Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since mwifiex_ds_misc_subsc_evt is used in an asynchronous case,
store the structure in the long-lived mwifiex_private instead of
on the calling stack.

This fixes a problem where the response of the asynchronous
operation would corrupt a stack frame potentially in use by
a different thread.
Signed-off-by: NJeff Disher <disher@chromium.org>
Reviewed-by: NSam Leffler <sleffler@chromium.org>
Tested-by: NJeff Disher <disher@chromium.org>
Acked-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This change adds callback for nl80211 testmode, which can be used
for testing and debugging purposes with driver and firmware.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Added usb device id to list of supported devices. 43143 is a new
802.11n single stream device.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Added usb device id to list of supported devices. 43242 is the new
802.11n 2x2 MIMO device.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

BCM43241 is an 11abg and 2x2 11n Wifi/BT/FM combo chip that
supports 40MHz channel width. This patch intends to enable
the driver support for the chip through SDIO bus interface.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

brcmf_usb_tx_ctlpkt sends message using brcmf_usb_send_ctl then
clears boolean and waits for boolean to be set (by another
thread). This can result in situation where flag gets cleared
while result was already received. First clearing the flag and
then sending the data will prevent this.

Reviewed-by: Arend Van Spriel (arend@broadcom.com)
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The TX filter bit for a station would be set by the HW
when a frame is not acked. A frame would be completed with
ATH9K_TXERR_FILT status only when the corresponding filter bit
for the destination station is already set.

Currently, un-acknowledged  packets are added to the pending queue
and retried, but the "clear_dest_mask" bit in the descriptor is
set only when the TX status has been ATH9K_TXERR_FILT. This results
in packet loss and the log shows:

wlan0: dropped TX filtered frame, queue_len=0 PS=0 @4309746071
wlan0: dropped TX filtered frame, queue_len=0 PS=0 @4309746076
wlan0: dropped TX filtered frame, queue_len=0 PS=0 @4309746377
...
...

This issue can be resolved by making sure that the destination
mask is cleared when the packet is being retried and the earlier
TX status is ATH9K_TXERR_XRETRY.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove pointless conditional before kfree_skb().
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove pointless conditional before kfree_skb().
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use is_zero_ether_addr() instead of directly using memcmp() to
determine if the ethernet address is all zeros.

Cc: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds support for parsing rates from cfg80211_ap_settings
of start_ap handler. This in turn adds support for 11a and 11b phy
configurations.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKiran Divekar <dkiran@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We should not disable "cmd_node->wait_q_enabled" flag here before
calling mwifiex_insert_cmd_to_free_q() because we want to wake up
the thread waiting for command completion inside this function.

The wait_q_enabled flag will be disabled internally upon command
completion.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKiran Divekar <dkiran@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If "iw connect" command is fired for station interface, when
heavy traffic is running on AP interface, internal scan operation
performed before actual association is aborted. In this case we
missed to release semaphore.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKiran Divekar <dkiran@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

From: Wei Yongjun <yongjun_wei@trendmicro.com.cn>

Remove duplicated include.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

From: Wei Yongjun <yongjun_wei@trendmicro.com.cn>

Remove duplicated include.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Using is_broadcast_ether_addr() instead of directly use
memcmp() to determine if the ethernet address is broadcast
address.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Using is_broadcast_ether_addr() instead of directly use
memcmp() to determine if the ethernet address is broadcast
address.

spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Assign the MCI BT state locally, rather than unnecessarily calling
ar9003_mci_state and updating it.
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Using is_zero_ether_addr() instead of directly use
memcmp() to determine if the ethernet address is all
zeros.

spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Using is_broadcast_ether_addr() instead of directly use
memcmp() to determine if the ethernet address is broadcast
address.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Using is_zero_ether_addr() and is_broadcast_ether_addr() instead of
directly use memcmp() to determine if the ethernet address is all zeros.

spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Using is_zero_ether_addr() instead of directly use
memcmp() to determine if the ethernet address is all
zeros.

spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Using is_zero_ether_addr() instead of directly use
memcmp() to determine if the ethernet address is all
zeros.

spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Using is_zero_ether_addr() and is_broadcast_ether_addr() instead of
directly use memcmp() to determine if the ethernet address is all zeros.

spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Using is_zero_ether_addr() and is_broadcast_ether_addr() instead of
directly use memcmp() to determine if the ethernet address is all zeros.

spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is not necessary to hold the firmware memory during the whole
driver lifetime, and obviously it does waste memory. Suppose there
are 4 ath9k-htc usb dongles working, kernel has to consume about
4*50KBytes RAM to cache firmware for all dongles. After applying the
patch, kernel only caches one single firmware image in RAM for
all ath9k-htc devices just during system suspend/resume cycle.

When system is ready for loading firmware, ath9k-htc can request
the loading from usersapce. During system resume, ath9k-htc still
can load the firmware which was cached in kernel memory before
system suspend.

Cc: ath9k-devel@lists.ath9k.org
Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com>
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: NMing Lei <ming.lei@canonical.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

bcma_scan_bus allocates a bcma_core for each core found on the bus, but the
memory for cores handled by the bcma driver itself was not being freed when
the bus was unregistered. This patch adds special handling for the PCIE,
MIPS, and GBIT COMMON cores, to ensure that their memory allocation is
freed as well.

Note that this patch doesn't address the memory allocated for the CC core,
as that was corrected in my previous patch "bcma: register cc core driver,
device."

Cc: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: NSaul St. John <saul.stjohn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

checkpatch pointed out an issue, fix it.
Signed-off-by: NHila Gonen <hila.gonen@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

No one uses it.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Reviewed-by: NAmit Beka <amit.beka@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Tracing commands builds an array of trace data
items even when the tracepoint is disabled.
Instead, loop in the tracepoint assignment.

This reduces overhead if tracing is compiled
into the driver but not enabled and slightly
reduces overall driver size as well:

   text	   data	    bss	    dec	    hex	filename
 114514	   6509	     48	 121071	  1d8ef	before/iwlwifi.ko
 114189	   6509	     48	 120746	  1d7aa	after/iwlwifi.ko
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: NMax Stepanov <Max.Stepanov@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Since the firmware will give us an A-MPDU bit and
only a single PHY information packet for all the
subframes in an A-MPDU, we can easily report the
minimal A-MPDU information for radiotap.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The wext code checks is the event data is within size limits.
When this check fails a message is logged with violating size.
This patch adds the event id to put us on the right track for
resolving that violation.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Doing so creates warnings, but the function is internal and
not part of the 802.11 docbooks, so it from kerneldoc.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Signed-off-by: NRobert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Using list_move_tail() instead of list_del() + list_add_tail().
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The device only supports a maximum of three
antennas, and only three bits are used, the
fourth bit is the A-MPDU indicator.

The only consequence of this is reporting
invalid information in radiotap, so this
isn't an important change.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>