In 02c958dd (net/macb: add TX multiqueue support for gem), the
initialization of tx_head and tx_tail in macb_init_rings() was moved
inside the loop that iterates over each element in the ring.  Since
tx_head and tx_tail only need to be assigned once, move them back out of
the loop.
Signed-off-by: NBen Shelton <ben.shelton@ni.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On some feature changes, driver employes an inner-reload flow where it
resets the function and re-configures it with the new required set of
parameters.

Such a flow proves fatal to any VF since those were not intended to be used
while HW is being reset underneath, causing them [at best] to lose all
connectivity.

This changes driver behavior to fail all configuration changes [e.g., mtu
change] requested of the driver in case VFs are active.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

HSU_DMA is selected by the HSU_DMA_PCI driver, this should be user selected
so remove the user prompt for this
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently we parse max_msg_sz from the wrong offset in QUERY_DEV_CAP,
fix to use the right offset.

Fixes: 0b131561 ('net/mlx4_en: Add Flow control statistics [..]')
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The only reason to keep parisc's private asm/scatterlist.h was that it
had the macro sg_virt_addr().  Convert all callers to use something else
(sometimes just sg->offset was enough, others should use sg_virt()), and
we can just use the asm-generic scatterlist.h instead.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NDave Anglin <dave.anglin@bell.net>
Signed-off-by: NHelge Deller <deller@gmx.de>

My 'allmodconfig' build is _almost_ free of warnings, and most of the
remaining ones are for legacy drivers that just do bad things that I
can't find it in my black heart to care too much about.  But this one
was just annoying me:

   drivers/media/v4l2-core/videobuf2-core.c:3256:26: warning: unused variable ‘fileio’ [-Wunused-variable]

because commit 0e661006 ("[media] vb2: fix 'UNBALANCED' warnings
when calling vb2_thread_stop()") removed all users of 'fileio' and
instead calls "__vb2_cleanup_fileio(q)" to clean up q->fileio.  But the
now unused 'fileio' variable was left around.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The Error-Bit on the avalon streaming interface of the
tx-dma-channel was always set. In SGMII configurations
this leads to error-symbols on the PCS and packet-rejection
on the receiver side (e.g. SGMII/1000Base-X connected switch).

This only applies to the tse-configuration with MSGDMA.

This issue was detected and fixed on a custom board with
a direct connection to a Marvell switch in SGMII-PHY-Mode.
(incl. custom patches for SGMII-PCS).

According to the datasheet if ff_tx_err (avalon-streaming)
is set it is forwarded to gm_tx_err. As a result the PCS
is forwarding the error by sending a "/V/"-caracter.
Signed-off-by: NAndreas Oetken <ennoerlangen@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Minor, use the explicit PORT_DEFAULT_VLAN define instead of 0x07.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mv88e6xxx_setup_port_common was writing to PORT_DEFAULT_VLAN (port
offset 0x07) instead of PORT_CONTROL_1 (port offset 0x05).

Fixes: cca8b133 ("net: dsa: Use mnemonics rather than register numbers")
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Call checksum_complete_unset in PPP receive to discard checksum-complete
value. PPP does not pull checksum for headers and also modifies packet
as in VJ compression.
Signed-off-by: NTom Herbert <tom@herbertland.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A pppoe session is identified by its session ID and MAC address.
Currently pppoe does not check if the received pkg has the correct
MAC address. This is a problem when the eth I/F is in promisc mode
as then any DST MAC address is accepted.
Signed-off-by: NJoakim Tjernlund <joakim.tjernlund@transmode.se>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

My Pengutronix address is not valid anymore, redirect people to the
Pengutronix kernel team.
Reported-by: NHarald Geyer <harald@ccbib.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Acked-by: NRobert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The suspend scan rate value should not exceed 1000, unfortunately when
implementing the limit we used max_t instead of min_t, causing the value to
be at least 1000.
Signed-off-by: NDudley Du <dudl@cypress.com>
Reviewed-by: NBenson Leung <bleung@chromium.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

According to Elan's firmware engineers we should not be subtracting 1 form
the raw number of x and y traces so that the pitch size is correct. For
example, if the touchpad x resolution is 2800 and x trace number is 20,
the pitch size of x should be 2800/20 = 140, not 2800/19 = 147.36.
Signed-off-by: NDuson Lin <dusonlin@emc.com.tw>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

When hover is detected report ABS_MT_DISTANCE as 1; for active contacts
the distance is reported as 0.
Signed-off-by: NDuson Lin <dusonlin@emc.com.tw>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Let's zero-extend hardware id number when forming firmware file name,
to avoid kernel requesting firmware like "elants_i2c_   0.bin", which
is quite unexpected.

