This patch delays the (ACPI S3) suspend while the TPM is busy processing a
command and the TPM TIS driver is run in interrupt mode. This is the same
behavior as we already have it for the TPM TIS driver in polling mode.

Reasoning: Some of the TPM's commands advance the internal state of the TPM.
An example would be the extending of one of its PCR registers. Upper layers,
such as IMA or TSS (TrouSerS), would certainly want to be sure that the
command succeeded rather than getting an error code (-62 = -ETIME) that may
not give a conclusive answer as for what reason the command failed. Reissuing
such a command would put the TPM into the wrong state, so waiting for it to
finish is really the only option.

The downside is that some commands (key creation) can take a long time and
actually prevent the machine from entering S3 at all before the 20 second
timeout of the power management subsystem arrives.
Signed-off-by: NStefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: NRajiv Andrade <srajiv@linux.vnet.ibm.com>

This patch makes sure that if the TPM TIS interface is run in interrupt mode
(rather than polling mode) that all interrupts are enabled in the TPM's
interrupt enable register after a resume from ACPI S3 suspend. The registers
may either have been cleared by the TPM loosing its state during device sleep
or by the BIOS leaving the TPM in polling mode (after sending a command to
the TPM for starting it up again)

You may want to check if your TPM runs with interrupts by doing

cat /proc/interrupts | grep -i tpm

and see whether there is an entry or otherwise for it to use interrupts:

modprobe tpm_tis interrupts=1 [add 'itpm=1' for Intel TPM ]

v2:
  - the patch was adapted to work with the pnp and platform driver
    implementations in tpm_tis.c
Signed-off-by: NStefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: NRajiv Andrade <srajiv@linux.vnet.ibm.com>

This patch fixes the TPM's pubek sysfs entry that is accessible as long
as the TPM doesn't have an owner. It was necessary to shift the access to the
data by -10 -- the first byte immediately follows the 10 byte header. The
line

 	data = tpm_cmd.params.readpubek_out_buffer;

sets it at the offset '10' in the packet, so we can read the data array
starting at offset '0'.

Before:

Algorithm: 00 0C 00 00
Encscheme: 08 00
Sigscheme: 00 00
Parameters: 00 00 00 00 01 00 AC E2 5E 3C A0 78
Modulus length: -563306801
Modulus:
28 21 08 0F 82 CD F2 B1 E7 49 F7 74 70 BE 59 8C
43 78 B1 24 EA 52 E2 FE 52 5C 3A 12 3B DC 61 71
[...]

After:

Algorithm: 00 00 00 01
Encscheme: 00 03
Sigscheme: 00 01
Parameters: 00 00 08 00 00 00 00 02 00 00 00 00
Modulus length: 256
Modulus:
AC E2 5E 3C A0 78 DE 6C 9E CF 28 21 08 0F 82 CD
F2 B1 E7 49 F7 74 70 BE 59 8C 43 78 B1 24 EA 52
[...]
Signed-off-by: NStefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: NRajiv Andrade <srajiv@linux.vnet.ibm.com>

Display the TPM's interface timeouts in a 'timeouts' sysfs entry. Display
the entries as having been adjusted when they were scaled due to their values
being reported in milliseconds rather than microseconds.
Signed-off-by: NStefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: NRajiv Andrade <srajiv@linux.vnet.ibm.com>

Adjust the interface timeouts if they are found to be too small, i.e., if
they are returned in milliseconds rather than microseconds as we heared
from Infineon that some (old) Infineon TPMs do.
Signed-off-by: NStefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: NRajiv Andrade <srajiv@linux.vnet.ibm.com>

The TPM driver currently discards the interface timeout values returned
from the TPM. The check of the response packet needs to consider that
the return_code field is 0 on success and the size of the expected
packet is equivalent to the header size + u32 length indicator for the
TPM_GetCapability() result + 4 interface timeout indicators of type u32.
Signed-off-by: NStefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: NRajiv Andrade <srajiv@linux.vnet.ibm.com>

