Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The operation conditions register (OCR) stores the voltage
profile of the card, however the list of possible voltages
is restricted by the voltage range supported by the supply
used as VCC/VDD. So in mmc_vddrange_to_ocrmask() a OCR mask
is obtained to filter the not supported voltages, from the
value read in the host controller OCR register.

For fixed regulators, regulator_list_voltage() returns the
fixed output for the first selector but this doesn't happen
for switch (FET) regulators that obtain their voltage from
their parent supply. A call to regulator_get_voltage() is
needed in this case so the regulator core can return the
FET's parent supply voltage output.

This change is consistent with the fact that for other
fixed regulators (that are not FETs) the OCR mask is
returned even when mmc_regulator_set_ocr() checks if the
regulator is fixed before calling regulator_set_voltage().

Without this patch, the following warning is reported when
a FET is used as a vmmc-supply:

dwmmc_exynos 12220000.mmc: Failed getting OCR mask: -22
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Some eMMC and SD cards implement a DSR register that allows to tune
raise/fall times and drive strength of the CMD and DATA outputs.
The values to use depend on the card in use and the host.
It might be needed to reduce the drive strength to prevent voltage peaks
above the host's specification.

Implement a 'dsr' devicetree property that allows to specify the value
to set the DSR to. For non-dt setups the new members of mmc_host can be
set by board code.

This patch was initially authored by Sascha Hauer. It contains
improvements authored by Markus Niebel and Uwe Kleine-König.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NMarkus Niebel <Markus.Niebel@tq-group.com>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

.set_uhs_signaling field is currently initialised twice once to the
arch specific callback pxav3_set_uhs_signaling, and also to the generic
sdhci_set_uhs_signaling callback.

This means that uhs is currently broken for this platform currently, as pxav3
has some special constriants which means it can't use the generic callback.

This happened in
commit 96d7b78c ("mmc: sdhci: convert sdhci_set_uhs_signaling() into a library function")
commit a702c8ab ("mmc: host: split up sdhci-pxa, create sdhci-pxav3.c")'

Fix this and hopefully prevent it happening in the future by ensuring named
initialisers always follow the declaration order in the structure definition.
Signed-off-by: NPeter Griffin <peter.griffin@linaro.org>
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This allows us to get rid of the #else condition, as the macro compiles
away to nothing if not enabled.
Signed-off-by: NPeter Griffin <peter.griffin@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This allows us to get rid of the #else condition, as the macro compiles
away to nothing if not enabled.
Signed-off-by: NPeter Griffin <peter.griffin@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

As the code is using SIMPLE_DEV_PM_OPS helper, this compiles away to
nothing if CONFIG_PM_SLEEP is disabled. Thus we don't need to #define
the suspend/resume callbacks to NULL.
Signed-off-by: NPeter Griffin <peter.griffin@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

As the code is using SIMPLE_DEV_PM_OPS helper, this compiles away to
nothing if CONFIG_PM_SLEEP is disabled. Thus we don't need to #define
the suspend/resume callbacks to NULL.
Signed-off-by: NPeter Griffin <peter.griffin@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway.
Signed-off-by: NPeter Griffin <peter.griffin@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

781e989c ("mmc: sdhci: convert to new SDIO IRQ handling") and
bf3b5ec6 ("mmc: sdio_irq: rework sdio irq handling") disabled
the use of our own custom threaded IRQ handler, but left in an
unconditional wake_up_process() on that handler at resume-time.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=80151

In addition, the check for MMC_CAP_SDIO_IRQ capability is added
before enable sdio IRQ.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NChris Ball <chris@printf.net>
Signed-off-by: NFu Zhonghui <zhonghui.fu@linux.intel.com>
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

There are upcoming MIPS SoCs with dw_mmc hosts.
Signed-off-by: NAndrew Bresticker <abrestic@chromium.org>
Reviewed-by: NAlim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The dw_mmc drivers rely on the DMA API, so update the Kconfig entry
to depend on HAS_DMA.  Since the drivers should build on any platform
with DMA, allow the driver to compile tested on non-ARC/ARM platforms.
Signed-off-by: NAndrew Bresticker <abrestic@chromium.org>
Reviewed-by: NAlim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

when SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK is set, timeout_clk is sdclk.
We need to update it when we change sdclk in sdhci_set_clock.
This allow to have a more precisse timeout and max_busy_timeout. This
can help for command that need a big busy wait (erase, ...).
Signed-off-by: NMatthieu CASTET <matthieu.castet@parrot.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

