The values are in TUs (1.024ms), not ms.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It's a little confusing to get the BSSID outside the function
and pass it in, when it's only needed for this function, so
change that.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Hopefully the last required fix ... disable beaconing
only on beaconing interfaces, and thus avoid calling
ieee80211_if_config for purely virtual interfaces
(those driver doesn't know about).
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We cannot currently hand off extra IEs to hw_scan, so reject
configuring extra IEs for probe request frames when hw_scan
is set.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Cc: Jouni Malinen <j@w1.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Make sure nobody passes in bogus values, and translate the values
(although it isn't necessary).
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Before we have a probe response frame (which is used as the
beacon too) there's no need to ask drivers to beacon, they
will not get a beacon anyway.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When a directed tim bit is set, mac80211 currently disables power save
ands sends a null frame to the AP. But if dynamic power save is
disabled, mac80211 will not enable power save ever gain. Fix this by
adding ps-poll functionality to mac80211. When a directed tim bit is
set, mac80211 sends a ps-poll frame to the AP and checks for the more
data bit in the returned data frames.

Using ps-poll is slower than waking up with null frame, but it's saves more
power in cases where the traffic is low. Userspace can control if either
ps-poll or null wakeup method is used by enabling and disabling dynamic
power save.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently mac80211 checks for the multicast tim bit from beacons,
disables power save and sends a null frame if the bit is set. This was
added to support ath9k. But this is a bit controversial because the AP will
send multicast frames immediately after the beacon and the time constraints
are really high. Relying mac80211 to be fast enough here might not be
reliable in all situations. And there's no need to send a null frame, AP
will send the frames immediately after the dtim beacon no matter what.

Also if dynamic power save is disabled (iwconfig wlan0 power timeout 0)
currently mac80211 disables power save whenever the multicast bit is set
but it's never enabled again after receiving the first multicast/broadcast
frame.

The current implementation is not usable on p54/stlc45xx and the
easiest way to fix this is to remove the multicast tim bit check
altogether. Handling multicast tim bit in host is rare, most of the
designs do this in firmware/hardware, so it's better not to have it in
mac80211. It's a lot better to do this in firmware/hardware, or if
that's not possible it could be done in the driver.

Also renamed the function to ieee80211_check_tim() to follow the style
of the file.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This issue happens only when we are associated with a 11n AP and power save
is enabled. In the function 'ieee80211_master_start_xmit', ps_disable_work
is queued where wake_queues is called. But before this work is executed,
we check if the queues are stopped in _ieee80211_tx and return TX_AGAIN to
ieee8011_tx which leads to the warning message.
This patch fixes this erroneous case.
Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

net/core/skbuff.c is a hodge-podge of symbol export placement.
Some of the exports are right after the definition of the
symbol being exported, others are clumped together into a big
group at the end of the file.

Make things consistent.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Current "RTNETLINK answers: Invalid argument" warning, while trying to
add multiq qdisc to non-multiqueue device, isn't very helpful and some
of these devs can be changed btw., so let's use a better errno.

With feedback from Stephen Hemminger <shemminger@vyatta.com>
Reported-by: NBadalian Vyacheslav <slavon@bigtelecom.ru>
Signed-off-by: NJarek Poplawski <jarkao2@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

> Kernel BUG at drivers/net/tun.c:444
> invalid opcode: 0000 [1] SMP
> last sysfs file: /class/net/lo/ifindex
> CPU 0
> Modules linked in: tun ipt_MASQUERADE iptable_nat ip_nat xt_state ip_conntrack
> nfnetlink ipt_REJECT xt_tcpudp iptable_filter d
> Pid: 6912, comm: qemu-kvm Tainted: G      2.6.18-128.el5 #1
> RIP: 0010:[<ffffffff886f57b0>]  [<ffffffff886f57b0>]
> :tun:tun_chr_readv+0x2b1/0x3a6
> RSP: 0018:ffff8102202c5e48  EFLAGS: 00010246
> RAX: 0000000000000000 RBX: ffff8102202c5e98 RCX: 0000000004010000
> RDX: ffff810227063680 RSI: ffff8102202c5e9e RDI: ffff8102202c5e92
> RBP: 0000000000010ff6 R08: 0000000000000000 R09: 0000000000000001
> R10: ffff8102202c5e94 R11: 0000000000000202 R12: ffff8102275357c0
> R13: ffff81022755e500 R14: 0000000000000000 R15: ffff8102202c5ef8
> FS:  00002ae4398db980(0000) GS:ffffffff803ac000(0000) knlGS:0000000000000000
> CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
> CR2: 00002ae4ab514000 CR3: 0000000221344000 CR4: 00000000000026e0
> Process qemu-kvm (pid: 6912, threadinfo ffff8102202c4000, task
> ffff81022e58d820)
> Stack:  00000000498735cb ffff810229d1a3c0 0000000000000000 ffff81022e58d820
>  ffffffff8008a461 ffff81022755e528 ffff81022755e528 ffffffff8009f925
>  000005ea05ea0000 ffff8102209d0000 00001051143e1600 ffffffff8003c00e
> Call Trace:
>  [<ffffffff8008a461>] default_wake_function+0x0/0xe
>  [<ffffffff8009f925>] enqueue_hrtimer+0x55/0x70
>  [<ffffffff8003c00e>] hrtimer_start+0xbc/0xce
>  [<ffffffff886f58bf>] :tun:tun_chr_read+0x1a/0x1f
>  [<ffffffff8000b3f3>] vfs_read+0xcb/0x171
>  [<ffffffff800117d4>] sys_read+0x45/0x6e
>  [<ffffffff8005d116>] system_call+0x7e/0x83
>
>
> Code: 0f 0b 68 40 62 6f 88 c2 bc 01 f6 42 0a 08 74 0c 80 4c 24 41
> RIP  [<ffffffff886f57b0>] :tun:tun_chr_readv+0x2b1/0x3a6
>  RSP <ffff8102202c5e48>
>  <0>Kernel panic - not syncing: Fatal exception