Acked-by: Charlie Mooney<charliemooney@chromium.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Add handling of missed events in omap_dss_pm_notif which are
needed to support hibernation (suspend to disk).
Signed-off-by: NGrygorii Strashko <Grygorii.Strashko@linaro.org>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

We don't need VT switch when suspending/resuming, so disable it. This
speeds up suspend/resume.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Cc: NeilBrown <neil@brown.name>

Replace occurences of the pci api by appropriate call to the dma api.

A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr)

@deprecated@
idexpression id;
position p;
@@

(
  pci_dma_supported@p ( id, ...)
|
  pci_alloc_consistent@p ( id, ...)
)

@bad1@
idexpression id;
position deprecated.p;
@@
...when != &id->dev
   when != pci_get_drvdata ( id )
   when != pci_enable_device ( id )
(
  pci_dma_supported@p ( id, ...)
|
  pci_alloc_consistent@p ( id, ...)
)

@depends on !bad1@
idexpression id;
expression direction;
position deprecated.p;
@@

(
- pci_dma_supported@p ( id,
+ dma_supported ( &id->dev,
...
+ , GFP_ATOMIC
  )
|
- pci_alloc_consistent@p ( id,
+ dma_alloc_coherent ( &id->dev,
...
+ , GFP_ATOMIC
  )
)
Signed-off-by: NQuentin Lambert <lambert.quentin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, iflink of the parent interface was always accessed, even
when interface didn't have a parent and hence we crashed there.

Handle the interface types properly: for a child interface, return
the ifindex of the parent, for parent interface, return its ifindex.

For child devices, make sure to set the parent pointer prior to
invoking register_netdevice(), this allows the new ndo to be called
by the stack immediately after the child device is registered.

Fixes: 5aa7add8 ('infiniband/ipoib: implement ndo_get_iflink')
Reported-by: NHonggang Li <honli@redhat.com>
Signed-off-by: NErez Shitrit <erezsh@mellanox.com>
Signed-off-by: NHonggang Li <honli@redhat.com>
Reviewed-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>+
Acked-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/net/ethernet/sfc/selftest.c: In function ‘efx_iterate_state’:
drivers/net/ethernet/sfc/selftest.c:388:9: warning: passing argument 1 of ‘memcpy’ discards ‘const’ qualifier from pointer target type [-Wdiscarded-array-qualifiers]

This is because the msg[] member of struct efx_loopback_payload
is marked as 'const'.  Remove that.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix bug which occurs when more than <limit> packets are available during
napi-poll, leading to "delays" and retransmissions on the network.

Check for (count < limit) before checking the get_rx_status in tse_rx-function.
Function get_rx_status is reading from the response-fifo.
If there is currently a response in the fifo,
reading the last byte of the response pops the value from the fifo.
If the limit is checked as second condition
and the limit is reached the fifo is popped but the packet is not processed.
Signed-off-by: NAndreas Oetken <ennoerlangen@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In commit 04ffcb25 ("net: Add ndo_gso_check") Tom originally
added the 'dev' argument to be able to call ndo_gso_check().

Then later, when generalizing this in commit 5f35227e
("net: Generalize ndo_gso_check to ndo_features_check")
Jesse removed the call to ndo_gso_check() in netif_needs_gso()
by calling the new ndo_features_check() in a different place.
This made the 'dev' argument unused.

Remove the unused argument and go back to the code as before.

Cc: Tom Herbert <therbert@google.com>
Cc: Jesse Gross <jesse@nicira.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When you redirect a VLAN device to any device, you end up with
crap in af_packet on the xmit path because hard_header_len is
not equal to skb->mac_len.  So the redirected packet contains
four extra bytes at the start which then gets interpreted as
part of the MAC address.

This patch fixes this by only pushing skb->mac_len.  We also
need to fix ifb because it tries to undo the pushing done by
act_mirred.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Acked-by: NAlexei Starovoitov <ast@plumgrid.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mvsas is giving a General protection fault when it encounters an expander
attached ATA device.  Analysis of mvs_task_prep_ata() shows that the driver is
assuming all ATA devices are locally attached and obtaining the phy mask by
indexing the local phy table (in the HBA structure) with the phy id.  Since
expanders have many more phys than the HBA, this is causing the index into the
HBA phy table to overflow and returning rubbish as the pointer.

mvs_task_prep_ssp() instead does the phy mask using the port properties.
Mirror this in mvs_task_prep_ata() to fix the panic.
Reported-by: NAdam Talbot <ajtalbot1@gmail.com>
Tested-by: NAdam Talbot <ajtalbot1@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

On systems with shared interrupts the interrupt routine might
be called as soon as the interrupt is enabled.
As this might happen before pci_set_drvdata() is called the
system would crash.
Reported-by: NAndreas Brogle <anbro@ok.de>
Tested-by: NAndreas Brogle <anbro@ok.de>
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Change the __raw IO calls to readl/write_relaxed which makes the driver
endian agnostic to run properly on big endian systems.
Signed-off-by: NBen Dooks <ben.dooks@codethink.co.uk>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Andrew Victor <linux@maxim.org.za>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The RTC driver supports two flavors of S5M devices: S5M8767-like and
S2MPS14-like.