When we wait for busy after sending a command, if there is
a timeout, we got SDHCI_INT_DATA_TIMEOUT flags.
Before this commit we got the message :
"Got data interrupt 0x00100000 even though no data  operation was in progress."
and we need to wait 10s that sdhci_timeout_timer expires.
Signed-off-by: NMatthieu CASTET <matthieu.castet@parrot.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Current code erroneously fill the last byte of R2 response with an undefined
value. In addition, the controller actually 'offloads' the last byte
(CRC7, end bit) while receiving R2 response and thus it's impossible to get the
actual value. This could cause mmc stack to obtain inconsistent CID from the
same card after resume and misidentify it as a different card.

Fix by assigning dummy CRC and end bit: {7'b0, 1} = 0x1 to the last byte of R2.

Cc: <stable@vger.kernel.org> # v3.16+
Fixes: c7f6558d ("mmc: Add realtek USB sdmmc host driver")
Signed-off-by: NRoger Tseng <rogerable@realtek.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Current code erroneously fill the last byte of R2 response with an undefined
value. In addition, the controller actually 'offloads' the last byte
(CRC7, end bit) while receiving R2 response and thus it's impossible to get the
actual value. This could cause mmc stack to obtain inconsistent CID from the
same card after resume and misidentify it as a different card.

Fix by assigning dummy CRC and end bit: {7'b0, 1} = 0x1 to the last byte of R2.

Cc: <stable@vger.kernel.org> # v3.8+
Fixes: ff984e57 ("mmc: Add realtek pcie sdmmc host driver")
Signed-off-by: NRoger Tseng <rogerable@realtek.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

If we happened to get a data error at just the wrong time the dw_mmc
driver could get into a state where it would never complete its
request.  That would leave the caller just hanging there.

We fix this two ways and both of the two fixes on their own appear to
fix the problems we've seen:

1. Fix a race in the tasklet where the interrupt setting the data
   error happens _just after_ we check for it, then we get a
   EVENT_XFER_COMPLETE.  We fix this by repeating a bit of code.
2. Fix it so that if we detect that we've got an error in the "data
   busy" state and we're not going to do anything else we end the
   request and unblock anyone waiting.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NYuvaraj Kumar C D <yuvaraj.cd@gmail.com>
Acked-by: NSeungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

eMMC card can support up to 7 physical partitions, including 2 boot,
1 RPMB and 4 GPs. Change MMC_NUM_PHY_PARTITION from 6 to 7, which is
the correct value.
Signed-off-by: NYi Sun <yi.y.sun@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

curr should use signed type since it will contain the returned
value which is possible to be a negative value. Using u32 will
make the returned value to be true even there is a negative result.
Change to use int instead of u32
Signed-off-by: NChuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Make use of the MMC asynchronous request capability to prepare the
next DMA transfer request in parallel with the current transfer.
This is done by adding pre-request and post-request callbacks that are
used by the MMC framework during an active data transfer.

It should help reduce the impact of DMA preparation overhead on the SD
card performance.
Signed-off-by: NApelete Seketeli <apelete@seketeli.net>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Until now the MMC driver for JZ4740 SoC was relying on PIO mode only
for data transfers.
This patch allows the use of DMA for data trasnfers in addition to PIO
mode by relying on DMA Engine.

DMA tranfers performance might be further improved by taking advantage
of the asynchronous request capability of the MMC framework.
Signed-off-by: NApelete Seketeli <apelete@seketeli.net>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch focuses on clock setting for RK3288 mmc controller.

In RK3288 mmc controller, CLKDIV register can only be set 0 or 1,
and if DDR 8bit mode, CLKDIV register must be set 1.
Signed-off-by: NAddy Ke <addy.ke@rock-chips.com>
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch adds an include of linux/types.h to make sure bool is defined
before utilized in this header file.
Signed-off-by: NHans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The code selecting a device for the sdhci host has been
continuously tweaked (4b711cb1
"mmc: sdhci-pltfm: Add structure for host-specific data" and
a4d2177f "mmc: sdhci-pltfm: dt
device does not pass parent to sdhci_alloc_host" while there
does not seem to be any reason to use platform device's parent
in the first place.

