OMAP5, DRA7, AM43xx all have OPPs. So select the same to allow SoC
only configuration boot to work with OPP.
Reported-by: NNikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

SOC_DRA7XX was under wrong menu within Kconfig file, which prevented
DRA7XX only build. Fixed the kconfig options for this SoC as we are
there. voltage.c needs to be added to the DRA7XX build also, otherwise
DRA7XX only build will fail.
Signed-off-by: NTero Kristo <t-kristo@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

We can now boot with device tree and appended DTB
with basic devices working. If people are still using
this board, patches are welcome to add more complete
support.
Signed-off-by: NTony Lindgren <tony@atomide.com>

The old 2420 based H4 is probably not used at all as 2420
was Nokia specific SoC. I have one, but I'm not using it because
of it's large size, and I doubt anybody else is using it either.

We do have minimal omap2420-h4.dts in place, so if anybody wants
more support on H4, patches are welcome.

So let's just remove it as that helps us making mach-omap2 to
be device tree only.
Signed-off-by: NTony Lindgren <tony@atomide.com>

Device Tree support for IGEP boards in mainline is almost
finished. The only remaining bits are support for the
Marvell SD8686 wifi + BT and TFP410 DVI chips.

Adding support for these should be straightforward so let's
not block OMAP3 moving to Device Tree only boot and remove
the board file for IGEP boards.
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NTony Lindgren <tony@atomide.com>

We now have pretty decent device tree based support for
zoom platforms. It's not complete, but basics work for
me so adding more features should be quite trivial.

Looks like also 3630 sdp is zoom based, and looking
at it's board file should also be trivial to support
with the device tree based booting.

Patches are welcome if people are still using these.
Signed-off-by: NTony Lindgren <tony@atomide.com>

We now have pretty decent support with the device tree
based booting. Patches to add more features are welcome.
Signed-off-by: NTony Lindgren <tony@atomide.com>

Delete board file for Nokia RM-680/RM-696 (N950/N9). DT-based booting
should be used for further development on this HW.
Signed-off-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NTony Lindgren <tony@atomide.com>

CLKDEV_LOOKUP selects HAVE_CLK and COMMON_CLK selects CLKDEV_LOOKUP. So
all symbols that select at least two of these symbols can be simplified.

For imx, omap2 and ux500 some rearrangements were necessary before the
simplification.
Acked-by: NTony Lindgren <tony@atomide.com>
Acked-by: NStephen Boyd <sboyd@codeaurora.org>
Acked-by: NDinh Nguyen <dinguyen@altera.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NPawel Moll <pawel.moll@arm.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NOlof Johansson <olof@lixom.net>

We are moving to device tree based booting, so board-generic
should always be built.
Signed-off-by: NTony Lindgren <tony@atomide.com>

Fix the option description to match the other TI SoCs.
This is just a cosmetic change.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: NJavier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Now that all the needed pieces for DRA7 based SoCs' is present, enable
the build support in omap2plus_defconfig
Signed-off-by: NR Sricharan <r.sricharan@ti.com>
Signed-off-by: NRajendra Nayak <rnayak@ti.com>

All of OMAP5 timer support for clocksource and clockevent is completely
reused across DRA7.
Signed-off-by: NR Sricharan <r.sricharan@ti.com>
Signed-off-by: NRajendra Nayak <rnayak@ti.com>

Avoids the following warning when SMP is off:

warning: (ARCH_KEYSTONE && SOC_OMAP5) selects ARM_ERRATA_798181 which
has unmet direct dependencies (CPU_V7 && SMP)
Reported-by: NEmilio López <emilio@elopez.com.ar>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

"ARM: OMAP: build mach-omap code only if needed" moved around the
ARCH_OMAP2PLUS stanza, but accidentally dropped the seleciton of
TI_PRIV_EDMA in the process. Add it back.

Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

If we build a kernel with CONFIG_ARCH_OMAP2PLUS enabled but all of the
individual SoCs disabled, we run into a large number of link errors
because if incorrect dependencies:

