The delay was added because of a desire to ensure that the VF driver can
finish up removing. However, pci_disable_sriov already has its own
ssleep() call that will sleep for an entire second, so there is no
reason to add extra delay on top of this by using msleep here. In
practice, an msleep() won't have a huge impact on timing but there is no
real value in keeping it, so lets just simplify the code and remove it.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Just as we do in i40e_reset_all_vfs, save some time when freeing VFs by
amortizing the wait time for stopping queues. We can use
i40e_vsi_stop_rings_no_wait() to begin the process of stopping all the
VF rings at once. Then, once we've started the process on each VF we can
begin waiting for the VFs to stop. This helps reduce the total wait time
by a large factor.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch corrects a major oversight in that we were not reprogramming the
ports after a reset.  As a result we completely lost all of the Rx tunnel
offloads on receive including Rx checksum, RSS on inner headers, and ATR.

The fix for this is pretty standard as all we needed to do is reset the
filter bits to pending for all active filters and schedule the sync event.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The .index field of i40e_udp_port_config represents the udp port number.
Rename this variable to port so that it is more obvious.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When allocating a large number of VFs, the driver previously used
i40e_reset_vf in a sequence. Just as when performing a normal reset,
this accumulates a large amount of delay for handling all of the VFs in
sequence. This delay is mainly due to a hardware requirement to wait
after initiating a reset on the VF.

We recently added a new function, i40e_reset_all_vfs() which can be used
to amortize the delay time, by first triggering all VF resets, then
waiting once, and finally cleaning up and allocating the VFs. This is
almost as good as truly running the resets in parallel.

In order to avoid sending a spurious reset message to a client
interface, we have a check to see whether we've assigned
pf->num_alloc_vfs yet. This was originally intended as a way to
distinguish the "initialization" case from the regular reset case.

Unfortunately, this means that we can't directly use i40e_reset_all_vfs
yet. Lets avoid this check of pf->num_alloc_vfs by replacing it with
a proper VSI state bit which we can use instead. This makes the
intention much clearer and allows us to re-use the i40e_reset_all_vfs
function directly.

Change-ID: I694279b37eb6b5a91b6670182d0c15d10244fd6e
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Reviewed-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

These flags represent the state of the VF at various times. Do not
spell them as _STAT_ which can be confusing to readers who may think
these refer to statistics.

Change-ID: I6bc092cd472e8276896a1fd7498aced2084312df
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Jeff Kirsher says:

====================
10GbE Intel Wired LAN Driver Updates 2017-04-29

This series contains updates to ixgbe and ixgbevf only, most notable is
the addition of XDP support to our 10GbE drivers.

Paul fixes ixgbe to acquire the PHY semaphore before accessing PHY
registers when issuing a device reset.

John adds XDP support (yeah!) for ixgbe.

Emil fixes an issue by flushing the MACVLAN filters on VF reset to avoid
conflicts with other VFs that may end up using the same MAC address.  Also
fixed a bug where ethtool -S displayed some empty fields for ixgbevf
because it was using ixgbe_stats instead ixgbevf_stats for
IXGBEVF_QUEUE_STATS_LEN.

Tony adds the ability to specify a zero MAC address in order to clear the
VF's MAC address from the RAR table.  Also adds support for a new
1000Base-T device based on x550EM_X MAC type.  Fixed an issue where the
RSS key specified by the user would be over-written with a pre-existing
value, so change the rss_key to a pointer so we can check to see if the
key has a value set before attempting to set it.  Fixed the logic for
mailbox support for getting RETA and RSS values, which are only supported
by 82599 and x540 devices.

v2: fixed up patches #2 and #3 based on feedback from Jakub and to
    address build issues when page sizes are larger than 4k
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The RSS key is being repopulated every time the interface is brought up
regardless of whether there is an existing value. If the user sets the RSS
key and the interface is brought up (e.g. reset), the user specified RSS
key will be overwritten.

This patch changes the rss_key to a pointer so we can check to see if the
key has been populated and preserve it accordingly.
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Mailbox support for getting RETA and RSS is available for only 82599 and
x540; a previous patch reversed the logic and these adapters were
returning not supported.

Also, the NACK check in ixgbevf_get_rss_key_locked() was checking for the
command IXGBE_VF_GET_RETA instead of IXGBE_VF_GET_RSS_KEY.

This patch corrects both issues by correcting the logic and checking for
the right command.
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The RSS key is being repopulated every time the interface is brought up
regardless of whether there is an existing value. If the user sets the RSS
key and the interface is brought up (e.g. reset), the user specified RSS
key will be overwritten.

