I am unclear how this got messed up in the shuffle, but it did.

Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This patch existed before, but was lost over time.

Note that reset is still somewhat problematic in my limited testing (ie.
module_reload will not pass) but it can be disabled with a module
parameter, and support should be considered preliminary anyway.
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Prior to Haswell the CPU control register for backlight
(BLC_PWM_CPU_CTL) toggled the PCH baclight pin for us. This made some
sense as there was no pin on the CPU. With Haswell came the introduction
of a CPU backlight pin, but the interface was still controlled by
software with the same mechnism. Behind the scenes, hardware did all the
dirty work for us.

Broadwell no longer provides this for free. If we want to use the PCH
backlight pin [1] then we have to set the override bit BLC_PWM_PCH_CTL1
and program BLC_PWM_PCH_CTL2 for the PWM values.

This patch implements that. This patch is compile tested only, and given
that I rarely if ever touch this code, careful review is welcome.

[1] According to Art, we know of no devices that exist which use the CPU
pin (and remember it has existed already on HSW). If such a device does
exist, we'll have to handle it properly - this is left as TODO until
then.

v2: Drop the abstraction prep patch, as a bigger backlight overhaul is
    in the works, and do just the mimimal bdw enabling now. (by Jani)

CC: Art Runyan <arthur.j.runyan@intel.com>
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

For what we care about ULT and ULX are interchangeable. We know of 3
types of pciids for these cases. I am not sure if at some point we will
need to distinguish ULT and ULX.

Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Fix a long-standing TTM issue where we manipulated the vma page_prot
bits while mmap_sem was taken in read mode only. We now make a local
copy of the vma structure which we pass when we set the ptes.
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: NJerome Glisse <jglisse@redhat.com>

Fixes
 *) an implicit function declaration on mips,
 *) a defined but not used label on !CONFIG_INTEL_IOMMU
 *) Hopefully a couple of sparse warnings where we implicitly typecast
    integer to __le32 and vice versa.
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: NBrian Paul <brianp@vmware.com>

Fix an error message that was incorrectly blaming device resource id
shortage.

Also make sure we correctly catch resource eviction errors, that
could otherwise lead to evictable resources temporarily not being on the
LRU list.
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: NJakob Bornecrantz <jakob@vmware.com>
Cc: stable@vger.kernel.org

The vrefresh field of the mode is 0 for most modes
fetched from the EDID (e.g., established timings).
When dealing with monitors that have a bogus preferred
mode, we may not always select the mode we want because
we compare the target refresh to the mode's vrefresh which
is 0 in a lot of cases.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>

Turn clk_enable() and clk_disable() calls into clk_prepare_enable() and
clk_disable_unprepare() to get ready for the migration to the common
clock framework.

Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This uses the proper div macro.
Signed-off-by: NDave Airlie <airlied@redhat.com>

Fix CONFIG_ACPI=n build fail

  CC      drivers/gpu/drm/i915/intel_opregion.o
drivers/gpu/drm/i915/intel_opregion.c: In function ‘intel_opregion_setup’:
drivers/gpu/drm/i915/intel_opregion.c:879:2: error: ‘asle_work’ undeclared (first use in this function)
drivers/gpu/drm/i915/intel_opregion.c:879:2: note: each undeclared identifier is reported only once for each function it appears in
make[4]: *** [drivers/gpu/drm/i915/intel_opregion.o] Error 1

introduced in
commit 91a60f20
Author: Jani Nikula <jani.nikula@intel.com>
Date:   Thu Oct 31 18:55:48 2013 +0200

    drm/i915: move opregion asle request handling to a work queue
Reported-by: NJim Davis <jim.epost@gmail.com>
Reference: http://lkml.kernel.org/r/CA+r1ZhjcFpr5KKVX0pLCOP8cAyZoiYO=UyqYMJtNSV-Kt_p7xQ@mail.gmail.comSigned-off-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This reverts commit 555b1b65.

Let's try this again for 3.13.  It's required for proper
interaction with alsa.  Was disabled previously in 3.12
to be on the safe side since it caused problems on older
asics.

In order to have any realistic chance of calculating proper
ACR values, we need to be able to calculate both N and CTS,
not just CTS. We still aim for the ideal N as specified in
the HDMI spec though.

bug:
https://bugs.freedesktop.org/show_bug.cgi?id=69675Signed-off-by: NPierre Ossman <pierre@ossman.eu>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

The values were taken from the HDMI spec, but they assumed
exact x/1.001 clocks. Since we round the clocks, we also need
to calculate different N and CTS values.

