http://bugzilla.kernel.org/show_bug.cgi?id=13312

at76_dwork_hw_scan holds a mutex while calling ieee80211_scan_completed,
which then calls at76_config which needs the same mutex.  This reworks
the ordering to not hold the lock while calling ieee80211_scan_completed.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The previous commit "convert to net_device_ops" broke the Blackfin MAC
driver as it declared the new structure before the function it used:
  CC      drivers/net/bfin_mac.o
drivers/net/bfin_mac.c:984: error: ‘bfin_mac_close’ undeclared here (not in a function)
make[1]: *** [drivers/net/bfin_mac.o] Error 1
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Both atl1.c and atl2.c include atlx.h, which defines some modinfo
stuff. But atl2.c seems like it doesn't want the modinfo data
from atlx.h, as it defines its own.

Running modinfo on atl2.ko, we get conflicting information:

$ /sbin/modinfo drivers/net/atlx/atl2.ko | egrep "version|description|author"
version:        2.2.3
description:    Atheros Fast Ethernet Network Driver
author:         Atheros Corporation <xiong.huang@atheros.com>, Chris Snook <csnook@redhat.com>
version:        2.1.3
author:         Xiong Huang <xiong.huang@atheros.com>, 	Chris Snook <csnook@redhat.com>, Jay Cliburn <jcliburn@gmail.com>

Move the modinfo data out of atlx.h and into atl1.c to eliminate
the confusion:

$ /sbin/modinfo drivers/net/atlx/atl1.ko | egrep "version|description|author"
version:        2.1.3
author:         Xiong Huang <xiong.huang@atheros.com>, 	Chris Snook <csnook@redhat.com>, Jay Cliburn <jcliburn@gmail.com>
description:    Atheros L1 Gigabit Ethernet Driver

$ /sbin/modinfo drivers/net/atlx/atl2.ko | egrep "version|description|author"
version:        2.2.3
description:    Atheros Fast Ethernet Network Driver
author:         Atheros Corporation <xiong.huang@atheros.com>, Chris Snook <csnook@redhat.com>
Reported-by: NScott Scriven <scott.scriven@hp.com>
Signed-off-by: NAlex Chiang <achiang@hp.com>
Acked-by: NJay Cliburn <jcliburn@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Gianfar interrupt handler uses IEVENT_ERR_MASK to check and handle errors.
Babbling RX error (IEVENT_BABR) should be included in IEVENT_ERROR_MASK.
Otherwise if BABR is raised, it never gets handled nor cleared, and an
interrupt storm results. This has been observed to happen on sending a
burst of ethernet frames to a gianfar based board.
Signed-off-by: NXiaotian Feng <xiaotian.feng@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 8169 chip only generates MSI interrupts when all enabled event
sources are quiescent and one or more sources transition to active. If
not all of the active events are acknowledged, or a new event becomes
active while the existing ones are cleared in the handler, we will not
see a new interrupt.

The current interrupt handler masks off the Rx and Tx events once the
NAPI handler has been scheduled, which opens a race window in which we
can get another Rx or Tx event and never ACK'ing it, stopping all
activity until the link is reset (ifconfig down/up). Fix this by always
ACK'ing all event sources, and loop in the handler until we have all
sources quiescent.
Signed-off-by: NDavid Dillow <dave@thedillows.org>
Tested-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Changeset ca17584b ("mac8390: update
to net_device_ops") broke mac8390 by adding 8390.o to the link. That
meant that lib8390.c was included twice, once in mac8390.c and once in
8390.c, subject to different macros. This patch reverts that by
avoiding the wrappers in 8390.c. They seem to be of no value since
COMPAT_NET_DEV_OPS is going away soon.

Tested with a Kinetics EtherPort card.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit 0fd56bb5 ("gianfar:
Add support for skb recycling"), gianfar puts skbuffs that are in
the rx ring back onto the recycle list as-is in case there was a
receive error, but this breaks the following invariant: that all
skbuffs on the recycle list have skb->data = skb->head + NET_SKB_PAD.

The RXBUF_ALIGNMENT realignment done in gfar_new_skb() will be done
twice on skbuffs recycled in this way, causing there not to be enough
room in the skb anymore to receive a full packet, eventually leading
to an skb_over_panic from gfar_clean_rx_ring() -> skb_put().