This patch changes the rss_key to a pointer so we can check to see if the
key has been populated and preserve it accordingly.
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add support for new 1000Base-T device based on X550EM_X MAC
type. All PHY operations are disabled as the PHY is controlled
by FW.
Signed-off-by: NPaul Greenwalt <paul.greenwalt@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently, there is no logic that allows a VF's MAC address to be removed
from the RAR table.

Allow the user to specify a zero MAC address in order to clear the VF's
MAC address from the RAR table.  This functionality is also utilized by
libvirt when removing VFs.
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

IXGBEVF_QUEUE_STATS_LEN is based on ixgebvf_stats, not ixgbe_stats.

This change fixes a bug where ethtool -S displayed some empty fields.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Flush the macvlan filters on VF reset to avoid conflict with other VFs that
may end up using the same MAC address.

The main change here is the call to ixgbe_set_vf_macvlan() with index 0.

Moved ixgbe_set_vf_macvlan() in front of ixgbe_vf_reset_event() to avoid
adding a prototype.
Reported-by: NSritej Kanakadandi Sritej Rama <skanakad@cisco.com>
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Current XDP implementation hits the tail on every XDP_TX return
code. This patch changes driver behavior to only hit the tail after
packet processing is complete.

With this patch I can run XDP drop programs @ 14+Mpps and XDP_TX
programs are at ~13.5Mpps.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

A couple design choices were made here. First I use a new ring
pointer structure xdp_ring[] in the adapter struct instead of
pushing the newly allocated XDP TX rings into the tx_ring[]
structure. This means we have to duplicate loops around rings
in places we want to initialize both TX rings and XDP rings.
But by making it explicit it is obvious when we are using XDP
rings and when we are using TX rings. Further we don't have
to do ring arithmatic which is error prone. As a proof point
for doing this my first patches used only a single ring structure
and introduced bugs in FCoE code and macvlan code paths.

Second I am aware this is not the most optimized version of
this code possible. I want to get baseline support in using
the most readable format possible and then once this series
is included I will optimize the TX path in another series
of patches.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Basic XDP drop support for ixgbe. Uses READ_ONCE/xchg semantics on XDP
programs instead of RCU primitives as suggested by Daniel Borkmann and
Alex Duyck.

v2: fix the build issues seen w/ XDP when page sizes are larger than 4K
    and made minor fixes based on feedback from Jakub Kicinski
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Acked-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

A recent firmware change fixed an issue to acquire the PHY semaphore before
accessing PHY registers. This led to a case where  SW can issue a device
reset clearing the MDIO registers. This patch makes SW acquire the PHY
semaphore before issuing a device reset.
Signed-off-by: NPaul Greenwalt <paul.greenwalt@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Daniel Borkmann says:

====================
Misc BPF updates

This set cleans up ldimm64 leftovers from early eBPF days and
adds couple of test cases related to this to the verifier test
suite. It also cleans up the kallsyms spinlock (had same patch
also in queue) by relaxing it through switching to _bh variant.
It fixes up test_progs in relation to htons/ntohs and adds
accessor macros for the percpu tests in test_maps.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To overcome bugs as described and fixed in 89087c45 ("bpf: Fix
values type used in test_maps"), provide a generic BPF_DECLARE_PERCPU()
and bpf_percpu() accessor macro for all percpu map values used in
tests.

Declaring variables works as follows (also works for structs):

  BPF_DECLARE_PERCPU(uint32_t, my_value);

They can then be accessed normally as uint32_t type through:

  bpf_percpu(my_value, <cpu_nr>)

For example:

  bpf_percpu(my_value, 0)++;

Implicitly, we make sure that the passed type is allocated and aligned
by gcc at least on a 8-byte boundary, so that it works together with
the map lookup/update syscall for percpu maps. We use it as a usage
example in test_maps, so that others are free to adapt this into their
code when necessary.
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Dave reported that on sparc test_progs generates buggy swapped
eth->h_proto protocol comparisons:

  10: (15) if r3 == 0xdd86 goto pc+9
   R0=imm2,min_value=2,max_value=2 R1=pkt(id=0,off=0,r=14) R2=pkt_end R3=inv
   R4=pkt(id=0,off=14,r=14) R5=inv56 R10=fp

This is due to the unconditional ...

