This patch updates the implementation of pci_process_bridge_OF_ranges to use
the of_pci_range_parser helpers.
Signed-off-by: NAndrew Murray <amurray@embedded-bits.co.uk>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This patch adds support to legacy serial for
UARTS with shifted registers.

The MVME5100 Single Board Computer is a PowerPC platform
that has 16550 style UARTS with register addresses that are
16 bytes apart (shifted by 4).

Commit 	30925748
"powerpc: Cleanup udbg_16550 and add support for LPC PIO-only UARTs"
added support to udbg_16550 for shifted registers by adding a "stride"
parameter to the initialisation operations for Programmed IO and
Memory Mapped IO.

As a consequence it is now possible to use the services of legacy serial
to provide early serial console messages for the MVME5100.

An added benefit of this is that the serial console will always be
"ttyS0" irrespective of whether the computer is fitted with extra
PCI 8250 interface boards or not.

I have tested this patch using the four PowerPC platforms available to me:

	MVME5100 - shifted registers,
	SAM440EP - unshifted registers,
	MPC8349 - unshifted registers,
	MVME4100 - unshifted registers.
Signed-off-by: NStephen Chivers <schivers@csc.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Function early_init_dt_scan_fw_dump() is called to scan the device
tree for fdump properties under node "rtas". Any one of them is
invalid, we can stop scanning the device tree early by returning
"1". It would save a bit time during boot.
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

When PCI_ERS_RESULT_CAN_RECOVER returned from device drivers, the
EEH core should enable I/O and DMA for the affected PE. However,
it was missed to have DMA enabled in eeh_handle_normal_event().
Besides, the frozen state of the affected PE should be cleared
after successful recovery, but we didn't.

The patch fixes both of the issues as above.
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The problem was initially reported by Wendy who tried pass through
IPR adapter, which was connected to PHB root port directly, to KVM
based guest. When doing that, pci_reset_bridge_secondary_bus() was
called by VFIO driver and linkDown was detected by the root port.
That caused all PEs to be frozen.

The patch fixes the issue by routing the reset for the secondary bus
of root port to underly firmware. For that, one more weak function
pci_reset_secondary_bus() is introduced so that the individual platforms
can override that and do specific reset for bridge's secondary bus.
Reported-by: NWendy Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Basically, we have 3 types of resets to fulfil PE reset: fundamental,
hot and PHB reset. For the later 2 cases, we need PCI bus reset hold
and settlement delay as specified by PCI spec. PowerNV and pSeries
platforms are running on top of different firmware and some of the
delays have been covered by underly firmware (PowerNV).

The patch makes the delays unified to be done in backend, instead of
EEH core.
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The issue was detected in a bit complicated test case where
we have multiple hierarchical PEs shown as following figure:

                +-----------------+
                | PE#3     p2p#0  |
                |          p2p#1  |
                +-----------------+
                        |
                +-----------------+
                | PE#4     pdev#0 |
                |          pdev#1 |
                +-----------------+

PE#4 (have 2 PCI devices) is the child of PE#3, which has 2 p2p
bridges. We accidentally had less-known scenario: PE#4 was removed
permanently from the system because of permanent failure (e.g.
exceeding the max allowd failure times in last hour), then we detects
EEH errors on PE#3 and tried to recover it. However, eeh_dev instances
for pdev#0/1 were not detached from PE#4, which was still connected to
PE#3. All of that was because of the fact that we rely on count-based
pcibios_release_device(), which isn't reliable enough. When doing
recovery for PE#3, we still apply hotplug on PE#4 and pdev#0/1, which
are not valid any more. Eventually, we run into kernel crash.

The patch fixes above issue from two aspects. For unplug, we simply
skip those permanently removed PE, whose state is (EEH_PE_STATE_ISOLATED
&& !EEH_PE_STATE_RECOVERING) and its frozen count should be greater
than EEH_MAX_ALLOWED_FREEZES. For plug, we marked all permanently
removed EEH devices with EEH_DEV_REMOVED and return 0xFF's on read
its PCI config so that PCI core will omit them.
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The patch introduces bootarg "eeh=off" to disable EEH functinality.
Also, it creates /sys/kerenl/debug/powerpc/eeh_enable to disable
or enable EEH functionality. By default, we have the functionality
enabled.