The comment saying "Some PCI-based MFD need the parent here"
seem to refer to Timberdale FPGA driver (the only MFD driver
registering SDHCI cell, drivers/mfd/timberdale.c) but again,
the only situation when parent device matter is runtime PM,
which is not implemented for Timberdale.
Signed-off-by: NPawel Moll <pawel.moll@arm.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

There is no need for regulator consumers to include special logic for
fixed voltage regulators as they support regulator_set_voltage() just
like their non-fixed regulator counterparts.
Signed-off-by: NTim Kryger <tim.kryger@gmail.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

On Qualcomm APQ8064 SOCs, SD card controller has an additional glue
called DML (Data Mover Local/Lite) to assist dma transfers.
This hardware needs to be setup before any dma transfer is requested.
DML itself is not a DMA engine, its just a gule between the SD card
controller and dma controller.

Most of this code has been ported from qualcomm's 3.4 kernel.

This patch adds the code necessary to intialize the hardware and setup
before doing any dma transfers.
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Runtime Power Management handling for the sdhci_add_host() failure
case in sdhci_s3c_probe() should match the code in sdhci_s3c_remove()
(which uses pm_runtime_disable() call which matches the earlier
pm_runtime_enable() one).  Fix it.

This patch fixes "BUG: spinlock bad magic on CPU#0, swapper/0/1" and
"Unbalanced pm_runtime_enable!" warnings.

>From the kernel log:
...
[    1.659631] s3c-sdhci 12530000.sdhci: sdhci_add_host() failed
[    1.665096] BUG: spinlock bad magic on CPU#0, swapper/0/1
[    1.670433]  lock: 0xea01e484, .magic: 00000000, .owner: <none>/-1, .owner_cpu: 0
[    1.677895] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.16.0-next-20140804-00008-ga59480f-dirty #707
[    1.687037] [<c0013ae4>] (unwind_backtrace) from [<c0010d70>] (show_stack+0x10/0x14)
[    1.694740] [<c0010d70>] (show_stack) from [<c04050c8>] (dump_stack+0x68/0xb8)
[    1.701948] [<c04050c8>] (dump_stack) from [<c0052558>] (do_raw_spin_lock+0x15c/0x1a4)
[    1.709848] [<c0052558>] (do_raw_spin_lock) from [<c040a630>] (_raw_spin_lock_irqsave+0x20/0x28)
[    1.718619] [<c040a630>] (_raw_spin_lock_irqsave) from [<c030d7d0>] (sdhci_do_set_ios+0x1c/0x5cc)
[    1.727464] [<c030d7d0>] (sdhci_do_set_ios) from [<c030ddfc>] (sdhci_runtime_resume_host+0x50/0x104)
[    1.736574] [<c030ddfc>] (sdhci_runtime_resume_host) from [<c02462dc>] (pm_generic_runtime_resume+0x2c/0x40)
[    1.746383] [<c02462dc>] (pm_generic_runtime_resume) from [<c0247898>] (__rpm_callback+0x34/0x70)
[    1.755233] [<c0247898>] (__rpm_callback) from [<c02478fc>] (rpm_callback+0x28/0x88)
[    1.762958] [<c02478fc>] (rpm_callback) from [<c02486f0>] (rpm_resume+0x384/0x4ec)
[    1.770511] [<c02486f0>] (rpm_resume) from [<c02488b0>] (pm_runtime_forbid+0x58/0x64)
[    1.778325] [<c02488b0>] (pm_runtime_forbid) from [<c030ea70>] (sdhci_s3c_probe+0x4a4/0x540)
[    1.786749] [<c030ea70>] (sdhci_s3c_probe) from [<c02429cc>] (platform_drv_probe+0x2c/0x5c)
[    1.795076] [<c02429cc>] (platform_drv_probe) from [<c02415f0>] (driver_probe_device+0x114/0x234)
[    1.803929] [<c02415f0>] (driver_probe_device) from [<c024179c>] (__driver_attach+0x8c/0x90)
[    1.812347] [<c024179c>] (__driver_attach) from [<c023ffb4>] (bus_for_each_dev+0x54/0x88)
[    1.820506] [<c023ffb4>] (bus_for_each_dev) from [<c0240df8>] (bus_add_driver+0xd8/0x1cc)
[    1.828665] [<c0240df8>] (bus_add_driver) from [<c0241db8>] (driver_register+0x78/0xf4)
[    1.836652] [<c0241db8>] (driver_register) from [<c00088a4>] (do_one_initcall+0x80/0x1d0)
[    1.844816] [<c00088a4>] (do_one_initcall) from [<c059ac94>] (kernel_init_freeable+0x108/0x1d4)
[    1.853503] [<c059ac94>] (kernel_init_freeable) from [<c0401300>] (kernel_init+0x8/0xe4)
[    1.861568] [<c0401300>] (kernel_init) from [<c000e538>] (ret_from_fork+0x14/0x3c)
[    1.869582] platform 12530000.sdhci: Driver s3c-sdhci requests probe deferral
...
[    1.997047] s3c-sdhci 12530000.sdhci: Unbalanced pm_runtime_enable!
...
[    2.027235] s3c-sdhci 12530000.sdhci: sdhci_add_host() failed
[    2.032884] platform 12530000.sdhci: Driver s3c-sdhci requests probe deferral
...