Resetting the skb->data pointer to skb->head + NET_SKB_PAD before
putting the skb back onto the recycle list restores the mentioned
invariant, and should fix this issue.
Reported-by: NMichael Guntsche <mike@it-loops.com>
Tested-by: NMichael Guntsche <mike@it-loops.com>
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the i2400m is connected to a network, the host interface (USB)
cannot be suspended. For that to happen, the device has to have
negotiated with the basestation to put the link on IDLE state.

If the host tries to put the device in standby while it is connected
but not idle, the device resets, as the driver should not do that.

To avoid triggering that, when the USB susbsytem requires the driver
to autosuspend the device, the driver checks if the device is not yet
idle. If it is not, the request is rejected (will be retried again
later on after the autosuspend timeout). At some point the device will
enter idle and the request will succeed (unless of course, there is
network traffic, but at that point, there is no idle neither in the
link or the host interface).
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Do not go beyond ARRAY_SIZE of intf->crypto_stats
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

enable iwl driver to support 5000 ucode having version 2 of API
Signed-off-by: NJay Sternberg <jay.e.sternberg@linux.intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

"airo: airo_get_encode{,ext} potential buffer overflow" was actually a
no-op, due to an unrecognized type overflow in an assignment.  Oddly,
gcc only seems to tell me about it when using -Wextra...grrr...
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When the EEPROM contains weird values for the power levels we have to
fix the interpolation process.
Signed-off-by: NFabio Rossi <rossi.f@inwind.it>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Calling cancel_delayed_work() from inside
spin_lock_irqsave, introduces a potential deadlock.

As explained by Johannes Berg <johannes@sipsolutions.net>

A - lock
T - timer

phase                   CPU 1           CPU 2
---------------------------------------------

some place that calls
cancel_timer_sync()
(which is the | code)
                                        lock-irq(A)
|                                       "lock-irq"(T)
|                                       "unlock"(T)
|                                       wait(T)
                                        unlock(A)

timer softirq
                        "lock"(T)
                        run(T)
                        "unlock"(T)

irq handler
          lock(A)
          unlock(A)

Now all that again, interleaved, leading to deadlock:

                                        lock-irq(A)
                        "lock"(T)
                         run(T)
IRQ during or maybe
before run(T) -->        lock(A)
                                        "lock-irq"(T)
                                        wait(T)

We fix this by moving the call to cancel_delayed_work() into workqueue.
There are cases where the work may not actually be queued or running
at the time we are trying to cancel it, but cancel_delayed_work() is
able to deal with this.

Also cleanup iwl_set_mode related to this call. This function
(iwl_set_mode) is only called when bringing interface up and there will
thus not be any scanning done. No need to try to cancel scanning.

Fixes http://bugzilla.kernel.org/show_bug.cgi?id=13224, which was also
reported at http://marc.info/?l=linux-wireless&m=124081921903223&w=2 .
Tested-by: NMiles Lane <miles.lane@gmail.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Acked-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Commit e8f055f0 ("ath5k: Update reset code") subtly changed the
code that computes floating point values for the PHY3_TIMING register
such that the exponent is off by a decimal point, which can cause
problems with OFDM channel operation.

get_bitmask_order() actually returns the highest bit set plus one,
whereas the previous code wanted the highest bit set.  Instead, use
ilog2 which is what this code is really calculating.  Also check
coef_scaled to handle the (invalid) case where we need log2(0).
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

AR5K_PHY_PLL_40MHZ_5413 should not be ORed with AR5K_PHY_MODE_RAD_RF5112
for 5 GHz channels.

The incorrect PLL value breaks scanning in the countries where 5 GHz
channels are allowed.
Signed-off-by: NPavel Roskin <proski@gnu.org>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

FIFO1_DMA_ERR is set twice, the second should be FIFO2_DMA_ERR.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Acked-by: NRam Vepa <ram.vepa@neterion.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After 2.6.29, PPC no more admits passing NULL to the dev parameter of
the DMA API. The result is a BUG followed by solid lock-up when the 
mv643xx_eth driver brings an interface up. The following patch makes 
the driver work on my Pegasos again; it is mostly a search and replace 
of NULL by mp->dev->dev.parent in dma allocation/freeing/mapping/unmapping
functions.
Signed-off-by: NGabriel Paubert <paubert@iram.es>
Acked-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

One of the purposes of bonding is to allow for redundant links, and failover
correctly if the cable is pulled. If all the members of a bonded device have
no carrier present, the bonded device itself needs to report no carrier present
to user space so management tools (like routing daemons) can respond.