For PowerNV platform, we will restore to have the conventional
mechanism of clearing frozen PE during PCI config access if we're
going to disable EEH functionality. Conversely, we will rely on
EEH for error recovery.

The patch also fixes the issue that we missed to cover the case
of disabled EEH functionality in function ioda_eeh_event(). Those
events driven by interrupt should be cleared to avoid endless
reporting.
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

There're 2 EEH subsystem variables: eeh_subsystem_enabled and
eeh_probe_mode. We needn't maintain 2 variables and we can just
have one variable and introduce different flags. The patch also
introduces additional flag EEH_FORCE_DISABLE, which will be used
to disable EEH subsystem via boot parameter ("eeh=off") in future.
Besides, the patch also introduces flag EEH_ENABLED, which is
changed to disable or enable EEH functionality on the fly through
debugfs entry in future.

With the patch applied, the creteria to check the enabled EEH
functionality is changed to:

!EEH_FORCE_DISABLED && EEH_ENABLED : Enabled
                       Other cases : Disabled
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

When calling into eeh_gather_pci_data() on pSeries platform, we
possiblly don't have pci_dev instance yet, but eeh_dev is always
ready. So we use cached capability from eeh_dev instead of pci_dev
for log dump there. In order to keep things unified, we also cache
PCI capability positions to eeh_dev for PowerNV as well.
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The patch replaces printk(KERN_WARNING ...) with pr_warn() in the
function eeh_gather_pci_data().
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

We have suffered recrusive frozen PE a lot, which was caused
by IO accesses during the PE reset. Ben came up with the good
idea to keep frozen PE until recovery (BAR restore) gets done.
With that, IO accesses during PE reset are dropped by hardware
and wouldn't incur the recrusive frozen PE any more.

The patch implements the idea. We don't clear the frozen state
until PE reset is done completely. During the period, the EEH
core expects unfrozen state from backend to keep going. So we
have to reuse EEH_PE_RESET flag, which has been set during PE
reset, to return normal state from backend. The side effect is
we have to clear frozen state for towice (PE reset and clear it
explicitly), but that's harmless.

We have some limitations on pHyp. pHyp doesn't allow to enable
IO or DMA for unfrozen PE. So we don't enable them on unfrozen PE
in eeh_pci_enable(). We have to enable IO before grabbing logs on
pHyp. Otherwise, 0xFF's is always returned from PCI config space.
Also, we had wrong return value from eeh_pci_enable() for
EEH_OPT_THAW_DMA case. The patch fixes it too.
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

We've observed multiple PE reset failures because of PCI-CFG
access during that period. Potentially, some device drivers
can't support EEH very well and they can't put the device to
motionless state before PE reset. So those device drivers might
produce PCI-CFG accesses during PE reset. Also, we could have
PCI-CFG access from user space (e.g. "lspci"). Since access to
frozen PE should return 0xFF's, we can block PCI-CFG access
during the period of PE reset so that we won't get recrusive EEH
errors.

The patch adds flag EEH_PE_RESET, which is kept during PE reset.
The PowerNV/pSeries PCI-CFG accessors reuse the flag to block
PCI-CFG accordingly.
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

When doing PE reset, EEH_PE_ISOLATED is cleared unconditionally.
However, We should remove that if the PE reset has cleared the
frozen state successfully. Otherwise, the flag should be kept.
The patch fixes the issue.
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The PE state (for eeh_pe instance) EEH_PE_PHB_DEAD is duplicate to
EEH_PE_ISOLATED. Originally, those PHBs (PHB PE) with EEH_PE_PHB_DEAD
would be removed from the system. However, it's safe to replace
that with EEH_PE_ISOLATED.

