  331.437522] ------------[ cut here ]------------
[  331.438296] kernel BUG at arch/powerpc/kvm/book3s_pr.c:982!
[  331.439063] Oops: Exception in kernel mode, sig: 5 [#2]
[  331.439819] SMP NR_CPUS=1024 NUMA pSeries
[  331.440552] Modules linked in: tun nf_conntrack_netbios_ns nf_conntrack_broadcast ipt_MASQUERADE ip6t_REJECT xt_conntrack ebtable_nat ebtable_broute bridge stp llc ebtable_filter ebtables ip6table_nat nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv6 ip6table_mangle ip6table_security ip6table_raw ip6table_filter ip6_tables iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack iptable_mangle iptable_security iptable_raw virtio_net kvm binfmt_misc ibmvscsi scsi_transport_srp scsi_tgt virtio_blk
[  331.447614] CPU: 11 PID: 1296 Comm: qemu-system-ppc Tainted: G      D      3.11.7-200.2.fc19.ppc64p7 #1
[  331.448920] task: c0000003bdc8c000 ti: c0000003bd32c000 task.ti: c0000003bd32c000
[  331.450088] NIP: d0000000025d6b9c LR: d0000000025d6b98 CTR: c0000000004cfdd0
[  331.451042] REGS: c0000003bd32f420 TRAP: 0700   Tainted: G      D       (3.11.7-200.2.fc19.ppc64p7)
[  331.452331] MSR: 800000000282b032 <SF,VEC,VSX,EE,FP,ME,IR,DR,RI>  CR: 28004824  XER: 20000000
[  331.454616] SOFTE: 1
[  331.455106] CFAR: c000000000848bb8
[  331.455726]
GPR00: d0000000025d6b98 c0000003bd32f6a0 d0000000026017b8 0000000000000032
GPR04: c0000000018627f8 c000000001873208 320d0a3030303030 3030303030643033
GPR08: c000000000c490a8 0000000000000000 0000000000000000 0000000000000002
GPR12: 0000000028004822 c00000000fdc6300 0000000000000000 00000100076ec310
GPR16: 000000002ae343b8 00003ffffd397398 0000000000000000 0000000000000000
GPR20: 00000100076f16f4 00000100076ebe60 0000000000000008 ffffffffffffffff
GPR24: 0000000000000000 0000008001041e60 0000000000000000 0000008001040ce8
GPR28: c0000003a2d80000 0000000000000a00 0000000000000001 c0000003a2681810
[  331.466504] NIP [d0000000025d6b9c] .kvmppc_handle_exit_pr+0x75c/0xa80 [kvm]
[  331.466999] LR [d0000000025d6b98] .kvmppc_handle_exit_pr+0x758/0xa80 [kvm]
[  331.467517] Call Trace:
[  331.467909] [c0000003bd32f6a0] [d0000000025d6b98] .kvmppc_handle_exit_pr+0x758/0xa80 [kvm] (unreliable)
[  331.468553] [c0000003bd32f750] [d0000000025d98f0] kvm_start_lightweight+0xb4/0xc4 [kvm]
[  331.469189] [c0000003bd32f920] [d0000000025d7648] .kvmppc_vcpu_run_pr+0xd8/0x270 [kvm]
[  331.469838] [c0000003bd32f9c0] [d0000000025cf748] .kvmppc_vcpu_run+0xc8/0xf0 [kvm]
[  331.470790] [c0000003bd32fa50] [d0000000025cc19c] .kvm_arch_vcpu_ioctl_run+0x5c/0x1b0 [kvm]
[  331.471401] [c0000003bd32fae0] [d0000000025c4888] .kvm_vcpu_ioctl+0x478/0x730 [kvm]
[  331.472026] [c0000003bd32fc90] [c00000000026192c] .do_vfs_ioctl+0x4dc/0x7a0
[  331.472561] [c0000003bd32fd80] [c000000000261cc4] .SyS_ioctl+0xd4/0xf0
[  331.473095] [c0000003bd32fe30] [c000000000009ed8] syscall_exit+0x0/0x98
[  331.473633] Instruction dump:
[  331.473766] 4bfff9b4 2b9d0800 419efc18 60000000 60420000 3d220000 e8bf11a0 e8df12a8
[  331.474733] 7fa4eb78 e8698660 48015165 e8410028 <0fe00000> 813f00e4 3ba00000 39290001
[  331.475386] ---[ end trace 49fc47d994c1f8f2 ]---
[  331.479817]

This fixes the problem by making kvmppc_handle_exit_pr() recognize the
interrupt.  We also need to jump to the doorbell interrupt handler in
book3s_segment.S to handle the interrupt on the way out of the guest.
Having done that, there's nothing further to be done in
kvmppc_handle_exit_pr().
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAlexander Graf <agraf@suse.de>
      40688909
    • M
      KVM: PPC: Book3S HV: Add new state for transactional memory · 7b490411
      由 Michael Neuling 提交于 
      Add new state for transactional memory (TM) to kvm_vcpu_arch.  Also add
asm-offset bits that are going to be required.

This also moves the existing TFHAR, TFIAR and TEXASR SPRs into a
CONFIG_PPC_TRANSACTIONAL_MEM section.  This requires some code changes to
ensure we still compile with CONFIG_PPC_TRANSACTIONAL_MEM=N.  Much of the added
the added #ifdefs are removed in a later patch when the bulk of the TM code is
added.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
[agraf: fix merge conflict]
Signed-off-by: NAlexander Graf <agraf@suse.de>
      7b490411