Display the TPM's command timeouts in a 'durations' sysfs entry. Display
the entries as having been adjusted when they were scaled due to their values
being reported in milliseconds rather than microseconds.
Signed-off-by: NStefan Berger <stefanb@linux.vnet.ibm.com>
Tested-by: NGuillaume Chazarain <guichaz@gmail.com>
Signed-off-by: NRajiv Andrade <srajiv@linux.vnet.ibm.com>

Adjust the durations if they are found to be too small, i.e., if they are
returned in milliseconds rather than microseconds as some Infineon TPMs are
reported to do.
Signed-off-by: NStefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: NRajiv Andrade <srajiv@linux.vnet.ibm.com>

The TPM driver currently discards the durations values returned
from the TPM. The check of the response packet needs to consider that
the return_code field is 0 on success and the size of the expected
packet is equivalent to the header size + u32 length indicator for the
TPM_GetCapability() result + 3 timeout indicators of type u32.

v4:
- sysfs entry 'durations' is now a patch of its own
- the work-around for TPMs reporting durations in milliseconds is now in a
  patch of its own

v3:
- sysfs entry now called 'durations' to resemble TPM-speak (previously
  was called 'timeouts')

v2:
- adjusting all timeouts for TPM devices reporting timeouts in msec rather
  than usec
- also displaying in sysfs whether the timeouts are 'original' or 'adjusted'
Signed-off-by: NStefan Berger <stefanb@linux.vnet.ibm.com>
Tested-by: NGuillaume Chazarain <guichaz@gmail.com>
Signed-off-by: NRajiv Andrade <srajiv@linux.vnet.ibm.com>

Enable conditional ACL by passing object's pointers.
Signed-off-by: NTetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: NJames Morris <jmorris@namei.org>

This patch adds support for permission checks using argv[]/envp[] of execve()
request. Hooks are in the last patch of this pathset.
Signed-off-by: NTetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: NJames Morris <jmorris@namei.org>

This patch adds support for permission checks using executable file's realpath
upon execve() and symlink's target upon symlink(). Hooks are in the last patch
of this pathset.
Signed-off-by: NTetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: NJames Morris <jmorris@namei.org>

This patch adds support for permission checks using file object's DAC
attributes (e.g. owner/group) when checking file's pathnames. Hooks for passing
file object's pointers are in the last patch of this pathset.
Signed-off-by: NTetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: NJames Morris <jmorris@namei.org>

This patch adds support for permission checks using current thread's UID/GID
etc. in addition to pathnames.
Signed-off-by: NTetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: NJames Morris <jmorris@namei.org>

/sys/kernel/security/tomoyo/.domain_status can be easily emulated using
/sys/kernel/security/tomoyo/domain_policy . We can remove this interface by
updating /usr/sbin/tomoyo-setprofile utility.
Signed-off-by: NTetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: NJames Morris <jmorris@namei.org>

Commit eadd99cc "TOMOYO: Add auditing interface." by error replaced
"struct tomoyo_request_info"->domain with tomoyo_domain().
Signed-off-by: NTetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: NJames Morris <jmorris@namei.org>

Move keys-ecryptfs.txt to Documentation/security.
Signed-off-by: NMimi Zohar <zohar@us.ibm.com>
Signed-off-by: NJames Morris <jmorris@namei.org>

Sort by alphabetic order.
Signed-off-by: NTetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: NJames Morris <jmorris@namei.org>

Signed-off-by: NTetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: NJames Morris <jmorris@namei.org>

I forgot to add #ifndef in commit 0e4ae0e0 "TOMOYO: Make several options
configurable.", resulting

  security/built-in.o: In function `tomoyo_bprm_set_creds':
  tomoyo.c:(.text+0x4698e): undefined reference to `tomoyo_load_policy'

error.
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NTetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: NJames Morris <jmorris@namei.org>

Merge branch 'for-security' of git://git.kernel.org/pub/scm/linux/kernel/git/jj/apparmor-dev into next

* 'kvm-updates/3.0' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: x86 emulator: fix %rip-relative addressing with immediate source operand

* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  i2c/pca954x: Initialize the mux to disconnected state
  i2c-taos-evm: Fix log messages

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  arch/powerpc: use printk_ratelimited instead of printk_ratelimit
  powerpc/rtas-rtc: remove sideeffects of printk_ratelimit
  powerpc/pseries: remove duplicate SCSI_BNX2_ISCSI in pseries_defconfig
  powerpc/e500: fix breakage with fsl_rio_mcheck_exception
  powerpc/p1022ds: fix audio-related properties in the device tree
  powerpc/85xx: fix NAND_CMD_READID read bytes number

It's not so much an error as a warning about normal Marvell crazines.
So don't use KERN_ERR that ends up spamming the console even in quiet
mode, it's not _that_ critical.

Explained by Jeff:

 "Long explanation, it's a mess:

  Marvell took standard AHCI, and bastardized it to include a weird mode
  whereby PATA devices appear inside the AHCI DMA and interrupt
  infrastructure you're familiar with.

  So, PATA devices appear via pata_marvell driver, using basic legacy
  IDE programming interface.  But SATA devices, which might also be
  attached to this chip, either work in under-performing mode or
  simply don't work at all (e.g.  newer 6 Gbps devices or port
  multiplier attachments, NCQ, ...)

  On the other hand, 'ahci' driver loads and works with the chip's
  attached SATA devices quite beautifully, but is completely unable to
  drive any attached PATA devices, due to the Marvell-specific
  PATA-under-AHCI interface.

  The "masking port_map 0x7 -> 0x3" message is the ahci driver "hiding"
  the PATA port(s) from itself, making sure it will only drive the SATA
  ports it knows how to drive."
Acked-by: NJeff Garzik <jgarzik@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

pca954x power-on default is channel 0 connected. If multiple pca954x
muxes are connected to the same physical I2C bus, the parent bus will
see channel 0 devices behind both muxes by default. This is bad.

Scenario:
            -- pca954x @ 0x70 -- ch 0 (I2C-bus-101) -- EEPROM @ 0x50
            |
I2C-bus-1 ---
            |
            -- pca954x @ 0x71 -- ch 0 (I2C-bus-111) -- EEPROM @ 0x50

1. Load I2C bus driver: creates I2C-bus-1
2. Load pca954x driver: creates virtual I2C-bus-101 and I2C-bus-111
3. Load eeprom driver
4. Try to read EEPROM @ 0x50 on I2C-bus-101. The transaction will also bleed
   onto I2C-bus-111 because pca954x @ 0x71 channel 0 is connected by default.

Fix: Initialize pca954x to disconnected state in pca954x_probe()
Signed-off-by: NPetri Gynther <pgynther@google.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org

* Print all error and information messages even when debugging is
  disabled.
* Don't use adapter device to log messages before it is ready.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org

%rip-relative addressing is relative to the first byte of the next instruction,
so we need to add %rip only after we've fetched any immediate bytes.

Based on original patch by Li Xin <xin.li@intel.com>.
Signed-off-by: NAvi Kivity <avi@redhat.com>
Acked-by: NLi Xin <xin.li@intel.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

Since printk_ratelimit() shouldn't be used anymore (see comment in
include/linux/printk.h), replace it with printk_ratelimited.
Signed-off-by: NChristian Dietrich <christian.dietrich@informatik.uni-erlangen.de>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Don't use printk_ratelimit() as an additional condition for returning
on an error. Because when the ratelimit is reached, printk_ratelimit
will return 0 and e.g. in rtas_get_boot_time won't check for an error
condition.
Signed-off-by: NChristian Dietrich <christian.dietrich@informatik.uni-erlangen.de>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

AppArmor is masking the capabilities returned by capget against the
capabilities mask in the profile.  This is wrong, in complain mode the
profile has effectively all capabilities, as the profile restrictions are
not being enforced, merely tested against to determine if an access is
known by the profile.

This can result in the wrong behavior of security conscience applications
like sshd which examine their capability set, and change their behavior
accordingly.  In this case because of the masked capability set being
returned sshd fails due to DAC checks, even when the profile is in complain
mode.