Bonding in 802.3ad mode does not work correctly for this because it incorrectly
chooses a link that is down as a possible aggregator.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Mixing of normal and irq spinlocks results in the following lockdep messages
on bootup on IP32:

[...]
Sending DHCP requests .
======================================================
[ INFO: SOFTIRQ-safe -> SOFTIRQ-unsafe lock order detected ]
2.6.30-rc5-00164-g41baeef #30
------------------------------------------------------
swapper/1 [HC0[0]:SC0[1]:HE0:SE0] is trying to acquire:
 (&priv->meth_lock){+.+...}, at: [<ffffffff8026388c>] meth_tx+0x48/0x43c

and this task is already holding:
 (_xmit_ETHER#2){+.-...}, at: [<ffffffff802d3a00>] __qdisc_run+0x118/0x30c
which would create a new lock dependency:
 (_xmit_ETHER#2){+.-...} -> (&priv->meth_lock){+.+...}

but this new dependency connects a SOFTIRQ-irq-safe lock:
 (_xmit_ETHER#2){+.-...}
... which became SOFTIRQ-irq-safe at:
  [<ffffffff80061458>] __lock_acquire+0x784/0x1a14
  [<ffffffff800627e0>] lock_acquire+0xf8/0x150
  [<ffffffff800128d0>] _spin_lock+0x30/0x44
  [<ffffffff802d2b88>] dev_watchdog+0x70/0x398
  [<ffffffff800433b8>] run_timer_softirq+0x1a8/0x248
  [<ffffffff8003da5c>] __do_softirq+0xec/0x208
  [<ffffffff8003dbd8>] do_softirq+0x60/0xe4
  [<ffffffff8003dda0>] irq_exit+0x54/0x9c
  [<ffffffff80004420>] ret_from_irq+0x0/0x4
  [<ffffffff80004720>] r4k_wait+0x20/0x40
  [<ffffffff80015418>] cpu_idle+0x30/0x60
  [<ffffffff804cd934>] start_kernel+0x3ec/0x404

to a SOFTIRQ-irq-unsafe lock:
 (&priv->meth_lock){+.+...}
... which became SOFTIRQ-irq-unsafe at:
...  [<ffffffff800614f8>] __lock_acquire+0x824/0x1a14
  [<ffffffff800627e0>] lock_acquire+0xf8/0x150
  [<ffffffff800128d0>] _spin_lock+0x30/0x44
  [<ffffffff80263f20>] meth_reset+0x118/0x2d8
  [<ffffffff8026424c>] meth_open+0x28/0x140
  [<ffffffff802c1ae8>] dev_open+0xe0/0x18c
  [<ffffffff802c1268>] dev_change_flags+0xd8/0x1d4
  [<ffffffff804e7770>] ip_auto_config+0x1d4/0xf28
  [<ffffffff80012e68>] do_one_initcall+0x58/0x170
  [<ffffffff804cd190>] kernel_init+0x98/0x104
  [<ffffffff8001520c>] kernel_thread_helper+0x10/0x18

other info that might help us debug this:

2 locks held by swapper/1:
 #0:  (rcu_read_lock){.+.+..}, at: [<ffffffff802c0954>] dev_queue_xmit+0x1e0/0x4b0
 #1:  (_xmit_ETHER#2){+.-...}, at: [<ffffffff802d3a00>] __qdisc_run+0x118/0x30c