arch/arm/mach-omap2/built-in.o: In function `_add_initiator_dep':
arch/arm/mach-omap2/omap_hwmod.c:691: undefined reference to `clkdm_add_sleepdep' arch/arm/mach-omap2/built-in.o: In function `_del_initiator_dep':
arch/arm/mach-omap2/omap_hwmod.c:720: undefined reference to `clkdm_del_sleepdep' arch/arm/mach-omap2/built-in.o: In function `_enable':
arch/arm/mach-omap2/omap_hwmod.c:2145: undefined reference to `clkdm_in_hwsup'
arch/arm/mach-omap2/omap_hwmod.c:2147: undefined reference to `clkdm_hwmod_enable'
arch/arm/mach-omap2/omap_hwmod.c:2191: undefined reference to `clkdm_hwmod_disable'
arch/arm/mach-omap2/omap_hwmod.c:2146: undefined reference to `clkdm_missing_idle_reporting' arch/arm/mach-omap2/built-in.o: In function `_idle':
arch/arm/mach-omap2/omap_hwmod.c:2235: undefined reference to `clkdm_hwmod_disable' arch/arm/mach-omap2/built-in.o: In function `_shutdown':
arch/arm/mach-omap2/omap_hwmod.c:2338: undefined reference to `clkdm_hwmod_disable' arch/arm/mach-omap2/built-in.o: In function `omap_hwmod_get_context_loss_count':
arch/arm/mach-omap2/omap_hwmod.c:4071: undefined reference to `pwrdm_get_context_loss_count' arch/arm/mach-omap2/built-in.o: In function `omap_pm_clkdms_setup':
arch/arm/mach-omap2/pm.c:114: undefined reference to `clkdm_allow_idle'
arch/arm/mach-omap2/pm.c:117: undefined reference to `clkdm_sleep' arch/arm/mach-omap2/built-in.o: In function `omap2_common_pm_late_init':
arch/arm/mach-omap2/pm.c:294: undefined reference to `omap_voltage_late_init' arch/arm/mach-omap2/built-in.o: In function `omap2_gpio_dev_init':
arch/arm/mach-omap2/gpio.c:133: undefined reference to `pwrdm_can_ever_lose_context'

We can avoid this if we make CONFIG_ARCH_OMAP2PLUS a silent option that
gets enabled any time that one of the SoC versions is enabled.

Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

These are selected by omap4 but used in common omap4/5
SMP code, so building an omap5-only kernel is actually
broken without this patch.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Cc: Tony Lindgren <tony@atomide.com>

ARM errata 798181 is applicable for OMAP5 based devices. So enable
the same in the build. Errata extract and workaround information
is as below.

On Cortex-A15 (r0p0..r3p2) the TLBI*IS/DSB operations are not
adequately shooting down all use of the old entries. The
ARM_ERRATA_798181 option enables the Linux kernel workaround
for this erratum which sends an IPI to the CPUs that are running
the same ASID as the one being invalidated.

Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Now that the TWD doesn't rely on the local timer API, OMAP can
stop selecting it in Kconfig and relying on the config option to
decide if it should call smp_twd functions.
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Acked-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

Separate the smp_twd timers from the local timer API. This will
allow us to remove ARM local timer support in the near future and
gets us closer to moving this driver to drivers/clocksource.
Tested-by: NMark Rutland <mark.rutland@arm.com>
Acked-by: NMarc Zyngier <marc.zyngier@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

Enable TI EDMA option on OMAP and TI_PRIV_EDMA
Signed-off-by: NMatt Porter <mporter@ti.com>
Signed-off-by: NJoel A Fernandes <joelagnel@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Bandgap is a device used to measure temperature on electronic
equipments.  It is widely used in digital integrated circuits.  It is
based on the dependency between silicon voltage and temperature.

This patch introduce HAS_BANDGAP config entry.  This config is a boolean
value so that arch code can flag if they feature a bandgap device.

This config entry follows the same idea behind ARCH_HAS_CPUFREQ.

Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-omap@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: NFabio Stevam <festevam@gmail.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Acked-by: NAmit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: NEduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Build pieces that could be reused for AM43x - GIC related, secure
related and common PRCM.
Signed-off-by: NAfzal Mohammed <afzal@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Kconfig for AM43x (Cortex A9) family of SoC's.
Signed-off-by: NAfzal Mohammed <afzal@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

We can now boot with devicetree and muxing can be done
with pinctrl-single.c.
Signed-off-by: NTony Lindgren <tony@atomide.com>

We can now boot with device tree. If you don't want to update u-boot,
you can boot with appended DTB with the following instructions:

1. Make sure you have the appended DTB support in .config

   CONFIG_ARM_APPENDED_DTB=y
   CONFIG_ARM_ATAG_DTB_COMPAT=y
   CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_EXTEND=y

2. Build the zImage

   $ ARCH=arm CROSS_COMPILE=... make zImage

3. Build the device tree blobs

   $ ARCH=arm CROSS_COMPILE=... make dtbs

4. Append the correct panda dtb to zImage

   Depending on your hardware it's omap4-panda.dtb, omap4-panda-a4.dtb
   or omap4-panda-es.dtb.