Kernels affected: 2.6.36 - 3.0.
Signed-off-by: NJohn Johansen <john.johansen@canonical.com>

The pointer returned from tracehook_tracer_task() is only valid inside
the rcu_read_lock.  However the tracer pointer obtained is being passed
to aa_may_ptrace outside of the rcu_read_lock critical section.

Mover the aa_may_ptrace test into the rcu_read_lock critical section, to
fix this.

Kernels affected: 2.6.36 - 3.0
Reported-by: NOleg Nesterov <oleg@redhat.com>
Cc: stable@kernel.org
Signed-off-by: NJohn Johansen <john.johansen@canonical.com>

To be able to start using enforcing mode from the early stage of boot sequence,
this patch adds support for activating access control without calling external
policy loader program. This will be useful for systems where operations which
can lead to the hijacking of the boot sequence are needed before loading the
policy. For example, you can activate immediately after loading the fixed part
of policy which will allow only operations needed for mounting a partition
which contains the variant part of policy and verifying (e.g. running GPG
check) and loading the variant part of policy. Since you can start using
enforcing mode from the beginning, you can reduce the possibility of hijacking
the boot sequence.

This patch makes several variables configurable on build time. This patch also
adds TOMOYO_loader= and TOMOYO_trigger= kernel command line option to boot the
same kernel in two different init systems (BSD-style init and systemd).
Signed-off-by: NTetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: NJames Morris <jmorris@namei.org>

To be able to start using enforcing mode from the early stage of boot sequence,
this patch adds support for built-in policy configuration (and next patch adds
support for activating access control without calling external policy loader
program).
Signed-off-by: NTetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: NJames Morris <jmorris@namei.org>

Show statistics such as last policy update time and last policy violation time
in addition to memory usage.
Signed-off-by: NTetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: NJames Morris <jmorris@namei.org>

Gather string constants to one file in order to make the object size smaller.
Use unsigned type where appropriate.
read()/write() returns ssize_t.
Signed-off-by: NTetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: NJames Morris <jmorris@namei.org>

Currently TOMOYO holds SRCU lock upon open() and releases it upon close()
because list elements stored in the "struct tomoyo_io_buffer" instances are
accessed until close() is called. However, such SRCU usage causes lockdep to
complain about leaving the kernel with SRCU lock held.

This patch solves the warning by holding/releasing SRCU upon each
read()/write(). This patch is doing something similar to calling kfree()
without calling synchronize_srcu(), by selectively deferring kfree() by keeping
track of the "struct tomoyo_io_buffer" instances.
Signed-off-by: NTetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: NJames Morris <jmorris@namei.org>

TOMOYO wants to use /proc/self/ rather than /proc/$PID/ if $PID matches current
thread's process ID in order to prevent current thread from accessing other
process's information unless needed.

But since procfs can be mounted on various locations (e.g. /proc/ /proc2/ /p/
/tmp/foo/100/p/ ), TOMOYO cannot tell that whether the numeric part in the
string returned by __d_path() represents process ID or not.

Therefore, to be able to convert from $PID to self no matter where procfs is
mounted, this patch changes pathname representations for filesystems which do
not support rename() operation (e.g. proc, sysfs, securityfs).

Examples:
  /proc/self/mounts => proc:/self/mounts
  /sys/kernel/security/ => sys:/kernel/security/
  /dev/pts/0 => devpts:/0
Signed-off-by: NTetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: NJames Morris <jmorris@namei.org>

Mauras Olivier reported that it is difficult to use TOMOYO in LXC environments,
for TOMOYO cannot distinguish between environments outside the container and
environments inside the container since LXC environments are created using
pivot_root(). To address this problem, this patch introduces policy namespace.

Each policy namespace has its own set of domain policy, exception policy and
profiles, which are all independent of other namespaces. This independency
allows users to develop policy without worrying interference among namespaces.
Signed-off-by: NTetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: NJames Morris <jmorris@namei.org>