Also convert to use generic kernel/power/Kconfig to make the use of the
shared APM emulation possible.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The following macro :
include/asm-powerpc/vga.h:#define VGA_MAP_MEM(x,s) (x + vgacon_remap_base)
is used by drivers/video/console/vgacon.c which can be compiled as a module
(drivers/video/vga16fb.ko).

Therefore, vgacon_remap_base should be exported.
Signed-off-by: NMathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

arch/powerpc/mm/mem.c states that page_is_ram is called by the code that
implements /dev/mem, which isn't true.  Remove the comment.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

kernel/irq.c contains a comment that speaks of -1 and -2 as interrupt
numbers, but this is actually dependent on configuration options now.
Replace by NO_IRQ and NO_IRQ_ENABLED.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Use ARRAY_SIZE macro already defined in linux/kernel.h
Signed-off-by: NAhmed S. Darwish <darwish.07@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NKumar Gala <galak@gate.crashing.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Use ARRAY_SIZE macro already defined in linux/kernel.h
Signed-off-by: NAhmed S. Darwish <darwish.07@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

In preparation for marking file_operations as const.

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NArjan van de Ven <arjan@infradead.org>
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Use the appropriate logging macro for the priority level for that
printk call.
Signed-off-by: NRobert P. J. Day <rpjday@mindspring.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NSylvain Munaut <tnt@246tNt.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The previous patch changing pSeries to use H_BULK_REMOVE broke the
JS20 blade, where the firmware doesn't support H_BULK_REMOVE.  This
adds a firmware check so that on machines that don't have H_BULK_REMOVE,
we just use the H_REMOVE call as before.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The arch hooks arch_setup_msi_irq and arch_teardown_msi_irq are now
responsible for allocating and freeing the linux irq in addition to
setting up the the linux irq to work with the interrupt.

arch_setup_msi_irq now takes a pci_device and a msi_desc and returns
an irq.

With this change in place this code should be useable by all platforms
except those that won't let the OS touch the hardware like ppc RTAS.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Acked-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

We need to be able to get from an irq number to a struct msi_desc.
The msi_desc array in msi.c had several short comings the big one was
that it could not be used outside of msi.c.  Using irq_data in struct
irq_desc almost worked except on some architectures irq_data needs to
be used for something else.

So this patch adds a msi_desc pointer to irq_desc, adds the appropriate
wrappers and changes all of the msi code to use them.

The dynamic_irq_init/cleanup code was tweaked to ensure the new
field is left in a well defined state.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Acked-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

pci_scan_msi_device() doesn't do anything anymore, so remove it.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Since isa_bridge is neither assigned any value !NULL nor used on !Alpha, 
there's no reason for providing it.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

USB OHCI driver bus glue for the PS3 game console.
Signed-off-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

USB EHCI driver bus glue for the PS3 game console.
Signed-off-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When we do full FP emulation its possible that we need to post a SIGFPE based
on the results of the emulation.  The previous code ignored this case completely.

Additionally, the Soft_emulate_8xx case had two issues.  One, we should never
generate a SIGFPE since the code only does data movement.  Second, we were
interpreting the return codes incorrectly, it returns 0 on success, 1 on
illop and -EFAULT on a data access error.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Anytime we are emulating an instruction we are going to be doing some form of
get_user() to get the instruction image to decode.  Since get_user() might
sleep we need to ensure we have interrupts enabled or we might see something
like:

Debug: sleeping function called from invalid context at arch/powerpc/kernel/traps.c:697
in_atomic():0, irqs_disabled():1
Call Trace:
[D6023EB0] [C0007F84] show_stack+0x58/0x174 (unreliable)
[D6023EE0] [C0022C34] __might_sleep+0xbc/0xd0
[D6023EF0] [C000D158] program_check_exception+0x1d8/0x4fc
[D6023F40] [C000E744] ret_from_except_full+0x0/0x4c
--- Exception: 700 at 0x102a7100
    LR = 0xdb9ef04

However, we want to ensure that interrupts are disabled when handling a trap
exception that might be used for a kernel breakpoint.  This is why ProgramCheck
is marked as EXC_XFER_STD instead of EXC_XFER_EE.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Added kprobes to ppc32 platforms that have use single_step_exception.  This
excludes 4xx and anything Book-E since their debug mechanisms for single stepping
are completely different.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

