The Intel Bluetooth controllers can emit extra vendor specific events in
error conditions or for debugging purposes. To make the life easier for
engineers, enable them by default. When the vendor_diag options has been
enabled, then additional debug events are also enabled.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

For Intel bootloader devices, set the manufacturer information so that
it becomes possible to decode the boot process.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Provide an early indication about the manufacturer information so that
it can be forwarded into monitor channel.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The latest Apple Bluetooth controllers with Broadcom chip in it have
a small design change. Instead of including a USB hub with mouse and
keyboard devices, they are now HID interfaces on the same device.

T:  Bus=04 Lev=02 Prnt=02 Port=04 Cnt=01 Dev#= 39 Spd=12   MxCh= 0
D:  Ver= 2.01 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=05ac ProdID=8290 Rev= 0.79
S:  Manufacturer=Broadcom Corp.
S:  Product=Bluetooth USB Host Controller
C:* #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr=  0mA
A:  FirstIf#= 2 IfCount= 4 Cls=ff(vend.) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 1 Cls=03(HID  ) Sub=01 Prot=01 Driver=usbhid
E:  Ad=85(I) Atr=03(Int.) MxPS=   8 Ivl=10ms
I:* If#= 1 Alt= 0 #EPs= 1 Cls=03(HID  ) Sub=01 Prot=02 Driver=usbhid
E:  Ad=86(I) Atr=03(Int.) MxPS=   8 Ivl=10ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 3 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 3 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 3 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 3 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 3 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=btusb
E:  Ad=84(I) Atr=02(Bulk) MxPS=  32 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=  32 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)

The general layout of Bluetooth devices is that interface 0 is the main
interface and interface 1 is for audio data. This design obviously moves
it to main interface 2 and audio data on interface 3.

Starting with the MacBookPro12,1 (early 2015 models) the new Broadcom
BCM943602CS cards are used which show this interface layout.

usb 4-1.5: New USB device found, idVendor=05ac, idProduct=8290
usb 4-1.5: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 4-1.5: Product: Bluetooth USB Host Controller
usb 4-1.5: Manufacturer: Broadcom Corp.
Bluetooth: hci0: BCM: chip id 102 build 0243
Bluetooth: hci0: BCM: product 05ac:8290
Bluetooth: hci0: BCM20703A1 Generic USB UHE Apple 20Mhz fcbga_X87
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

For the controllers from Intel and Broadcom (including Apple), it is
helpful to have the information about the manufacturer send out early.

This patch sets the hdev->manufacturer information which will be send
out before actually calling the vendor specific hdev->setup driver
callback.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

T: Bus=04 Lev=02 Prnt=02 Port=04 Cnt=01 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0cf3 ProdID=817b Rev=00.02
C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

BugLink: https://bugs.launchpad.net/bugs/1506615Signed-off-by: NDmitry Tunin <hanipouspilot@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org

This adapter works with the existing linux-firmware.

T:  Bus=01 Lev=01 Prnt=01 Port=03 Cnt=02 Dev#=  3 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0930 ProdID=021c Rev=00.01
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

BugLink: https://bugs.launchpad.net/bugs/1502781Signed-off-by: NDmitry Tunin <hanipouspilot@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org

Recently salvaged this 'BCM43142A0' WiFi/Bluetooth module from a Lenovo laptop
and noticed it doesn't work automatically, because the USB IDs are missing
from btusb.c.

Plugging in the adapter on Linux 4.1 (dmesg):
usb 3-3.3.3: new full-speed USB device number 90 using xhci_hcd
usb 3-3.3.3: New USB device found, idVendor=105b, idProduct=e065
usb 3-3.3.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 3-3.3.3: Product: BCM43142A0
usb 3-3.3.3: Manufacturer: Broadcom Corp
usb 3-3.3.3: SerialNumber: 0090A286559E

/sys/kernel/debug/usb/devices:
T:  Bus=03 Lev=03 Prnt=22 Port=02 Cnt=02 Dev#= 90 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=105b ProdID=e065 Rev= 1.12
S:  Manufacturer=Broadcom Corp
S:  Product=BCM43142A0
S:  SerialNumber=0090A286559E
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=84(I) Atr=02(Bulk) MxPS=  32 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=  32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)

Support for the chipset was added in commit 88f9b65d and a similar BCM43142
based device was added in commit 8f0c304c.