Note that the N for 25.2/1.001 MHz at 44.1 kHz audio is out of
spec. Hopefully this mode is rarely used and/or HDMI sinks
tolerate overly large values of N.

bug:
https://bugs.freedesktop.org/show_bug.cgi?id=69675Signed-off-by: NPierre Ossman <pierre@ossman.eu>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Audio is enabled by default now.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Fill in gpu details for hawaii.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Uses the same code as bonaire.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This updates atombios.h with the latest changes
required for hawaii.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Set the PA_SC_RASTER_CONFIG[_1] registers for hawaii.
The rest is the same as the other asics.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This updates the CI dpm (dynamic power management)
support for hawaii.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Has same version of UVD as other CIK parts.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This just updates the firmware loading functions
to look for the appropriate firmware files for
hawaii.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

The formula needs to be adjusted since there are 4 RBs
per SH rather than 2 as on previous asics.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

The golden register settings are optimal settings for
certain registers from the hardware team.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Hawaii uses a different tiling configuration.  Add support
for it.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Skip programming a register that was removed and
adjust the mask of the VM client status.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This adds the hawaii asic specific configuration
details.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Hawaii is a new CI-based dGPU.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Spotted by Brad Smith when porting to OpenBSD.
Noticed-by: NBrad Smith <brad@comstyle.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

The new HDP flush method doesn't seem to work reliably on
sDMA either, so use the old method here too.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

To plug the VRAM memory leak (see previous patch for
details) we must unpin the frame buffer when disabling the
CRTC. This warrants the addition of disable function for legacy
CRTC, which puts the CRTC in DPMS-OFF state and unpins the
frame buffer if there is one associated with the CRTC.
Signed-off-by: NIlija Hadzic <ihadzic@research.bell-labs.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

When drm_helper_disable_unused_functions calls disable
function of the CRTC, it also sets the crtc->fb pointer
to NULL. This can later (when the mode on that CRTC is setup
again from user space) cause ***_do_set_base functions to
"think" that there is no old buffer and skip the unpinning
code. Consequently, the buffer that has been NULL-ified in
drm_helper_disable_unused_functions will never be unpinned
causing a leak in VRAM.

This patch plugs the leak by unpinning the frame buffer
in crtc_disable function.
Signed-off-by: NIlija Hadzic <ihadzic@research.bell-labs.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

The current code writing SADs to the audio registers seems to assume
that there is at most a single SAD per audio format.

However, that is not the case. Especially for PCM it is somewhat common
for sinks to have two SADs, one for 8-channel and one for 2-channel
audio, which may have different supported sample rates (i.e. the sink
supports stereo audio at higher sample rates than multichannel audio).

Because of this, only the 2-channel SAD may be used if it appears before
the 8-channel SAD. Unless other SADs require otherwise, this may cause
the ALSA HDA driver to allow stereo playback only.

Fix the code to pick the PCM SAD with the highest number of channels,
while merging the rate masks of PCM SADs with lower amount of channels
into the additional stereo rate mask byte.

Technically there are even more cases to handle (multiple non-PCM SADs
of the same type, more than two PCM SADs with varying channel counts,
etc), but those have not actually been encountered in the field and
handling them would be non-trivial.

Example affected EDID from Onkyo TX-SR674 specifying 192kHz stereo
support and 96kHz 8-channel support (and other 8-channel compressed
formats):
00ffffffffffff003dcb010000000001
ffff0103800000780a0dc9a057479827
12484c00000001010101010101010101
010101010101011d8018711c1620582c
2500c48e2100009e011d007251d01e20
6e285500c48e2100001e000000fc0054
582d53523637342020202020000000fd
00313d0f2e08000a202020202020019b
02032f724f8504030f0e07069413121e
1d1615012f097f070f1f071707503707
503f07c0834f000066030c00ffff808c
0ad08a20e02d10103e9600c48e210000
18011d80d0721c1620102c2580c48e21
00009e011d00bc52d01e20b8285540c4
8e2100001e8c0ad090204031200c4055
00c48e210000180000000000000000a8
Signed-off-by: NAnssi Hannula <anssi.hannula@iki.fi>
Tested-by: NAndre Heider <a.heider@gmail.com>
Cc: Rafał Miłecki <zajec5@gmail.com>
Acked-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Reported-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

HW engineers have listened and given us again a real interrupt with
masking and status regs. Yay!

For consistency with other platforms call the #define FIFO_UNDERRUN.
Eventually we also might need to have some enable/disable functions
for bdw display interrupts, but for now open-coding seems to be good
enough.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Let's cache the IMR value like on other platforms. This is needed to
implement the underrun reporting since then we'll have two places that
change the same register at runtime.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The layout of the CRC registers is the same as on hsw, only the
interrupt handling has changed a bit. So trivial to wire up, yay!
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Gives us hotplug, gmbus, dp aux and south errors (underrun
reporting!).
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Useful for dp aux to work better. Also stop enabling the port A
hotplug event - eDP panels are expected to fire that interupt and
we're not really ready to deal with them. This is consistent with how
we handle port A on ilk-hsw.

The more important bit is that we must delay the enabling of hotplug
interrupts until all the encoders are fully set up. But we need irq
support earlier than that, hence hotplug interrupts can only be
enabled in the ->hpd_irq_setup callback.

v2: Drop the _HOTPLUG, it isn't (Ville).

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

- Pipe underrun can't just be enabled, we need some support code like
  on ilk-hsw to make this happen. So drop it for now.
- CRC error is a special mode of the CRC hardware that we don't use,
  so again drop it. Real CRC support for bdw will be added later.
- All the other error bits are about faults, so rename the #define and
  adjust the output.

v2: Use pipe_name as pointed out by Ville. Ville's comment was on a
previous patch, but it was easier to squash in here.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>