   $ cat arch/arm/boot/zImage arch/arm/boot/dts/omap4-panda-es.dtb > /tmp/appended

5. Use mkimage to produce the appended device tree uImage

   $ mkimage -A arm -O linux -T kernel -C none -a 0x80008000 -e 0x80008000 \
     -n "Linux" -d /tmp/appended /tmp/uImage

Signed-off-by: Tony Lindgren <tony@atomide.com

We can now boot with device tree. If you don't want to update u-boot,
you can boot with appended DTB with the following instructions:

1. Make sure you have the appended DTB support in .config

   CONFIG_ARM_APPENDED_DTB=y
   CONFIG_ARM_ATAG_DTB_COMPAT=y
   CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_EXTEND=y

2. Build the zImage

   $ ARCH=arm CROSS_COMPILE=... make zImage

3. Build the device tree blobs

   $ ARCH=arm CROSS_COMPILE=... make dtbs

4. Append the dtb to zImage

   $ cat arch/arm/boot/zImage arch/arm/boot/dts/omap4-sdp.dtb > /tmp/appended

5. Use mkimage to produce the appended device tree uImage

   $ mkimage -A arm -O linux -T kernel -C none -a 0x80008000 -e 0x80008000 \
     -n "Linux" -d /tmp/appended /tmp/uImage
Signed-off-by: NTony Lindgren <tony@atomide.com>

Commit 8a6201b9 (ARM: OMAP2+: Fix unmet direct dependencies for zoom
for 8250 serial) fixed unmet direct dependencies for 8250, but failed
to do the same for omap serial. This can cause the following warning:

warning: (ARCH_OMAP2PLUS_TYPICAL) selects SERIAL_OMAP which has
unmet direct dependencies (TTY && HAS_IOMEM && GENERIC_HARDIRQS &&
ARCH_OMAP2PLUS).

We should not select drivers, they should be selected by the
user. Fix the issue by removing the select and adding them to
omap2plus_defconfig instead.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

CONFIG_ARCH_OMAP2PLUS depends on (ARCH_MULTI_V6 || ARCH_MULTI_V7) as of
a0694861 "ARM: OMAP2+: Enable ARCH_MULTIPLATFORM support", but the
individual OMAP2/3/4/5 and AM33XX platforms can all be selected independent
of what we are building for, which is a bug and prevents us from easily
building e.g. an ARMv7-only defconfig.

This makes ARCH_OMAP2 depend on ARCH_MULTI_V6 and the others depend on
ARCH_MULTI_V7, to ensure we really only build the platforms for the
CPUs we have enabled in the global multiplatform configuration step.

Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

The TWD and SCU configs are selected by default as long as
MSM_SCORPIONMP is false and/or MCT is false. Implementing the
logic this way certainly saves lines in the Kconfig but it
precludes those machines which select MSM_SCORPIONMP or MCT from
participating in the single zImage effort because when those
machines are combined with other SMP capable machines the TWD and
SCU are no longer selected by default.

Push the select out to the machine entries so that we can compile
these machines together and still select the appropriate configs.

Cc: Barry Song <baohua.song@csr.com>
Acked-by: NDavid Brown <davidb@codeaurora.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Acked-by: NPawel Moll <pawel.moll@arm.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Acked-by: NSimon Horman <horms@verge.net.au>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: NViresh Kumar <viresh.linux@gmail.com>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

This enables the fixes for the below erratas
applicable for OMAP4 Socs.

754322: Faulty MMU translations following ASID switch

775420: A data cache maintenance operation which aborts,
        followed by an ISB, without any DSB in-between,
        might lead to deadlock
Signed-off-by: NSricharan R <r.sricharan@ti.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

In some situations it is useful for userspace to
know some SoC-specific information. For example,
this may be used for deciding what kernel module to
use or how to better configure some settings etc.
This patch exports OMAP SoC information to userspace
using existing in Linux kernel SoC infrastructure.

This information can be read under
/sys/devices/socX directory
Signed-off-by: NRuslan Bilovol <ruslan.bilovol@ti.com>
[tony@atomide.com: updated for multiplatform changes]
Signed-off-by: NTony Lindgren <tony@atomide.com>

Errata i688 is also applicable for OMAP5 based devices. Update the
code so that it can be enabled on OMAP5 devices.
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>

We should not select drivers from kconfig as they should by default
be optional. Otherwise we'll be chasing broken dependencies forever:

warning: (MACH_OMAP_ZOOM2 && MACH_OMAP_ZOOM3 && MWAVE) selects SERIAL_8250
which has unmet direct dependencies (TTY && HAS_IOMEM && GENERIC_HARDIRQS)

Fix the issue by removing the selects for zoom and add them to
omap2plus_defconfig.
Reported-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NTony Lindgren <tony@atomide.com>

As apollon board doesn't used anymore, remove it.
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
[tony@atomide.com: dropped uncompress.h changes, it's gone]
Signed-off-by: NTony Lindgren <tony@atomide.com>

The core functionality of the arch_timer driver is not directly tied to
anything under arch/arm, and can be split out.