Tested on Hardkernel's Exynos4412 based ODROID-U3 board.

Fixes: 9f4e8151 ("mmc: sdhci-s3c: Enable runtime power management")
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

new link for - How to piss off a Linux kernel subsystem maintainer
Signed-off-by: NSudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The NFS/RDMA Kconfig symbol was split into separate options for client
and server in commit 2e8c12e1 ("xprtrdma: add separate Kconfig
options for NFSoRDMA client and server support").

Update the documentation to reflect this split.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Reviewed-by: NJeff Layton <jlayton@redhat.com>
Signed-off-by: NRandy Dunlap <rdunlap@infradead.org>
Cc: "J. Bruce Fields" <bfields@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

hpfall.c was renamed to freefall.c in 3.16, but this file still refer to
hpfall.c instead of freefall.c
Signed-off-by: NMasanari Iida <standby24x7@gmail.com>
Signed-off-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The example code provided with the i2c device interface documentation
won't compile since it uses the reserved word "register" to name a
variable.

The compiler fails with this error message:

 error: expected identifier or '(' before '=' token
   __u8 register = 0x20; /* Device register to access */
                 ^

Rename the variable "register" to simply "reg" in the example code.

Another couple of typos has been fixed as well.
[Change "! =" to "!=".]
Signed-off-by: NJose Alarcon Roldan <jose.alarcon.roldan@gmail.com>
Signed-off-by: NRandy Dunlap <rdunlap@infradead.org>
Acked-by: NWolfram Sang <wsa@the-dreams.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Despite the fact that these functions have been around for years, they
are little used (only 15 uses in 13 files at the preseht time) even
though many other files use work-arounds to achieve the same result.

By documenting them, hopefully they will become more widely used.
Signed-off-by: NRob Jones <rob.jones@codethink.co.uk>
Acked-by: NSteven Whitehouse <swhiteho@redhat.com>
Signed-off-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull ACPI and power management fixes from Rafael Wysocki:
 "These are regression fixes (ACPI sysfs, ACPI video, suspend test),
  ACPI cpuidle deadlock fix, missing runtime validation of ACPI _DSD
  output, a fix and a new CPU ID for the RAPL driver, new blacklist
  entry for the ACPI EC driver and a couple of trivial cleanups
  (intel_pstate and generic PM domains).

  Specifics:

   - Fix for recently broken test_suspend= command line argument (Rafael
     Wysocki).

   - Fixes for regressions related to the ACPI video driver caused by
     switching the default to native backlight handling in 3.16 from
     Hans de Goede.

   - Fix for a sysfs attribute of ACPI device objects that returns stale
     values sometimes due to the fact that they are cached instead of
     executing the appropriate method (_SUN) every time (broken in
     3.14).  From Yasuaki Ishimatsu.