  #define htons __builtin_bswap16
  #define ntohs __builtin_bswap16

... in test_progs that causes this. Make use of asm/byteorder.h
and use __constant_htons() where possible and only perform the
bswap16 when on little endian in non-constant case.

Fixes: 6882804c ("selftests/bpf: add a test for overlapping packet range checks")
Fixes: 37821613 ("selftests/bpf: add l4 load balancer test based on sched_cls")
Reported-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hannes rightfully spotted that the bpf_lock doesn't need to be
irqsave variant. We never perform any such updates where this
would be necessary (neither right now nor in future), therefore
relax this further.
Signed-off-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add several test cases around ldimm64, fp arithmetic and direct
packet access.
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For both cases, the verifier is already rejecting such invalid
formed instructions. Thus, remove these artifacts from old times
and align it with ppc64, sparc64 and s390x JITs that don't have
them in the first place.
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Steffen Klassert says:

====================
pull request (net-next): ipsec-next 2017-04-28

Just one patch to fix a misplaced spin_unlock_bh in an error path.

Please pull or let me know if there are problems.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge tag 'mac80211-next-for-davem-2017-04-28' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next

Johannes Berg says:

====================
Another set of patches for -next:
 * API support for concurrent scheduled scan requests
 * API changes for roaming reporting
 * BSS max idle support in mac80211
 * API changes for TX status reporting in mac80211
 * API changes for RX rate reporting in mac80211
 * rewrite monitor logic to prepare for BPF filters
 * bugfix for rare devices without 2.4 GHz support
 * a bugfix for recent DFS changes
 * some further cleanups

The API changes are actually at a nice time, since it's
typically quiet just before the merge window, and trees
can be synchronized easily during it.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The commit 6d684e54 ("rhashtable: Cap total number of entries
to 2^31") breaks rhashtable users that do not set max_size.  This
is because when max_size is zero max_elems is also incorrectly set
to zero instead of 2^31.

This patch fixes it by only lowering max_elems when max_size is not
zero.

Fixes: 6d684e54 ("rhashtable: Cap total number of entries to 2^31")
Reported-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reported-by: Nkernel test robot <fengguang.wu@intel.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Have proper request id filled in the SCHED_SCAN_RESULTS and
SCHED_SCAN_STOPPED notifications toward user-space by having the
driver provide it through the api.
Reviewed-by: NHante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: NFranky Lin <franky.lin@broadcom.com>
Signed-off-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Parse the BSS max idle period element and set the BSS configuration
accordingly so the driver can use this information to configure the
max idle period and to use protected management frames for keep alive
when required.

The BSS max idle period element is defined in IEEE802.11-2016,
section 9.4.2.79
Signed-off-by: NAvraham Stern <avraham.stern@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

cfg80211_roamed() and cfg80211_roamed_bss() take the same arguments
except that cfg80211_roamed() requires the BSSID and
cfg80211_roamed_bss() requires the bss entry.

Unify the two functions by using a struct for driver initiated
roaming information so that either the BSSID or the bss entry can be
passed as an argument to the unified function.
Signed-off-by: NAvraham Stern <avraham.stern@intel.com>
[modified the ath6k, brcm80211, rndis and wlan-ng drivers accordingly]
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
[modify brcmfmac to remove the useless cast, spotted by Arend]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Existing API 'ieee80211_get_sdata_band' returns default 2 GHz band even
if the channel context configuration is NULL. This crashes for chipsets
which support 5 Ghz alone when it tries to access members of 'sband'.
Channel context configuration can be NULL in multivif case and when
channel switch is in progress (or) when it fails. Fix this by replacing
the API 'ieee80211_get_sdata_band' with  'ieee80211_get_sband' which
returns a NULL pointer for sband when the channel configuration is NULL.

An example scenario is as below:

In multivif mode (AP + STA) with drivers like ath10k, when we do a
channel switch in the AP vif (which has a number of clients connected)
and a STA vif which is connected to some other AP, when the channel
switch in AP vif fails, while the STA vifs tries to connect to the
other AP, there is a window where the channel context is NULL/invalid
and this results in a crash  while the clients connected to the AP vif
tries to reconnect and this race is very similar to the one investigated
by Michal in https://patchwork.kernel.org/patch/3788161/ and this does
happens with hardware that supports 5Ghz alone after long hours of
testing with continuous channel switch on the AP vif

ieee80211 phy0: channel context reservation cannot be finalized because
some interfaces aren't switching
wlan0: failed to finalize CSA, disconnecting
wlan0-1: deauthenticating from 8c:fd:f0:01:54:9c by local choice
	(Reason: 3=DEAUTH_LEAVING)