the SOFTIRQ-irq-safe lock's dependencies:
-> (_xmit_ETHER#2){+.-...} ops: 0 {
   HARDIRQ-ON-W at:
                        [<ffffffff800614d0>] __lock_acquire+0x7fc/0x1a14
                        [<ffffffff800627e0>] lock_acquire+0xf8/0x150
                        [<ffffffff800128d0>] _spin_lock+0x30/0x44
                        [<ffffffff802d2b88>] dev_watchdog+0x70/0x398
                        [<ffffffff800433b8>] run_timer_softirq+0x1a8/0x248
                        [<ffffffff8003da5c>] __do_softirq+0xec/0x208
                        [<ffffffff8003dbd8>] do_softirq+0x60/0xe4
                        [<ffffffff8003dda0>] irq_exit+0x54/0x9c
                        [<ffffffff80004420>] ret_from_irq+0x0/0x4
                        [<ffffffff80004720>] r4k_wait+0x20/0x40
                        [<ffffffff80015418>] cpu_idle+0x30/0x60
                        [<ffffffff804cd934>] start_kernel+0x3ec/0x404
   IN-SOFTIRQ-W at:
                        [<ffffffff80061458>] __lock_acquire+0x784/0x1a14
                        [<ffffffff800627e0>] lock_acquire+0xf8/0x150
                        [<ffffffff800128d0>] _spin_lock+0x30/0x44
                        [<ffffffff802d2b88>] dev_watchdog+0x70/0x398
                        [<ffffffff800433b8>] run_timer_softirq+0x1a8/0x248
                        [<ffffffff8003da5c>] __do_softirq+0xec/0x208
                        [<ffffffff8003dbd8>] do_softirq+0x60/0xe4
                        [<ffffffff8003dda0>] irq_exit+0x54/0x9c
                        [<ffffffff80004420>] ret_from_irq+0x0/0x4
                        [<ffffffff80004720>] r4k_wait+0x20/0x40
                        [<ffffffff80015418>] cpu_idle+0x30/0x60
                        [<ffffffff804cd934>] start_kernel+0x3ec/0x404
   INITIAL USE at:
                       [<ffffffff80061570>] __lock_acquire+0x89c/0x1a14
                       [<ffffffff800627e0>] lock_acquire+0xf8/0x150
                       [<ffffffff800128d0>] _spin_lock+0x30/0x44
                       [<ffffffff802d2b88>] dev_watchdog+0x70/0x398
                       [<ffffffff800433b8>] run_timer_softirq+0x1a8/0x248
                       [<ffffffff8003da5c>] __do_softirq+0xec/0x208
                       [<ffffffff8003dbd8>] do_softirq+0x60/0xe4
                       [<ffffffff8003dda0>] irq_exit+0x54/0x9c
                       [<ffffffff80004420>] ret_from_irq+0x0/0x4
                       [<ffffffff80004720>] r4k_wait+0x20/0x40
                       [<ffffffff80015418>] cpu_idle+0x30/0x60
                       [<ffffffff804cd934>] start_kernel+0x3ec/0x404
 }
 ... key      at: [<ffffffff80cf93f0>] netdev_xmit_lock_key+0x8/0x1c8

the SOFTIRQ-irq-unsafe lock's dependencies:
-> (&priv->meth_lock){+.+...} ops: 0 {
   HARDIRQ-ON-W at:
                        [<ffffffff800614d0>] __lock_acquire+0x7fc/0x1a14
                        [<ffffffff800627e0>] lock_acquire+0xf8/0x150
                        [<ffffffff800128d0>] _spin_lock+0x30/0x44
                        [<ffffffff80263f20>] meth_reset+0x118/0x2d8
                        [<ffffffff8026424c>] meth_open+0x28/0x140
                        [<ffffffff802c1ae8>] dev_open+0xe0/0x18c
                        [<ffffffff802c1268>] dev_change_flags+0xd8/0x1d4
                        [<ffffffff804e7770>] ip_auto_config+0x1d4/0xf28
                        [<ffffffff80012e68>] do_one_initcall+0x58/0x170
                        [<ffffffff804cd190>] kernel_init+0x98/0x104
                        [<ffffffff8001520c>] kernel_thread_helper+0x10/0x18
   SOFTIRQ-ON-W at:
                        [<ffffffff800614f8>] __lock_acquire+0x824/0x1a14
                        [<ffffffff800627e0>] lock_acquire+0xf8/0x150
                        [<ffffffff800128d0>] _spin_lock+0x30/0x44
                        [<ffffffff80263f20>] meth_reset+0x118/0x2d8
                        [<ffffffff8026424c>] meth_open+0x28/0x140
                        [<ffffffff802c1ae8>] dev_open+0xe0/0x18c
                        [<ffffffff802c1268>] dev_change_flags+0xd8/0x1d4
                        [<ffffffff804e7770>] ip_auto_config+0x1d4/0xf28
                        [<ffffffff80012e68>] do_one_initcall+0x58/0x170
                        [<ffffffff804cd190>] kernel_init+0x98/0x104
                        [<ffffffff8001520c>] kernel_thread_helper+0x10/0x18
   INITIAL USE at:
                       [<ffffffff80061570>] __lock_acquire+0x89c/0x1a14
                       [<ffffffff800627e0>] lock_acquire+0xf8/0x150
                       [<ffffffff800128d0>] _spin_lock+0x30/0x44
                       [<ffffffff80263f20>] meth_reset+0x118/0x2d8
                       [<ffffffff8026424c>] meth_open+0x28/0x140
                       [<ffffffff802c1ae8>] dev_open+0xe0/0x18c
                       [<ffffffff802c1268>] dev_change_flags+0xd8/0x1d4
                       [<ffffffff804e7770>] ip_auto_config+0x1d4/0xf28
                       [<ffffffff80012e68>] do_one_initcall+0x58/0x170
                       [<ffffffff804cd190>] kernel_init+0x98/0x104
                       [<ffffffff8001520c>] kernel_thread_helper+0x10/0x18
 }
 ... key      at: [<ffffffff80cf6ce8>] __key.32424+0x0/0x8