To work around the issue, I got the firmware
(BCM43142A0_001.001.011.0122.0153) off a Windows installation of Broadcom
bluetooth driver and converted it to a .hcd -file via. hex2hcd and placed it
in /lib/firmware/brcm/BCM.hcd. After that:

$ echo "105b e065 0 19ff 0239" > /sys/bus/usb/drivers/btusb/new_id
...(plug in the adapter)
usb 3-3.3.3: new full-speed USB device number 91 using xhci_hcd
usb 3-3.3.3: New USB device found, idVendor=105b, idProduct=e065
usb 3-3.3.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 3-3.3.3: Product: BCM43142A0
usb 3-3.3.3: Manufacturer: Broadcom Corp
usb 3-3.3.3: SerialNumber: 0090A286559E
Bluetooth: hci0: BCM: chip id 70
Bluetooth: hci0: BCM (001.001.011) build 0000
bluetooth hci0: firmware: direct-loading firmware brcm/BCM.hcd
Bluetooth: hci0: BCM (001.001.011) build 0154

Bam, now it works for me!

/sys/kernel/debug/usb/devices:
T:  Bus=03 Lev=03 Prnt=22 Port=02 Cnt=02 Dev#= 92 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=105b ProdID=e065 Rev= 1.12
S:  Manufacturer=Broadcom Corp
S:  Product=BCM43142A0
S:  SerialNumber=0090A286559E
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=84(I) Atr=02(Bulk) MxPS=  32 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=  32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Signed-off-by: NSanttu Rekilä <sare@r00t3d.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

For the Apple Bluetooth devices, read the USB product information and
print them. This allows for easy mapping of chip and USB details.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The calculation for the firmware version number is off by one bit.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The BCM2045 seems to have a problem with the stored link key commands
and thus just mark them as broken.

  HCI Event: Command Complete (0x0e) plen 12
     Read Local Supported Features (0x04|0x0003) ncmd 1
     status 0x00
     Features: 0xff 0xff 0x8d 0xfe 0x8f 0xf9 0x00 0x80
  HCI Event: Command Complete (0x0e) plen 12
     Read Local Version Information (0x04|0x0001) ncmd 1
     status 0x00
     HCI Version: 2.0 (0x3) HCI Revision: 0x2000
     LMP Version: 2.0 (0x3) LMP Subversion: 0x410d
     Manufacturer: Broadcom Corporation (15)
  HCI Event: Command Complete (0x0e) plen 11
     Read Buffer Size (0x04|0x0005) ncmd 1
     status 0x00
     ACL MTU 1017:8 SCO MTU 64:0
  HCI Event: Command Complete (0x0e) plen 68
     Read Local Supported Commands (0x04|0x0002) ncmd 1
     status 0x00
     Commands: ffffff03feffcfffffffffff0300f8ff07
  HCI Event: Command Complete (0x0e) plen 4
     Delete Stored Link Key (0x03|0x0012) ncmd 1
     status 0x11 deleted 2048
     Error: Unsupported Feature or Parameter Value

From the looks of it, this device seems genuine and not one of the
devices that are neither Broadcom nor CSR devices in reality.

T: Bus=04 Lev=02 Prnt=02 Port=02 Cnt=02 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0a5c ProdID=2045 Rev= 1.12
S: Manufacturer=Broadcom Corp
S: Product=BCM2045A
S: SerialNumber=000000000000
C:* #Ifs= 4 Cfg#= 1 Atr=a0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=00 Driver=(none)
Reported-and-tested-by: NJulio González Mejías <juliolokooo@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

For the older controllers like Wilkens Peak and Stone Peak, enabling the
traces requires to switch into manufacturer mode first. This patch does
exactly that, but only for these older controllers.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

For Intel controllers the diagnostics settings are not persistent over
HCI Reset. So set the quirk to programm them again on every power up.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The change to bpa10x to use the h4_recv_buf helper added a dependency
on BT_HCIUART. This was incorrectly added to Kconfig by adding a
'select' statement, which now in turn causes build failures
when CONFIG_TTY is not set:

warning: (BT_HCIBPA10X) selects BT_HCIUART which has unmet direct dependencies (NET && BT && TTY)
vers/built-in.o: In function `hci_uart_tty_receive':
fpga-mgr.c:(.text+0x282824): undefined reference to `tty_unthrottle'
drivers/built-in.o: In function `hci_uart_tty_ioctl':
fpga-mgr.c:(.text+0x282aa0): undefined reference to `n_tty_ioctl_helper'
drivers/built-in.o: In function `hci_uart_flush':

This replaces the 'select BT_HCIUART' dependency with 'depends on', which
does not have this kind of problem. Alternatively, one could add 'depends
on TTY', but avoiding 'select' on user-visible options is generally the
preferred choice as that does not introduce the potential for dependency
loops or incomplete dependency chains.