	WARNING: CPU: 1 PID: 19032 at net/mac80211/ieee80211_i.h:1013 sta_info_alloc+0x374/0x3fc [mac80211]
	[<bf77272c>] (sta_info_alloc [mac80211])
	[<bf78776c>] (ieee80211_add_station [mac80211]))
	[<bf73cc50>] (nl80211_new_station [cfg80211])

	Unable to handle kernel NULL pointer dereference at virtual
	address 00000014
	pgd = d5f4c000
	Internal error: Oops: 17 [#1] PREEMPT SMP ARM
	PC is at sta_info_alloc+0x380/0x3fc [mac80211]
	LR is at sta_info_alloc+0x37c/0x3fc [mac80211]
	[<bf772738>] (sta_info_alloc [mac80211])
	[<bf78776c>] (ieee80211_add_station [mac80211])
	[<bf73cc50>] (nl80211_new_station [cfg80211]))

Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This allows the driver to pass in struct ieee80211_tx_status directly.
Make ieee80211_tx_status_noskb a wrapper around it.

As with ieee80211_tx_status_noskb, there is no _ni variant of this call,
because it probably won't be needed.

Even if the driver won't provide any extra status info other than what's
in struct ieee80211_tx_info already, it can optimize status reporting
this way by passing in the station pointer.
Signed-off-by: NFelix Fietkau <nbd@nbd.name>
[use C99 initializers]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Makes further cleanups more readable
Signed-off-by: NFelix Fietkau <nbd@nbd.name>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Rename .tx_status_noskb to .tx_status_ext and pass a new on-stack
struct ieee80211_tx_status instead of struct ieee80211_tx_info.

This struct can be used to pass extra information, e.g. for dynamic tx
power control
Signed-off-by: NFelix Fietkau <nbd@nbd.name>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Instead of hand-coding the bit manipulations, use the bitfield
macros to generate the code for the encoded bitrate.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This field will need to be used again for HE, so rename it now.

Again, mostly done with this spatch:

@@
expression status;
@@
-status->vht_nss
+status->nss
@@
expression status;
@@
-status.vht_nss
+status.nss
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

We currently use a lot of flags that are mutually incompatible,
separate this out into actual encoding and bandwidth enum values.

Much of this again done with spatch, with manual post-editing,
mostly to add the switch statements and get rid of the conversions.

@@
expression status;
@@
-status->enc_flags |= RX_ENC_FLAG_80MHZ
+status->bw = RATE_INFO_BW_80
@@
expression status;
@@
-status->enc_flags |= RX_ENC_FLAG_40MHZ
+status->bw = RATE_INFO_BW_40
@@
expression status;
@@
-status->enc_flags |= RX_ENC_FLAG_20MHZ
+status->bw = RATE_INFO_BW_20
@@
expression status;
@@
-status->enc_flags |= RX_ENC_FLAG_160MHZ
+status->bw = RATE_INFO_BW_160
@@
expression status;
@@
-status->enc_flags |= RX_ENC_FLAG_5MHZ
+status->bw = RATE_INFO_BW_5
@@
expression status;
@@
-status->enc_flags |= RX_ENC_FLAG_10MHZ
+status->bw = RATE_INFO_BW_10

@@
expression status;
@@
-status->enc_flags |= RX_ENC_FLAG_VHT
+status->encoding = RX_ENC_VHT
@@
expression status;
@@
-status->enc_flags |= RX_ENC_FLAG_HT
+status->encoding = RX_ENC_HT
@@
expression status;
@@
-status.enc_flags |= RX_ENC_FLAG_VHT
+status.encoding = RX_ENC_VHT
@@
expression status;
@@
-status.enc_flags |= RX_ENC_FLAG_HT
+status.encoding = RX_ENC_HT

@@
expression status;
@@
-(status->enc_flags & RX_ENC_FLAG_HT)
+(status->encoding == RX_ENC_HT)
@@
expression status;
@@
-(status->enc_flags & RX_ENC_FLAG_VHT)
+(status->encoding == RX_ENC_VHT)

@@
expression status;
@@
-(status->enc_flags & RX_ENC_FLAG_5MHZ)
+(status->bw == RATE_INFO_BW_5)
@@
expression status;
@@
-(status->enc_flags & RX_ENC_FLAG_10MHZ)
+(status->bw == RATE_INFO_BW_10)
@@
expression status;
@@
-(status->enc_flags & RX_ENC_FLAG_40MHZ)
+(status->bw == RATE_INFO_BW_40)
@@
expression status;
@@
-(status->enc_flags & RX_ENC_FLAG_80MHZ)
+(status->bw == RATE_INFO_BW_80)
@@
expression status;
@@
-(status->enc_flags & RX_ENC_FLAG_160MHZ)
+(status->bw == RATE_INFO_BW_160)
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In preparation for adding support for HE rates, clean up
the driver report encoding for rate/bandwidth reporting
on RX frames.