stack backtrace:
Call Trace:
[<ffffffff8000ed0c>] dump_stack+0x8/0x34
[<ffffffff80060b74>] check_usage+0x470/0x4a0
[<ffffffff80060c34>] check_irq_usage+0x90/0x130
[<ffffffff80061f78>] __lock_acquire+0x12a4/0x1a14
[<ffffffff800627e0>] lock_acquire+0xf8/0x150
[<ffffffff80012a0c>] _spin_lock_irqsave+0x60/0x84
[<ffffffff8026388c>] meth_tx+0x48/0x43c
[<ffffffff802d3a38>] __qdisc_run+0x150/0x30c
[<ffffffff802c0aa8>] dev_queue_xmit+0x334/0x4b0
[<ffffffff804e7e6c>] ip_auto_config+0x8d0/0xf28
[<ffffffff80012e68>] do_one_initcall+0x58/0x170
[<ffffffff804cd190>] kernel_init+0x98/0x104
[<ffffffff8001520c>] kernel_thread_helper+0x10/0x18

..... timed out!
IP-Config: Retrying forever (NFS root)...
Sending DHCP requests ., OK
[...]

Fixed by converting all locks to irq locks.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Tested-by: NAndrew Randrianasulu <randrik_a@yahoo.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Napi structures are being created each time we open a port, but when
the port is closed the napi structure is only disabled but not removed.
This bug caused hang while removing the driver.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Sony TZ90 needs the cable type hardcoding. See bug #12734
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Reported-by: NJonathan E. Snow <jesnow@uh.edu>
[bart: port it from ata_piix to piix and give reporter the proper credit]
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

The second IDE channel of version 6 PCB is not being registered anymore since
the commit 48c3c107 (ide: add struct ide_host
(take 3)).
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Impact: fix an oops which always triggers

ide_tape_issue_pc() assumed drive->pc isn't NULL on invocation when
checking for back-to-back request sense issues but drive->pc can be
NULL and even when it's not NULL, it's not safe to dereference it once
the previous command is complete because pc could have been freed or
was on stack.  Kill back-to-back REQUEST_SENSE detection.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Processor idle power states C2 and C3 stop the TSC on many machines.
Linux recognizes this situation and marks the TSC as unstable:

Marking TSC unstable due to TSC halts in idle

But if those same machines are booted with "processor.max_cstate=1",
then there is no need to validate C2 and C3, and no need to
disable the TSC, which can be reliably used as a clocksource.
Signed-off-by: NLen Brown <len.brown@intel.com>
Acked-by: NThomas Gleixner <tglx@linutronix.de>

A previous 2.6.30 patch, a71e4917,
(ACPI: idle: mark_tsc_unstable() at init-time, not run-time)
erroneously disabled the TSC on systems that did not actually
have valid deep C-states.