The patch also clear EEH_PE_RECOVERING after fenced PHB has been handled,
either failure or success. It makes the PHB PE state consistent with:

	PHB functions normally		  NONE
	PHB has been removed		  EEH_PE_ISOLATED
	PHB fenced, recovery in progress  EEH_PE_ISOLATED | RECOVERING
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

module_init should return 0 or a negative errno.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Commit aac416fc (lkdtm: flush icache and report actions) calls
flush_icache_range from a module. It's exported on most architectures
that implement it, but not on powerpc. This patch exports it to fix
the module link failure.
Signed-off-by: NJeff Mahoney <jeffm@suse.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

3bc95598 ("powerpc/PCI: Use list_for_each_entry() for bus traversal")
caused a NULL pointer dereference because the loop body set the iterator to
NULL:

  Unable to handle kernel paging request for data at address 0x00000000
  Faulting instruction address: 0xc000000000041d78
  Oops: Kernel access of bad area, sig: 11 [#1]
  ...
  NIP [c000000000041d78] .sys_pciconfig_iobase+0x68/0x1f0
  LR [c000000000041e0c] .sys_pciconfig_iobase+0xfc/0x1f0
  Call Trace:
  [c0000003b4787db0] [c000000000041e0c] .sys_pciconfig_iobase+0xfc/0x1f0 (unreliable)
  [c0000003b4787e30] [c000000000009ed8] syscall_exit+0x0/0x98

Fix it by using a temporary variable for the iterator.

[bhelgaas: changelog, drop tmp_bus initialization]
Fixes: 3bc95598 powerpc/PCI: Use list_for_each_entry() for bus traversal
Signed-off-by: NMike Qiu <qiudayu@linux.vnet.ibm.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

Commit 8f619b54 ("powerpc/ppc64: Do not turn AIL (reloc-on
interrupts) too early") added code to set the AIL bit in the LPCR
without checking whether the kernel is running in hypervisor mode.  The
result is that when the kernel is running as a guest (i.e., under
PowerKVM or PowerVM), the processor takes a privileged instruction
interrupt at that point, causing a panic.  The visible result is that
the kernel hangs after printing "returning from prom_init".

This fixes it by checking for hypervisor mode being available before
setting LPCR.  If we are not in hypervisor mode, we enable relocation-on
interrupts later in pSeries_setup_arch using the H_SET_MODE hcall.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Recent CPUs support quad word load and store instructions. Add
support to the alignment handler for them.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

In:
  commit 742415d6
  Author: Michael Neuling <mikey@neuling.org>
  powerpc: Turn syscall handler into macros

We converted the syscall entry code onto macros, but in doing this we
introduced some cruft that's never run and should never have been added.

This removes that code.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Turn them on at the same time as we allow MSR_IR/DR in the paca
kernel MSR, ie, after the MMU has been setup enough to be able
to handle relocated access to the linear mapping.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

If we take an interrupt such as a trap caused by a BUG_ON before the
MMU has been setup, the interrupt handlers try to enable virutal mode
and cause a recursive crash, making the original problem very hard
to debug.

This fixes it by adjusting the "kernel_msr" value in the PACA so that
it only has MSR_IR and MSR_DR (translation for instruction and data)
set after the MMU has been initialized for the processor.

We may still not have a console yet but at least we don't get into
a recursive fault (and early debug console or memory dump via JTAG
of the kernel buffer *will* give us the proper error).
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

All our cpu feature updates were done for every CPU in the device-tree,
thus overwriting the cputable bits over and over again. Instead do them
only for the boot CPU.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Move the definition to setup-common.c and set the init value
to -1 on both 32 and 64-bit (it was 0 on 64-bit).

Additionally add a check to prom.c to garantee that the init
value has been udpated after the DT scan.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

For historical reasons that code was under #ifdef CONFIG_PPC_PSERIES
but it applies equally to all 64-bit platforms.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

We can't take an IRQ when we're about to do a trechkpt as our GPR state is set
to user GPR values.