This patch factors out the core of the arch_timer driver, so it can be
shared with other architectures. A couple of functions are added so
that architecture-specific code can interact with the driver without
needing to touch its internals.

The ARM_ARCH_TIMER config variable is moved out to
drivers/clocksource/Kconfig, existing uses in arch/arm are replaced with
HAVE_ARM_ARCH_TIMER, which selects it.
Signed-off-by: NMark Rutland <mark.rutland@arm.com>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Acked-by: NMarc Zyngier <marc.zyngier@arm.com>

Flip on multiplatform support for omap2+.

No changes to omap2plus_defconfig needed, but please note
that you may need to update your custom config files to
make sure you have:

CONFIG_ARCH_MULTIPLATFORM=y
CONFIG_ARCH_MULTI_V7=y
CONFIG_ARCH_OMAP2PLUS=y

And may need CONFIG_ARCH_MULTI_V6=y if booting omap2 boards.

Cc: Russell King <linux@arm.linux.org.uk>
Tested-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

We still need to fix up few places for multiplatform support,
but that can proceed separately. Fix the issue by making the
problem drivers depends !ARCH_MULTIPLATFORM for now.

The remaining pieces that are not multiplatform compatible
for omap2+ SoCs are:

1. Some drivers are using custom omap_dm_timer calls

There are two drivers that are directly usign omap hardware
timers for PWM and DSP clocking: drivers/media/rc/ir-rx51.c and
drivers/staging/tidspbridge/core/dsp-clock.c. These can be
fixed for multiplatform by allowing a minimal set of hardware
timers to be accessed, and for some functionality by using the
hrtimer framework.

2. Hardware OMAP4_ERRATA_I688 needs to be fixed up

This can't be enabled for multiplatform configurations in
it's current form. It may be possible to fix it up to do
instruction replacement early on during init. Luckily it
looks like this errata does not seem to get hit with
mainline kernel code alone at least currently.

3. Legacy header needed for omap-sham.c

Looks like it still needs mach/irqs.h for omap1 that
does not exist for multiplatform systems. Just ifdef
it for now.

4. Mailbox is waiting to get moved to drivers

Disable it for now to avoid adding a dependency to the
mailbox patches.

Cc: Timo Kokkonen <timo.t.kokkonen@iki.fi>
Cc: Sean Young <sean@mess.org>
Cc: "Víctor Manuel Jáquez Leal" <vjaquez@igalia.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Omar Ramirez Luna <omar.ramirez@ti.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
[tony@atomide.com: updated to disable mailbox]
Signed-off-by: NTony Lindgren <tony@atomide.com>

In commit fa6d79d2 (ARM: OMAP: Add initialisation for the real-time
counter), the function realtime_counter_init() was added. However, if
the kernel configuration option CONFIG_SOC_OMAP5 is not selected then
the following compiler warning is observed.

  CC      arch/arm/mach-omap2/timer.o
  arch/arm/mach-omap2/timer.c:489:20: warning: ‘realtime_counter_init’
  defined but not used [-Wunused-function]

Commit fa6d79d2 also introduced the kernel configuration option
CONFIG_SOC_HAS_REALTIME_COUNTER. If this option is not selected then the
a stub function for realtime_counter_init() is defined.

For non-OMAP5 devices, there is no realtime counter and so
realtime_counter_init() function and stub function are not used for
these devices. Therefore, fix this warning by only allowing the kernel
configuration option CONFIG_SOC_HAS_REALTIME_COUNTER to be enabled for
OMAP5 devices.

Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reported-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NJon Hunter <jon-hunter@ti.com>
Acked-by Santosh Shilimkar <santosh.shilimkar@ti.com>

Select COMMON_CLK for all OMAP2+ SoCs and switch over to using new
data files for OMAP2/3/4.

The older data files will get removed in subsequent patches.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: move 'select COMMON_CLK' from ARCH_OMAP2PLUS_TYPICAL to
 the per-SoC and per-"arch" Kconfig sections]
[mturquette@ti.com: fixed up #ifdef mismatch in clock.h in previous
  patch which drops that change from this patch]
Signed-off-by: NMike Turquette <mturquette@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>