Much of this patch was done with the following spatch:

@@
expression status;
@@
-status->flag & (RX_FLAG_HT | RX_FLAG_VHT)
+status->enc_flags & (RX_ENC_FLAG_HT | RX_ENC_FLAG_VHT)

@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_SHORTPRE
+status->enc_flags op RX_ENC_FLAG_SHORTPRE
@@
expression status;
@@
-status->flag & RX_FLAG_SHORTPRE
+status->enc_flags & RX_ENC_FLAG_SHORTPRE

@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_HT
+status->enc_flags op RX_ENC_FLAG_HT
@@
expression status;
@@
-status->flag & RX_FLAG_HT
+status->enc_flags & RX_ENC_FLAG_HT

@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_40MHZ
+status->enc_flags op RX_ENC_FLAG_40MHZ
@@
expression status;
@@
-status->flag & RX_FLAG_40MHZ
+status->enc_flags & RX_ENC_FLAG_40MHZ

@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_SHORT_GI
+status->enc_flags op RX_ENC_FLAG_SHORT_GI
@@
expression status;
@@
-status->flag & RX_FLAG_SHORT_GI
+status->enc_flags & RX_ENC_FLAG_SHORT_GI

@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_HT_GF
+status->enc_flags op RX_ENC_FLAG_HT_GF
@@
expression status;
@@
-status->flag & RX_FLAG_HT_GF
+status->enc_flags & RX_ENC_FLAG_HT_GF

@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_VHT
+status->enc_flags op RX_ENC_FLAG_VHT
@@
expression status;
@@
-status->flag & RX_FLAG_VHT
+status->enc_flags & RX_ENC_FLAG_VHT

@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_STBC_MASK
+status->enc_flags op RX_ENC_FLAG_STBC_MASK
@@
expression status;
@@
-status->flag & RX_FLAG_STBC_MASK
+status->enc_flags & RX_ENC_FLAG_STBC_MASK

@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_LDPC
+status->enc_flags op RX_ENC_FLAG_LDPC
@@
expression status;
@@
-status->flag & RX_FLAG_LDPC
+status->enc_flags & RX_ENC_FLAG_LDPC

@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_10MHZ
+status->enc_flags op RX_ENC_FLAG_10MHZ
@@
expression status;
@@
-status->flag & RX_FLAG_10MHZ
+status->enc_flags & RX_ENC_FLAG_10MHZ

@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_5MHZ
+status->enc_flags op RX_ENC_FLAG_5MHZ
@@
expression status;
@@
-status->flag & RX_FLAG_5MHZ
+status->enc_flags & RX_ENC_FLAG_5MHZ

@@
assignment operator op;
expression status;
@@
-status->vht_flag op RX_VHT_FLAG_80MHZ
+status->enc_flags op RX_ENC_FLAG_80MHZ
@@
expression status;
@@
-status->vht_flag & RX_VHT_FLAG_80MHZ
+status->enc_flags & RX_ENC_FLAG_80MHZ

@@
assignment operator op;
expression status;
@@
-status->vht_flag op RX_VHT_FLAG_160MHZ
+status->enc_flags op RX_ENC_FLAG_160MHZ
@@
expression status;
@@
-status->vht_flag & RX_VHT_FLAG_160MHZ
+status->enc_flags & RX_ENC_FLAG_160MHZ

@@
assignment operator op;
expression status;
@@
-status->vht_flag op RX_VHT_FLAG_BF
+status->enc_flags op RX_ENC_FLAG_BF
@@
expression status;
@@
-status->vht_flag & RX_VHT_FLAG_BF
+status->enc_flags & RX_ENC_FLAG_BF

@@
assignment operator op;
expression status, STBC;
@@
-status->flag op STBC << RX_FLAG_STBC_SHIFT
+status->enc_flags op STBC << RX_ENC_FLAG_STBC_SHIFT