H_BULK_REMOVE lets us remove 4 entries from the MMU hash table with one
hypervisor call.  This uses it in pSeries_lpar_hpte_invalidate so we
can tear down mappings with fewer hypervisor calls.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Some instruction tracing tools use the RI (recoverable interrupt) bit
in the MSR to indicate when it's safe to single-step.  Currently we
clear RI after restoring r13 when returning to userspace.  However,
if we single-step past the point where r13 is restored, we'll corrupt
r13 in the exception entry code and not restore it.  This moves the
clearing of RI to just before r13 is restored so this doesn't happen.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

To the issue: some point during 2.6.20 development, Paul Mackerras
introduced the "lazy IRQ  disabling" patch (very cool work,  BTW).
In that patch, the performance monitor unit exception was marked as
"maskable", in the sense that if interrupts were soft-disabled, that
exception could be ignored.  This broke my PowerPC profiling code.
The symptom that I see is that a varying number of interrupts
(from 0 to $n$, typically closer to 0) get delivered, when, in
reality, it should always be very close to $n$.

The issue stems from the way masking is being done.   Masking in
this fashion seems to  work well with the decrementer and external
interrupts, because they are raised again until "really"  handled.
For the PMU, however, this does not apply (at least on my Xserver
machine with a 970FX processor).  If the PMU exception is not handled,
it will _not_ be re-raised (at least on my machine).  The documentation
states that the PMXE bit in MMCR0 is set to 0 when the PMU exception
is raised.  However, software must re-set the bit to re-enable PMU
exceptions.  If the exception is ignored (as currently) not only is
that interrupt lost, but because software does not re-set PMXE, the
PMU registers are "frozen" forever.

[This patch means that performance monitor exceptions are taken and
handled even if irqs are off, as long as some other interrupt hasn't
come along and caused interrupts to be hard-disabled.  In this sense
the PMU exception becomes like an NMI.  The oprofile code for most
powerpc processors does nothing that is unsafe in an NMI context, but
the Cell oprofile code does a spin_lock_irqsave.  However, that turns
out to be OK because Cell doesn't actually use the performance
monitor exception; performance monitor interrupts come in as a
regular interrupt on Cell, so will be disabled when irqs are off.
 -- paulus.]
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The new dcr code does not currently compile when configured for native
DCR access on ARCH=powerpc.  This patch fixes the problems.
Signed-off-by: NDavid Gibson <dwg@au1.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Some systems supported by the maple platform (e.g. JS2x blades running
SLOF) are able to use the mmio_nvram backend for reading and writing
nvram.  This is an improvement over the current situation -- no nvram
access from userspace at all.

Select MMIO_NVRAM for the maple platform.

Initialize the mmio_nvram backend from maple setup code.
Signed-off-by: NNathan Lynch <ntl@pobox.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Base pasemi defconfig. Nothing special, just the native drivers plus
common PCI-express/PCI cards.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

I/O TLB support for PA6T-1682M.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The DMA controller on PWRficient is somewhat special -- has a PCI header
so it looks like it's on the root PCI (-Express) root bus, but it uses
more than the default number of interrupts (and they are hardwired).

We need to wire up all interrupts for the DMA controller. The generic
IRQ code will only map the primary interrupt from the PCI header (128),
so add 129->211 by hand.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Timebase update is simple on PA6T, since global updates can be done from
one core by writing to an SPR.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Implement reset on platforms/pasemi. Default is just to reset the
cpu using the SDC registers.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Powersave support on PA6T. Right now it only uses 'doze' mode, and
will default to no savings (spin).
Signed-off-by: NOlof Johansson <olof@lixom.net>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Print out decoded machine check information on PA6T.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Early debug output for PA Semi UART. Uses the 2.05 CI real mode ops.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

G3 Blue & White is misconfigured by default so that CardBus controllers
in PCI slots don't work.  The PCI bridge is programmed to only allow
access to bus 1 but not higher busses.

The patch forces the PCI busses to be reassigned if a Grackle controller
is found and the machine identifies itself as "PowerMac1,1"
Signed-off-by: NPavel Roskin <proski@gnu.org>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This patch creates defconfig file for Celleb platform.
Signed-off-by: NKou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This patch adds base support for Celleb platform.
Signed-off-by: NKou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

SPU support routines for Celleb platform.
Signed-off-by: NKou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Spu management ops in arch/platforms/cell/spu_priv1_mmio.h can be used
commonly in of based platform. This patch separates spu management ops
from native cell code and uses on celleb platform.
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: NKou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This patch adds udbg support for Celleb platform.
Signed-off-by: NKou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>