Fixes: 91489919 ("Bluetooth: bpa10x: Fix missing BT_HCIUART dependency")
Fixes: 943cc592 ("Bluetooth: bpa10x: Use h4_recv_buf helper for frame reassembly")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The lock states from Intel SfP controllers can only be read once before
loading the firmware. So for debugging purposes, print them out.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

For Intel controllers with firmware that allows tracing of baseband
functionality this allows enabling it via set_diag driver callback.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The Broadcom Bluetooth USB devices have a third interface that is
dedicated for LM_DIAG messages. The If#= 2 describes this interface
and it consists of one bulk in and one bulk endpoint.

T:  Bus=01 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 38 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=19ff ProdID=0239 Rev= 1.12
S:  Manufacturer=Broadcom Corp
S:  Product=BCM20702A0
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=btusb
E:  Ad=84(I) Atr=02(Bulk) MxPS=  32 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=  32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)

For all Broadcom based devices with this interface, the driver now
claims it and schedules URBs for it. This allows to capture the
LM_DIAG messages and allows forwarding them via hci_recv_diag into
the diagnostic channel of the Bluetooth subsystem.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Selecting just BT_HCIUART_H4 is not enough and it also needs to select
BT_HCIUART to avoid this warning:

warning: (BT_HCIBPA10X) selects BT_HCIUART_H4 which has unmet direct
dependencies (NET && BT && BT_HCIUART)
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The manually coded frame reassembly is actually broken. The h4_recv_buf
helper from the UART driver is a perfect fit for frame reassembly for
this driver. So just export that function and use it here as well.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The BPA-10x devices support tracing operation. Use the set_diag driver
callback to allow enabling and disabling that functionality.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

For debugging pruposes, read the revision string of the BPA-10x devices
and print it. For example one of the latest devices respond with the
string SNIF_102,BB930,02/01/18,10:37:56.

  < HCI Command: Vendor (0x3f|0x000e) plen 1
          07                                               .
  > HCI Event: Command Complete (0x0e) plen 49
        Vendor (0x3f|0x000e) ncmd 1
          Status: Success (0x00)
          53 4e 49 46 5f 31 30 32 2c 42 42 39 33 30 2c 30  SNIF_102,BB930,0
          32 2f 30 31 2f 31 38 2c 31 30 3a 33 37 3a 35 36  2/01/18,10:37:56
          00 00 00 00 00 00 00 00 00 00 00 00 00           .............
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The set_diag driver callback allows enabling and disabling the vendor
specific diagnostic information. Since Broadcom chips have support for
a dedicated LM_DIAG channel, hook it up accordingly.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The Broadcom UART based controllers can send LM_DIAG messages with the
identifier 0x07 inside the HCI stream. These messages are 63 octets in
size and have no variable payload or length indicator.

This patch adds correct parsing information for the h4_recv_buf handler
and in case these packets are received, they are forwarded to the
Bluetooth core via hci_recv_diag interface.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The Broadcom Bluetooth controllers have the chip name included in the
ROM firmware or later in the patchram firmware. For debugging purposes
read the local name and print it out. This is only done during setup
stage and only once before loading the firmware and once after loading
the firmware.

For the Broadcom based controllers from Apple, the name is only read once
after determining the chip id.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Setting and clearing of HCI_RUNNING flag in each and every driver is
just duplicating the same code all over the place. So instead of having
the driver do it in their hdev->open and hdev->close callbacks, set it
globally in the core transport handling.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

In all callbacks for hdev->send the status of HCI_RUNNING is checked. So
instead of repeating that code in every driver, move the check into the
hci_send_frame function before calling hdev->send.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The commit 7bee8b08 allows the Read Verbose Config Info to fail
gracefully and not cause the controller setup to abort. It seems the
reason that command failed in the first place was the missing HCI Reset
to bring the controller in full Bluetooth mode.

