This patch adds support for 25G Active Optical Cables (AOC) and Active
Copper Cables (ACC) PHY types.
Signed-off-by: NSudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Signed-off-by: NKrzysztof Malek <krzysztof.malek@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This separates the setting of autoneg in i40e_phy_types_to_ethtool into
its own conditional.  Doing this adds clarity as what PHYs
support/advertise autoneg and makes it easier to add new PHY types in
the future.

This also fixes an issue on devices with CRT_RETIMER where advertising
autoneg was being set, but supported autoneg was not.
Signed-off-by: NAlan Brady <alan.brady@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There's a number of minor incidental whitespace issues in this file.
This addresses most of the ones I could find.
Signed-off-by: NAlan Brady <alan.brady@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Someone forgot a word in this comment and it's confusing without it.
Signed-off-by: NAlan Brady <alan.brady@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The function header erroneously listed 'phy_types' as a parameter.  The
correct parameter is 'pf'.
Signed-off-by: NAlan Brady <alan.brady@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This fixes two issues in i40e_get_link_ksettings.  It adds calls to
ethtool_link_ksettings_zero_link_mode to make sure advertising and
supported link masks are cleared before we start setting bits in them.

This also replaces some funky bit manipulations with a much nicer call
to ethtool_link_ksettings_del_link_mode when removing link modes.
Signed-off-by: NAlan Brady <alan.brady@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Someone left this poor little function naked with no header.  This
dresses it up in a proper function header it deserves.
Signed-off-by: NAlan Brady <alan.brady@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This 'ifdef' doesn't accomplish anything so remove it.
Signed-off-by: NAlan Brady <alan.brady@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

After the switch to the new ethtool API, ethtool passes us
ethtool_ksettings structs instead of ethtool_command structs, however we
were still referring to them as 'cmd' variables.  This renames them to
'ks' variables which makes the code easier to understand.
Signed-off-by: NAlan Brady <alan.brady@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Formerly, IPIP entries were created lazily by next hops that referenced
an offloadable IP-in-IP netdevice. However now that they are created
eagerly as a reaction to events on such netdevices, the reference
counting is useless. Hence drop it.

The routes whose next hops reference an offloaded IP-in-IP netdevice
actually linger around a bit after their device is unregistered.
However, mlxsw_sp_ipip_entry_destroy() also destroys the backing
loopback, and mlxsw_sp_rif_destroy() transitively (via
mlxsw_sp_nexthop_rif_gone_sync()) calls mlxsw_sp_nexthop_ipip_fini(),
which unlinks the IPIP entry from a next hop. Thus no dangling pointers
are left behind for the brief window after netdevice is gone, but routes
not yet.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

IPIP entries are created as soon as an offloadable device is created.
That means that when such a device is later moved to a different VRF,
the loopback device that backs the tunnel is wrong.

Thus when an offloadable encapsulating netdevice moves from one VRF to
another, make sure that the loopback is updated as necessary.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Current code for offloading IP-in-IP tunneling assumes that there is no
decap without encap. But that's never true for IPv6 overlays, and is not
true for IPv4 ones either, if net.ipv4.conf.*.rp_filter is unset.

To support decap-only tunnels, an IPIP entry is now created as soon as
an offloadable tunneling device is created. When that netdevice is up'd,
a decap route is looked up and possibly offloaded. Thus decap is not
handled implicitly as part of mlxsw_sp_ipip_entry_get() call anymore,
but needs to be done explicitly after the get, if desired.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NPetr Machata <petrm@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

So far, all netdevice notifications that the driver cared about were
related to its own ports, and mlxsw_sp could be retrieved from the
netdevice's private data. For IP-in-IP offloading however, the driver
cares about events on foreign netdevices, and getting at mlxsw_sp or
router data structures from the handler is inconvenient.

Therefore move the netdevice notifier blocks from global scope to struct
mlxsw_sp to allow retrieval from the notifier block pointer itself.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The notifier cause a link error when NET_DSA is a loadable
module:

drivers/net/ethernet/broadcom/bcmsysport.o: In function `bcm_sysport_remove':
bcmsysport.c:(.text+0x1582): undefined reference to `unregister_dsa_notifier'
drivers/net/ethernet/broadcom/bcmsysport.o: In function `bcm_sysport_probe':
bcmsysport.c:(.text+0x278d): undefined reference to `register_dsa_notifier'

This adds a dependency that forces the systemport driver to be
a loadable module as well when that happens, but otherwise
allows it to be built normally when DSA is either built-in or
completely disabled.

Fixes: d1565763 ("net: systemport: Establish lower/upper queue mapping")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Modify baycom driver to use the new parallel port device model.
Signed-off-by: NSudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This removes custom flag handling.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch updates the pkt_type to PACKET_HOST only if the destination MAC
address matches on the on the source based macvlan. It didn't make sense to
be updating broadcast, multicast, and non-local destined frames with
PACKET_HOST.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch intoduces a slight adjustment for macvlan to address the fact
that in source mode I was seeing two copies of any packet addressed to the
macvlan interface being delivered where there should have been only one.