We've hit this when running some IBM Java stress tests in the lab resulting in
the following dump:

  cpu 0x3f: Vector: 700 (Program Check) at [c000000007eb3d40]
      pc: c000000000050074: restore_gprs+0xc0/0x148
      lr: 00000000b52a8184
      sp: ac57d360
     msr: 8000000100201030
    current = 0xc00000002c500000
    paca    = 0xc000000007dbfc00     softe: 0     irq_happened: 0x00
      pid   = 34535, comm = Pooled Thread #
  R00 = 00000000b52a8184   R16 = 00000000b3e48fda
  R01 = 00000000ac57d360   R17 = 00000000ade79bd8
  R02 = 00000000ac586930   R18 = 000000000fac9bcc
  R03 = 00000000ade60000   R19 = 00000000ac57f930
  R04 = 00000000f6624918   R20 = 00000000ade79be8
  R05 = 00000000f663f238   R21 = 00000000ac218a54
  R06 = 0000000000000002   R22 = 000000000f956280
  R07 = 0000000000000008   R23 = 000000000000007e
  R08 = 000000000000000a   R24 = 000000000000000c
  R09 = 00000000b6e69160   R25 = 00000000b424cf00
  R10 = 0000000000000181   R26 = 00000000f66256d4
  R11 = 000000000f365ec0   R27 = 00000000b6fdcdd0
  R12 = 00000000f66400f0   R28 = 0000000000000001
  R13 = 00000000ada71900   R29 = 00000000ade5a300
  R14 = 00000000ac2185a8   R30 = 00000000f663f238
  R15 = 0000000000000004   R31 = 00000000f6624918
  pc  = c000000000050074 restore_gprs+0xc0/0x148
  cfar= c00000000004fe28 dont_restore_vec+0x1c/0x1a4
  lr  = 00000000b52a8184
  msr = 8000000100201030   cr  = 24804888
  ctr = 0000000000000000   xer = 0000000000000000   trap =  700

This moves tm_recheckpoint to a C function and moves the tm_restore_sprs into
that function.  It then adds IRQ disabling over the trechkpt critical section.
It also sets the TEXASR FS in the signals code to ensure this is never set now
that we explictly write the TM sprs in tm_recheckpoint.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
cc: stable@vger.kernel.org
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The current kernel code assumes big endian and parses RTAS events all
wrong. The most visible effect is that we cannot honor EPOW events,
meaning, for example, we cannot shut down a guest properly from the
hypervisor.

This new patch is largely inspired by Nathan's work: we get rid of all
the bit fields in the RTAS event structures (even the unused ones, for
consistency). We also introduce endian safe accessors for the fields used
by the kernel (trivial rtas_error_type() accessor added for consistency).

Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: NGreg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

While checking powersaving mode in machine check handler at 0x200, we
clobber CFAR register. Fix it by saving and restoring it during beq/bgt.
Signed-off-by: NMahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The ppc_rtas() syscall allows userspace to interact directly with RTAS.
For the moment, it assumes every thing is big endian and returns either
EINVAL or EFAULT when called in a little endian environment.

As suggested by Benjamin, to avoid bugs when userspace wants to pass
a non 32 bit value to RTAS, it is far better to stick with a simple
rationale: ppc_rtas() should be called with a big endian rtas_args
structure.

With this patch, it is now up to userspace to forge big endian arguments,
as expected by RTAS.
Signed-off-by: NGreg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The facility unavailable exception can be triggered from userspace by
accessing PMU registers when EBB is not enabled.  This causes the
included pr_err() to run, hence spamming the kernel log buffer.

This avoids this by rate limiting these messages.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Some power8 revisions have a hardware bug where we can lose a
Performance Monitor (PMU) exception under certain circumstances.

We will be adding a workaround for this case, see the next commit for
details. The observed behaviour is that writing PMAO doesn't cause an
exception as we would expect, hence the name of the feature.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Subsystems that want to register CPU hotplug callbacks, as well as perform
initialization for the CPUs that are already online, often do it as shown
below:

	get_online_cpus();

	for_each_online_cpu(cpu)
		init_cpu(cpu);

	register_cpu_notifier(&foobar_cpu_notifier);

	put_online_cpus();

This is wrong, since it is prone to ABBA deadlocks involving the
cpu_add_remove_lock and the cpu_hotplug.lock (when running concurrently
with CPU hotplug operations).

Instead, the correct and race-free way of performing the callback
registration is:

	cpu_notifier_register_begin();

	for_each_online_cpu(cpu)
		init_cpu(cpu);

	/* Note the use of the double underscored version of the API */
	__register_cpu_notifier(&foobar_cpu_notifier);

	cpu_notifier_register_done();

Fix the sysfs code in powerpc by using this latter form of callback
registration.

