Add configuration callback for SPI bus 1 on GPD[8..10] and ensure the
correct GPIO configuration register definitions in regs-gpio.h
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Move the definition of the "generic" IRQ in the process.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add support for routing an IRQ from the normal ARM IRQ mechanism to the
FIQ input of the processor.

Note, also fix a bug where the init_FIQ() function has not been called
when CONFIG_FIQ is enabled.

Signed-off-by; Ben Dooks <ben@simtec.co.uk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add support for the Airgoo HMT (home media terminal) device.
The HMT is a tablet device with a s3c6410, a 7" LCD and a number
of peripheral connections.

For more details of the hardware specs, see:
http://article.gmane.org/gmane.linux.debian.devel.embedded/4307Signed-off-by: NPeter Korsgaard <jacmet@sunsite.dk>
[ben-linux@fluff.org: subject rewrite]
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add debugfs support for the cpufreq driver to allow
information about the system state to be exported to
the user.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add armclk for use with the cpufreq support and anything
else that may want it. This clock is just a direct
descendant of fclk.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add board support for CPUFREQ with the Simtec BAST board
registering the necessary information with the core.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add a sysdev S3C2410A sysdev to allow the differentiation
of the S3C2410A from the S3C2410. This is needed for the
CPUFREQ code to enable the extra features and update cpu
specific information.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add IO bank timing support for S3C2412/S3C2443.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Update the mapping of the memory controler registers and
add the missing definitions of the register block for the
SSMC.

The register contents definitions can be found in the pl093
header.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Currently map-base.h defines the main virtual address mappings made
for all the support S3C SoC series, but does not then define any base
for per-cpu mappings to be made from.

Add S3C_ADDR_CPU() macro to define an virtual address as an offset
from the last of the core mappings.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add core support for frequency scaling on the S3C2412 SoC.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add CPU frequency scalling support to the Simtec Osiris.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add entries to select the crystal to select for each different
supported board. This information is then available for anything
else requiring this, such as the CPUFreq PLL tables.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add PLL tables for the S3C2440.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add core support for frequency scaling on the S3C2440 SoC.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add PLL table for the S3C2410 SoC.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add core support for frequency scaling on the S3C2410 SoC.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add io-timing support for frequency scaling on the S3C2410 SoC.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add the S3C24XX to the main ARM CPUFreq Kconfig support list.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add ARCH_HAS_CPUFREQ so that each machine config can select
it if they have CPUFREQ driver support. This means that the
CPUFREQ specific area does not need the if statement updating
each time a new machine is added.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Move the structure s3c_cpufreq_config from cpu-freq.h to the
less advertised cpu-freq-core.h as it is not needed by anything
outside the core drivers.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Update arch/arm/plat-s3c/include/plat/cpu-freq.h to include kerneldoc
style documentation.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add the core of the support for enabling the CPUFreq driver on
all S3C24XX based systems.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add definitions and an accessor macro to deal with
reading bus information from S3C2410_BWSCON for any
given numbered bank.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

The value of armclk_mask needs to be inverted for use as a mask on
the register value when updating ARM_RATIO.

This is critical for cpufreq support, without it attempts to scale
the frequency of the core trash pretty much the entire clock tree.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

If the requested clock is faster than the parent clock then the
parent clock is the closest we can get to the request so we need
to return that instead of the requested clock.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

In the s3c_gpiolib_getchip implementation for s3c24xx the check whether a pin is
in the gpio banks range is reversed. Thus the function returns NULL for valid
pins and the gpio chip if its not valid.

As a result gpio states are not saved/restored properly during suspend/resume.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

mm: Pass virtual address to [__]p{te,ud,md}_free_tlb()

Upcoming paches to support the new 64-bit "BookE" powerpc architecture
will need to have the virtual address corresponding to PTE page when
freeing it, due to the way the HW table walker works.

Basically, the TLB can be loaded with "large" pages that cover the whole
virtual space (well, sort-of, half of it actually) represented by a PTE
page, and which contain an "indirect" bit indicating that this TLB entry
RPN points to an array of PTEs from which the TLB can then create direct
entries. Thus, in order to invalidate those when PTE pages are deleted,
we need the virtual address to pass to tlbilx or tlbivax instructions.

The old trick of sticking it somewhere in the PTE page struct page sucks
too much, the address is almost readily available in all call sites and
almost everybody implemets these as macros, so we may as well add the
argument everywhere. I added it to the pmd and pud variants for consistency.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: David Howells <dhowells@redhat.com> [MN10300 & FRV]
Acked-by: NNick Piggin <npiggin@suse.de>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> [s390]
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix i2c_board_info definitions - we were defining the 'type' field
of these structures twice since the first argument of I2C_BOARD_INFO
sets this field.  Move the second definition into I2C_BOARD_INFO().
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NBen Dooks <ben-linux@fluff.org>

Add support for the ADC controller on the S3C series of processors to
drivers/hwmon for use with hardware monitoring systems.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

To add HWMON support, we need a synchronous read() call that blocks
until completion. Add the client that is being service to the select
and convert callbacks to make the code easier.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add platform device information for the ADC channels to be exported
via HWMON. This exports all the ADCs not being used for the touchscreen
interface.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Change the hwmon device name to something more generic as this
should be functional for both the s3c24xx and s3c64xx archs.

Since it has yet to have a driver, it is pretty safe to change
as there are no extant users.

Also add the necessary entry in devs.h which seems to have been
missed  out at somepoint.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Removed the LBD support that isn't of any use right now at least,
then remove remnants of the TCM config flags that somehow crept
in by mistake (not yet merged patch for 2.6.32) and then the usual
defconfig noise from updated menus.
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Pull the initial preempt_count value into a single
definition site.

Maintainers for: alpha, ia64 and m68k, please have a look,
your arch code is funny.

The header magic is a bit odd, but similar to the KERNEL_DS
one, CPP waits with expanding these macros until the
INIT_THREAD_INFO macro itself is expanded, which is in
arch/*/kernel/init_task.c where we've already included
sched.h so we're good.

Cc: tony.luck@intel.com
Cc: rth@twiddle.net
Cc: geert@linux-m68k.org
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: NMatt Mackall <mpm@selenic.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This makes the VIC resume from suspend flagged IRQ:s identical to
the flags indicating all possible interrupts. This is perhaps not
the optimal setting but setting it to 0 makes the system suspend
and never come back again (all IRQ sources masked off).
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

<linux/io.h> was getting included by <mach/ts72xx.h>, is should be
included by this file.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Correct define typo (. -> ,)
Signed-off-by: NSimon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: NNicolas Pitre <nico@marvell.com>

Attepmpt to configure ULPI pins gives the following compile error:
  CC      arch/arm/mach-pxa/cm-x300.o
  arch/arm/mach-pxa/cm-x300.c:155: error: 'MFP_MFP_AF0' undeclared here (not in a function)
  arch/arm/mach-pxa/cm-x300.c:155: error: 'MFP_MFP_DS01X' undeclared here (not in a function)
  make[2]: *** [arch/arm/mach-pxa/cm-x300.o] Error 1
  make[1]: *** [arch/arm/mach-pxa] Error 2
  make: *** [sub-make] Error 2

Fix it.
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>