@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_SHORTPRE
+status.enc_flags op RX_ENC_FLAG_SHORTPRE
@@
expression status;
@@
-status.flag & RX_FLAG_SHORTPRE
+status.enc_flags & RX_ENC_FLAG_SHORTPRE

@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_HT
+status.enc_flags op RX_ENC_FLAG_HT
@@
expression status;
@@
-status.flag & RX_FLAG_HT
+status.enc_flags & RX_ENC_FLAG_HT

@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_40MHZ
+status.enc_flags op RX_ENC_FLAG_40MHZ
@@
expression status;
@@
-status.flag & RX_FLAG_40MHZ
+status.enc_flags & RX_ENC_FLAG_40MHZ

@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_SHORT_GI
+status.enc_flags op RX_ENC_FLAG_SHORT_GI
@@
expression status;
@@
-status.flag & RX_FLAG_SHORT_GI
+status.enc_flags & RX_ENC_FLAG_SHORT_GI

@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_HT_GF
+status.enc_flags op RX_ENC_FLAG_HT_GF
@@
expression status;
@@
-status.flag & RX_FLAG_HT_GF
+status.enc_flags & RX_ENC_FLAG_HT_GF

@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_VHT
+status.enc_flags op RX_ENC_FLAG_VHT
@@
expression status;
@@
-status.flag & RX_FLAG_VHT
+status.enc_flags & RX_ENC_FLAG_VHT

@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_STBC_MASK
+status.enc_flags op RX_ENC_FLAG_STBC_MASK
@@
expression status;
@@
-status.flag & RX_FLAG_STBC_MASK
+status.enc_flags & RX_ENC_FLAG_STBC_MASK

@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_LDPC
+status.enc_flags op RX_ENC_FLAG_LDPC
@@
expression status;
@@
-status.flag & RX_FLAG_LDPC
+status.enc_flags & RX_ENC_FLAG_LDPC

@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_10MHZ
+status.enc_flags op RX_ENC_FLAG_10MHZ
@@
expression status;
@@
-status.flag & RX_FLAG_10MHZ
+status.enc_flags & RX_ENC_FLAG_10MHZ

@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_5MHZ
+status.enc_flags op RX_ENC_FLAG_5MHZ
@@
expression status;
@@
-status.flag & RX_FLAG_5MHZ
+status.enc_flags & RX_ENC_FLAG_5MHZ

@@
assignment operator op;
expression status;
@@
-status.vht_flag op RX_VHT_FLAG_80MHZ
+status.enc_flags op RX_ENC_FLAG_80MHZ
@@
expression status;
@@
-status.vht_flag & RX_VHT_FLAG_80MHZ
+status.enc_flags & RX_ENC_FLAG_80MHZ

@@
assignment operator op;
expression status;
@@
-status.vht_flag op RX_VHT_FLAG_160MHZ
+status.enc_flags op RX_ENC_FLAG_160MHZ
@@
expression status;
@@
-status.vht_flag & RX_VHT_FLAG_160MHZ
+status.enc_flags & RX_ENC_FLAG_160MHZ

@@
assignment operator op;
expression status;
@@
-status.vht_flag op RX_VHT_FLAG_BF
+status.enc_flags op RX_ENC_FLAG_BF
@@
expression status;
@@
-status.vht_flag & RX_VHT_FLAG_BF
+status.enc_flags & RX_ENC_FLAG_BF

@@
assignment operator op;
expression status, STBC;
@@
-status.flag op STBC << RX_FLAG_STBC_SHIFT
+status.enc_flags op STBC << RX_ENC_FLAG_STBC_SHIFT

@@
@@
-RX_FLAG_STBC_SHIFT
+RX_ENC_FLAG_STBC_SHIFT
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Merge tag 'wireless-drivers-next-for-davem-2017-04-27' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
wireless-drivers-next patches for 4.12

Few remaining patches for 4.12 submitted during the last week.

Major changes:

iwlwifi

* the firmware for 7265D and 3168 NICs is frozen at version 29

* more support for the upcoming A000 series
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sudarsana Reddy Kalluru says:

====================
qed*: PTP enhancements.

The patch series contains set of enhancements for qed/qede ptp
implementation.
Patches (1)-(3) adds resource locking implementation to allow
PTP functionality only on the first detected ethernet PF of the port.
The change is required as the adapter currently supports only one
instance of the PTP client on a given port.
Patch (4) removes the un-needed header file.
Patch (5) moves the ptt-lock get/release logic to the ptp specific
code.

Please consider applying this series to "net-next" branch.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>