On S2MPS13 and S2MPS14 devices the RTC module is the same so we want to
re-use the existing support of S2MPS14.  However device type was passed
from parent MFD driver in platform data structure.  This way for the
S2MPS13 device the main MFD driver passed device type of 'S2MPS13X'.

Instead decouple detecting of device type between main MFD and RTC driver.
 This allows adding support for other S2MPS14 variations (like S2MPS11 and
S2MPS13) easily by adding to mfd/sec-core.c:

static const struct mfd_cell s2mps13_devs[] = {
	{ .name = "s2mps14-rtc", }
};
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

sync_buffer() needs the mmap_sem for two distinct operations, both only
occurring upon user context switch handling:

 1) Dealing with the exe_file.

 2) Adding the dcookie data as we need to lookup the vma that
   backs it. This is done via add_sample() and add_data().

This patch isolates 1), for it will no longer need the mmap_sem for
serialization.  However, for now, make of the more standard
get_mm_exe_file(), requiring only holding the mmap_sem to read the value,
and relying on reference counting to make sure that the exe file won't
dissappear underneath us while doing the get dcookie.

As a consequence, for 2) we move the mmap_sem locking into where we really
need it, in lookup_dcookie().  The benefits are twofold: reduce mmap_sem
hold times, and cleaner code.

[akpm@linux-foundation.org: export get_mm_exe_file for arch/x86/oprofile/oprofile.ko]
Signed-off-by: NDavidlohr Bueso <dbueso@suse.de>
Cc: Robert Richter <rric@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Using the indenting we can see the curly braces were obviously intended.
This is a static checker fix, but my guess is that we don't read enough
bytes, because we don't calculate "t_len" correctly.

Fixes: f1d82698 ('memstick: use fully asynchronous request processing')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Cc: Alex Dubov <oakad@yahoo.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This kthread is not loop at all due to break at the end of the loop.  Make
that function linear, with no while loop.

And remove an unnecessary cast.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Cc: Anil Gurumurthy <anil.gurumurthy@qlogic.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Neaten the logging a bit by adding #define pr_fmt

Miscellanea:

o Remove __FILE__/__func__ uses
o Coalesce formats adding missing spaces
o Align arguments
o (rtc-cmos) Integrated 2 consecutive messages
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The hym8563 datasheet describes the clock output control-bit as "when set
to logic 0, the square wave output is enable, when set to logic 1, the
CLKOUT output is inhibited".  But in reality the setting is exactly
opposite.

Before now, the clock output was not really used, but on the rk3288 soc
this generated clock is used to supply the temperature sensor block and
the swapped bit value prevented it from working.  With the corrected
value, the tsadc now reports correct values.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

s3c_rtc_gettime() already returns the result of rtc_valid_tm() on the
obtained time so get rid of another call to rtc_valid_tm().
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: NChanwoo Choi <cw00.choi@samsung.com>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

module_platform_driver_probe() prevents driver from requesting probe
deferral.  So using module_platform_drive() to support probe deferral.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

RTC is present in AM43xx and DRA7xx also.  Updating the Kconfig to depend
on ARCH_OMAP or ARCH_DAVINCI
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

RTC module contains a kicker mechanism to prevent any spurious writes from
changing the register values.  This mechanism requires two MMR writes to
the KICK0 and KICK1 registers with exact data values before the kicker
lock mechanism is released.

Currently the driver release the lock in the probe and leaves it enabled
until the rtc driver removal.  This eliminates the idea of preventing
spurious writes when RTC driver is loaded.  So implement rtc lock and
unlock functions before and after register writes.

This is as advised by Paul to implement lock and unlock functions in the
driver and not to unlock and leave it in probe.  The same discussion can
be seen here:
http://www.mail-archive.com/linux-omap%40vger.kernel.org/msg111588.htmlSigned-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Initialize the device time (if it is wrong) before registering RTC device
to fix following error message during rtc-s3c probe:

[    2.215414] rtc (null): read_time: fail to read
[    2.216322] s3c-rtc 10070000.rtc: rtc core: registered s3c as rtc1
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use function name in the error log instead of __FILE__.
Signed-off-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

__rtc_read_time logs should be debug logs instead of error logs.

For example, when the RTC clock is not set, it's not really useful
to print a kernel error log every time someone tries to read the clock:

	~ # hwclock -r
	[  604.508263] rtc rtc0: read_time: fail to read
	hwclock: RTC_RD_TIME: Invalid argument

If there's a real error, it's likely that lower level or higher level
code will tell it anyway. Make these logs debug logs, and also print
the error code for the read failure.
Signed-off-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>