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Olof Johansson <olof@lixom.net>
Cc: Wang Dongsheng <dongsheng.wang@freescale.com>
Cc: Ingo Molnar <mingo@kernel.org>
Acked-by: NMadhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: NSrivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Add special state saving for critical and machine check exceptions.

Most of this code could be used to handle debug exceptions taken from
kernel space, but actually doing so is outside the scope of this patch.

The various critical and machine check exceptions now point to their
real handlers, rather than hanging the kernel.
Signed-off-by: NScott Wood <scottwood@freescale.com>

Use the proper scratch SPRG and PACA region.  Introduce level-specific
macros to simplify usage and avoid needing to do a bunch of token
pasting throughout EXCEPTION_COMMON().

Now that EXCEPTION_COMMON_DBG() is properly using the debug scratch
register, there's no more need for the caller to move the value to the
GEN scratch first.
Signed-off-by: NScott Wood <scottwood@freescale.com>

The ints parameter was used to optionally insert RECONCILE_IRQ_STATE
into EXCEPTION_COMMON.  However, since it came at the end of
EXCEPTION_COMMON, there was no real benefit for it to be there as
opposed to being called separately by the caller of EXCEPTION_COMMON.

The ints parameter was causing some hassle when trying to add an extra
macro layer.  Besides avoiding that, moving "ints" to the caller makes
the code simpler by:
 - avoiding the asymmetry where INTS_RESTORE_HARD is called separately
by the individual exception, but INTS_DISABLE was not
 - removing the no-op INTS_KEEP
 - not having an unnecessary macro parameter

It also turned out to be necessary to delay the INTS_DISABLE
in the case of special level exceptions until after we saved the
old value of PACAIRQHAPPENED.
Signed-off-by: NScott Wood <scottwood@freescale.com>

Previously SPRG3 was marked for use by both VDSO and critical
interrupts (though critical interrupts were not fully implemented).

In commit 8b64a9df ("powerpc/booke64:
Use SPRG0/3 scratch for bolted TLB miss & crit int"), Mihai Caraman
made an attempt to resolve this conflict by restoring the VDSO value
early in the critical interrupt, but this has some issues:

 - It's incompatible with EXCEPTION_COMMON which restores r13 from the
   by-then-overwritten scratch (this cost me some debugging time).
 - It forces critical exceptions to be a special case handled
   differently from even machine check and debug level exceptions.
 - It didn't occur to me that it was possible to make this work at all
   (by doing a final "ld r13, PACA_EXCRIT+EX_R13(r13)") until after
   I made (most of) this patch. :-)

It might be worth investigating using a load rather than SPRG on return
from all exceptions (except TLB misses where the scratch never leaves
the SPRG) -- it could save a few cycles.  Until then, let's stick with
SPRG for all exceptions.

Since we cannot use SPRG4-7 for scratch without corrupting the state of
a KVM guest, move VDSO to SPRG7 on book3e.  Since neither SPRG4-7 nor
critical interrupts exist on book3s, SPRG3 is still used for VDSO
there.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Cc: Mihai Caraman <mihai.caraman@freescale.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: kvm-ppc@vger.kernel.org

Once special level interrupts are supported, we may take nested TLB
misses -- so allow the same thread to acquire the lock recursively.

The lock will not be effective against the nested TLB miss handler
trying to write the same entry as the interrupted TLB miss handler, but
that's also a problem on non-threaded CPUs that lack TLB write
conditional.  This will be addressed in the patch that enables crit/mc
support by invalidating the TLB on return from level exceptions.
Signed-off-by: NScott Wood <scottwood@freescale.com>

altivec_unavailable was commented as 0xf20 but the code uses 0x200.
Note that 0xf20 is also used by ap_unavailable.

altivec_assist was commented as 0x1700 but the code uses 0x220.

critical_input was commented as 0x580 but the code uses 0x100.

machine_check was commented and implemented as 0x200, which conflicts
with altivec_assist (it only builds because MC_EXCEPTION_PROLOG is
commented out).  Changed to the fixed IVOR value of 0x000.
Signed-off-by: NScott Wood <scottwood@freescale.com>

We need to store thread info to these exception thread info like something
we already did for PPC32.
Signed-off-by: NTiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>