The issue appears to be that one copy was delivered based on the source MAC
address and then the second copy was being delivered based on the
destination MAC address. To fix it I am just treating a unicast address
match as though it is not a match since source based macvlan isn't supposed
to be matching based on the destination MAC anyway.

Fixes: 79cf79ab ("macvlan: add source mode")
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tx_table is part of the private data of kernel net_device. It is only
zero-ed out when allocating net_device.

We may recreate netvsc_device w/o recreating net_device, so the private
netdev data, including tx_table, are not zeroed. It may contain channel
numbers for the older netvsc_device.

This patch adds initialization of tx_table each time we recreate
netvsc_device.
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Simplify the variable name: tx_send_table
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rename this variable because it is the Receive indirection
table.
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The break statement for the Macronix case is missing and will
fall through to the Winbond case and re-assign the size setting.
Fix this by adding the missing break statement.  Also correctly
indent the return statements.

Detected by CoverityScan, CID#1458020 ("Missing break in switch")

Fixes: 96ac18f1 ("cxgb4: Add support for new flash parts")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Collect SGE, PCIE, PM, UP CIM, MA and HMA dumps.
Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Try to access TP indirect registers via firmware first.  If this fails,
fallback and access them directly.  This ensures that driver and
firmware do not conflict each other while accessing the TP indirect
registers.
Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Collect firmware mbox and device logs before collecting the rest of
the hardware dumps to snap the firmware state before the mailbox logs
are updated by other hardware dumps.
Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Collect EDC0 and EDC1 memory dump.
Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add base to collect dump entities.  Collect register dump and
update template header accordingly.
Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement operations to set/get dump data via ethtool.  Also add
template header that precedes dump data, which helps in decoding
and extracting the dump data.
Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Today's -next build encountered an error due to a missing definition of
WARN_ON(), caused by some header reorganization removing an implicit
inclusion of linux/bug.h.  Fix this with an explicit inclusion.
Signed-off-by: NMark Brown <broonie@kernel.org>
Acked-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The .set_addr function does nothing, remove the dsa_loop implementation
before getting rid of it completely in DSA.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As for mv88e6xxx, setup the switch from within the mv88e6060 driver with
a random MAC address, and remove the .set_addr implementation.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 88E6060 Ethernet switch always transmits the multicast bit of the
switch MAC address as a zero. It re-uses the corresponding bit 8 of the
register "Switch MAC Address Register Bytes 0 & 1" for "DiffAddr".

If the "DiffAddr" bit is 0, then all ports transmit the same source
address. If it is set to 1, then bit 2:0 are used for the port number.

The mv88e6060 driver is currently wrongly shifting the MAC address byte
0 by 9. To fix this, shift it by 8 as usual and clear its bit 0.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

An Ethernet switch may support having a MAC address, which can be used
as the switch's source address in transmitted full-duplex Pause frames.

If a DSA switch supports the related .set_addr operation, the DSA core
sets the master's MAC address on the switch. This won't make sense
anymore in a multi-CPU ports system, because there won't be a unique
master device assigned to a switch tree.

Instead, setup the switch from within the Marvell driver with a random
MAC address, and remove the .set_addr implementation.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Resources such as FT, QPN HT and mdev resources should be allocated
only by parent netdev. Shared resources are allocated and freed by the
parent interface since the parent is always present and created
before the IPoIB PKEY sub-interface.
Signed-off-by: NAlex Vesker <valex@mellanox.com>
Reviewed-by: NErez Shitrit <erezsh@mellanox.com>

Similar to VLAN interfaces child interfaces have limited ethtool
support. In current code the main limitation that does not
allow child interface ethtool configuration is due to shared
resources which are managed by the parent.
Signed-off-by: NAlex Vesker <valex@mellanox.com>
Reviewed-by: NErez Shitrit <erezsh@mellanox.com>

Child interface ndos will be called to support child interface
specific behaviour.

ndo_init flow:
-Acquire shared QPN to net-device HT from parent
-Continue with the same flow as parent interface

ndo_open flow:
-Initialize child underlay QP and connect to shared FT
-Create child send TIS
-Open child send channels
Signed-off-by: NAlex Vesker <valex@mellanox.com>
Reviewed-by: NErez Shitrit <erezsh@mellanox.com>

Child interface profile will be called to support child interface
specific behaviour. The child code is sparse compared to the parent
since the RX channels are shared between the interfaces.
Creating a septate profile for child and parent will make a smother
code with a better ability for future expansion.
The profile stuct is exposed to the parent using a getter function.
Signed-off-by: NAlex Vesker <valex@mellanox.com>
Reviewed-by: NErez Shitrit <erezsh@mellanox.com>