Move the check after the deep-C-states are validated,
via new helper, tsc_check_state(), hich replaces tsc_halts_in_c().
Signed-off-by: NLen Brown <len.brown@intel.com>
Acked-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NFrans Pop <elendil@planet.nl>

If the BIOS hands us an invalid throttling state,
write a valid state.

http://bugzilla.kernel.org/show_bug.cgi?id=13259Signed-off-by: NZhang Rui <rui.zhang@intel.com>
Tested-by: NJames Ettle <theholyettlz@googlemail.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Introduce module parameter processor.ignore_tpc.

Some laptops are shipped with buggy _TPC,
this module parameter is used to to disable the buggy support.

http://bugzilla.kernel.org/show_bug.cgi?id=13259Signed-off-by: NZhang Rui <rui.zhang@intel.com>
Tested-by: NJames Ettle <theholyettlz@googlemail.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

drivers/built-in.o: In function `intel_opregion_init':
(.text+0x9d540): undefined reference to `acpi_video_register'

http://bugzilla.kernel.org/show_bug.cgi?id=13165Signed-off-by: NLen Brown <len.brown@intel.com>

In 2.6.29,
31878dd8
"ACPI: remove BM_RLD access from idle entry path"
moved BM_RLD initialization to init-time from run time.

But we discovered that some BIOS do not restore BM_RLD
after suspend, causing device errors on C3 and C4
after resume.  So now the kernel restores BM_RLD.

http://bugzilla.kernel.org/show_bug.cgi?id=13032Signed-off-by: NLen Brown <len.brown@intel.com>

The BIOS bug workaround mistakenly got disabled
when we followed the ACPI specification more closely
by ignoring OS updates to that bit.

(The BIOS is supposed to update SCI_EN, not the OS)

http://bugzilla.kernel.org/show_bug.cgi?id=13289Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

This patch provides new heuristics for parsing both the form factor and
media rotation rate ATA IDENFITY words.

The reported ATA version must be 7 or greater and the device must return
values defined as valid in the standard.  Only then are the
characteristics reported to SCSI via the VPD B1 page.

This seems like a reasonable compromise to me considering that we have
been shipping several kernel releases that key off the rotation rate bit
without any version checking whatsoever.  With no complaints so far.
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

For disks with 4KB sectors, report the correct block size and alignment
when filling out the READ CAPACITY(16) response.

This patch is based upon code from Matthew Wilcox' 4KB ATA tree.  I
fixed the bug I reported a while back caused by ATA and SCSI using
different approaches to describing the alignment.
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The bit 11 of command description is reserved bit in Freescale
SATA controller and needs to be set to '1'.  This is needed to
make sure the last write from the controller to the buffer
descriptor is seen before an interrupt is raised.
Signed-off-by: NDave Liu <daveliu@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

We we build with dma_addr_t as a 64-bit quantity we get:

drivers/ata/sata_fsl.c: In function 'sata_fsl_fill_sg':
drivers/ata/sata_fsl.c:340: warning: format '%x' expects type 'unsigned int', but argument 4 has type 'dma_addr_t'
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Issuing ATA_CMD_SET_FEATURES (0xef) times out because
pdc20621_interrupt ignores command completion since
ATA_TFLAG_POLLING flag is set.

This has already been fixed for sata_promise:

commit 51b94d2a
Author: Tejun Heo <htejun@gmail.com>
Date:   Fri Jun 8 13:46:55 2007 -0700

    sata_promise: use TF interface for polling NODATA commands

Also, this patch includes Mikael's original patches:

http://marc.info/?l=linux-ide&m=121135828227724&w=2
http://marc.info/?l=linux-ide&m=121144512109826&w=2Signed-off-by: NMikael Pettersson <mikpe@it.uu.se>
Signed-off-by: NDavid Milburn <dmilburn@redhat.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Commit 79e53945 introduced a
regression where you cannot use sysrq 'g' to enter kgdb.  The solution
is to move the intel fb sysrq over to V for video instead of G for
graphics.  The SMP VOYAGER code to register for the sysrq-v is not
anywhere to be found in the mainline kernel, so the comments in the
code were cleaned up as well.

This patch also cleans up the sysrq definitions for kgdb to make it
generic for the kernel debugger, such that the sysrq 'g' can be used
in the future to enter a gdbstub or another kernel debugger.
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>

The receive interrupt routine checks the wrong register if the
receive fifo is empty. Further an explicit interrupt acknowledge
write is introduced. In some circumstances another interrupt was
issued.
Signed-off-by: NBenjamin Krill <ben@codiert.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>