Apple Bluetooth controllers start out in HID mode and when in that mode
the Read Verbose Config Info command is not allowed. Sending HCI Reset
switches the controller into full HCI mode.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Add regmap ibt to support Intel Bluetooth silicon register access
over HCI. Intel BT/FM combo chip allows to read/write some registers
(e.g. FM registers) via its HCI interface.

Read/Write operations are performed via a HCI transaction composed of
a HCI command (host->controller) followed by a HCI command complete
event (controller->host). Read/Write Command opcodes can be specified
to the regmap init function.
We define data formats which are intel/vendor specific.

Register Read/Write HCI command payload (Host):
Field: | REG ADDR | MODE | DATA_LEN | DATA... |
size:  |   32b    |  8b  |    8b    |  8b*    |

Register Read HCI command complete event payload (Controller):
Field: | CMD STATUS | REG ADDR | DATA... |
size:  |     8b     |   32b    |  8b*    |

Register Write HCI command complete event payload (Controller):
Field: | CMD_STATUS |
size:  |     8b     |

Since this payload is HCI encapsulated, Little Endian byte order is
used.

Write/Read Example:

If we write 0x0000002a at address 0x00008c04, with opcode_write 0xfc5d,
The resulting transaction is (btmon trace):

< HCI Command (0x3f|0x005d) plen 10 [hci0]
        04 8c 00 00 02 04 2a 00 00 00
> HCI Event (0x0e) plen 4
      Unknown (0x3f|0x005d) ncmd 1
        00

Then, if we read the same register with opcode_read 0xfc5e:

< HCI Command (0x3f|0x005e) plen 6 [hci0]
        04 8c 00 00 02 04
> HCI Event (0x0e) plen 12 [hci0]
      Unknown (0x3f|0x005e) ncmd 1
        00 04 8c 00 00 2a 00 00 00
Signed-off-by: NLoic Poulain <loic.poulain@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This device has always ACPI companion because driver supports only ACPI
enumeration. Therefore there is no need to test it in bcm_acpi_probe() and
we can pass it directly to acpi_dev_get_resources() (which will return
-EINVAL in case of NULL argument is passed).
Signed-off-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Tree wide grep for "hci_bcm" doesn't reveal there is any code registering
this platform device and "struct acpi_device_id" use for passing the
platform data looks a debug/test code leftover to me.

I'm assuming this driver effectively supports only ACPI enumeration and
thus test for ACPI_HANDLE() and platform data can be removed.
Signed-off-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

There is no need to call acpi_match_device() in driver's probe path and
verify does it find a match to given ACPI _HIDs in .acpi_match_table as
driver/platform/acpi core code has found the match prior calling the probe.
Signed-off-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Driver doesn't handle possible error from acpi_dev_get_resources(). Test it
and return the error code in case of error.
Signed-off-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Caller of acpi_dev_get_resources() should free the constructed resource
list by calling the acpi_dev_free_resource_list() in order to avoid memory
leak.
Signed-off-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

There is some unneeded code in "hci_intel" probing. First
acpi_match_device() call is needless as driver/platform/acpi core code has
already done the matching before calling the probe and the driver does not
use the returned pointer to matching _HID other than checking is it NULL.

Then tree wide grep for "hci_intel" doesn't reveal that there is any code
registering this platform device so it looks this device is always backed
with ACPI companion so also ACPI_HANDLE() test can be removed.
Signed-off-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch fixes checkpatch warnings:
- Comparison to NULL could be re-written
- no space required after a cast
Signed-off-by: NPrasanna Karthik <mkarthi3@visteon.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Use <linux/io.h> instead of <asm/io.h>, fixes checkpatch
Warning;
Signed-off-by: NPrasanna Karthik <mkarthi3@visteon.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

'retransmit' being set in HCI_IBS_TX_WAKING case, using bool would be
efficient. Initialize local bool to false.
Signed-off-by: NPrasanna Karthik <mkarthi3@visteon.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

NOT NULL comparison modified to be readable, reported
by checkpatch.
Signed-off-by: NPrasanna Karthik <mkarthi3@visteon.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

NOT NULL comparison modified to be readable, reported
by checkpatch.
Signed-off-by: NPrasanna Karthik <mkarthi3@visteon.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

NOT NULL comparison modified to be readable, reported
by checkpatch.
Signed-off-by: NPrasanna Karthik <mkarthi3@visteon.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>