   - Fix for a deadlock between cpuidle_lock and cpu_hotplug.lock in the
     ACPI processor driver from Jiri Kosina.

   - Runtime output validation for the ACPI _DSD device configuration
     object missing from the support for it that has been introduced
     recently.  From Mika Westerberg.

   - Fix for an unuseful and misleading RAPL (Running Average Power
     Limit) domain detection message in the RAPL driver from Jacob Pan.

   - New Intel Haswell CPU ID for the RAPL driver from Jason Baron.

   - New Clevo W350etq blacklist entry for the ACPI EC driver from Lan
     Tianyu.

   - Cleanup for the intel_pstate driver and the core generic PM domains
     code from Gabriele Mazzotta and Geert Uytterhoeven"

* tag 'pm+acpi-3.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI / cpuidle: fix deadlock between cpuidle_lock and cpu_hotplug.lock
  ACPI / scan: not cache _SUN value in struct acpi_device_pnp
  cpufreq: intel_pstate: Remove unneeded variable
  powercap / RAPL: change domain detection message
  powercap / RAPL: add support for CPU model 0x3f
  PM / domains: Make generic_pm_domain.name const
  PM / sleep: Fix test_suspend= command line option
  ACPI / EC: Add msi quirk for Clevo W350etq
  ACPI / video: Disable native_backlight on HP ENVY 15 Notebook PC
  ACPI / video: Add a disable_native_backlight quirk
  ACPI / video: Fix use_native_backlight selection logic
  ACPICA: ACPI 5.1: Add support for runtime validation of _DSD package.

Pull filesystem fixes from Al Viro:
 "Several bugfixes (all of them -stable fodder).

  Alexey's one deals with double mutex_lock() in UFS (apparently, nobody
  has tried to test "ufs: sb mutex merge + mutex_destroy" on something
  like file creation/removal on ufs).  Mine deal with two kinds of
  umount bugs, in umount propagation and in handling of automounted
  submounts, both resulting in bogus transient EBUSY from umount"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  ufs: fix deadlocks introduced by sb mutex merge
  fix EBUSY on umount() from MNT_SHRINKABLE
  get rid of propagate_umount() mistakenly treating slaves as busy.

Pull RCU fix from Ingo Molnar:
 "A boot hang fix for the offloaded callback RCU model (RCU_NOCB_CPU=y
  && (TREE_CPU=y || TREE_PREEMPT_RC)) in certain bootup scenarios"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  rcu: Make nocb leader kthreads process pending callbacks after spawning

Pull timer fixes from Thomas Gleixner:
 "Three fixlets from the timer departement:

   - Update the timekeeper before updating vsyscall and pvclock.  This
     fixes the kvm-clock regression reported by Chris and Paolo.

   - Use the proper irq work interface from NMI.  This fixes the
     regression reported by Catalin and Dave.

   - Clarify the compat_nanosleep error handling mechanism to avoid
     future confusion"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  timekeeping: Update timekeeper before updating vsyscall and pvclock
  compat: nanosleep: Clarify error handling
  nohz: Restore NMI safe local irq work for local nohz kick

Commit 0244756e ("ufs: sb mutex merge + mutex_destroy") introduces
deadlocks in ufs_new_inode() and ufs_free_inode().
Most callers of that functions acqure the mutex by themselves and
ufs_{new,free}_inode() do that via lock_ufs(),
i.e we have an unavoidable double lock.

The patch proposes to resolve the issue by making sure that
ufs_{new,free}_inode() are not called with the mutex held.

Found by Linux Driver Verification project (linuxtesting.org).

Cc: stable@vger.kernel.org # 3.16
Signed-off-by: NAlexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Pull kvm fixes from Paolo Bonzini:
 "A smattering of bug fixes across most architectures"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  powerpc/kvm/cma: Fix panic introduces by signed shift operation
  KVM: s390/mm: Fix guest storage key corruption in ptep_set_access_flags
  KVM: s390/mm: Fix storage key corruption during swapping
  arm/arm64: KVM: Complete WFI/WFE instructions
  ARM/ARM64: KVM: Nuke Hyp-mode tlbs before enabling MMU
  KVM: s390/mm: try a cow on read only pages for key ops
  KVM: s390: Fix user triggerable bug in dead code