This crashed when an LRO packet generated by bnx2x reached a
tun device through the bridge.  We're supposed to drop it at
the bridge.  However, because the check was placed in br_forward
instead of __br_forward, it's only effective if we are sending
the packet through a single port.

This patch fixes it by moving the check into __br_forward.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the user creates IPv6 over IPv6 tunnel, the device name created
by the kernel isn't set to t->parm.name, which is referred as the
result of ioctl().
Signed-off-by: NNoriaki TAKAMIYA <takamiya@po.ntts.co.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When user tries to map all chunks given in argument, kernel
works on a copy of the chunkmap, but at the end it doesn't
check the copy, but the orginal one.
Signed-off-by: NQu Haoran <haoran.qu@6wind.com>
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes echoing if the socket that has sent the request to
create/update/delete an entry is not subscribed to any multicast
group. With the current code, ctnetlink would not send the echo
message via unicast as nfnetlink_send() would be skip.
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes an inconsistency in the current ctnetlink code
since NAT sequence adjustment bit can only be updated but not set
in the conntrack entry creation.

This patch is used by conntrackd to successfully recover newly
created entries that represent connections with helpers and NAT
payload mangling.
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes connection tracking handling for ICMPv6 messages
related to Stateless Address Autoconfiguration, MLD, and MLDv2. They
can not be tracked because they are massively using multicast (on
pre-defined address). But they are not invalid and should not be
detected as such.
Signed-off-by: NEric Leblond <eric@inl.fr>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch fixes a typo in the inverse mapping of Node Information
request. Following draft-ietf-ipngwg-icmp-name-lookups-09, "Querier"
sends a type 139 (ICMPV6_NI_QUERY) packet to "Responder" which answer
with a type 140 (ICMPV6_NI_REPLY) packet.
Signed-off-by: NEric Leblond <eric@inl.fr>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is no point having the bss information of currently associated AP
when the AP is detected to be out of range.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This lets userspace request to get the currently set
regulatory domain.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Monitor mode is able to TX by using injected frames. We should
not allow injected frames to be sent unless allowed by regulatory
rules. Since AP mode uses a monitor interfaces to transmit
management frames we have to take care to not break AP mode as
well while resolving this. We can deal with this by allowing compliant
APs solutions to inform mac80211 if their monitor interface is
intended to be used for an AP by setting a cfg80211 flag for the
monitor interface. hostapd, for example, currently does its own
checks to ensure AP mode is not used on channels which require radar
detection. Once such solutions are available it can can add this
flag for monitor interfaces.
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Also call our own ieee80211_master_setup routine instead of
overwriting almost all the values from ether_setup; this
loses a few assignments that are pointless on the master
interface anyway.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Convert to new net_device_ops in 2.6.28 and later.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Giving the signal in dB isn't much more useful to userspace
than giving the signal in unspecified units. This removes
some radiotap information for zd1211 (the only driver using
this flag), but it helps a lot for getting cfg80211-based
scanning which won't support dB, and zd1211 being dB is a
little fishy anyway.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Cc: Bruno Randolf <bruno@thinktube.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The base versions handle constant folding now.
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

I hold back this patch for around a week to avoid
confusion. This is the second step of
"mac80211: Fixed BSSID handling revisited".

With it, in the situation of a strange merge to the
same BSSID (e.g. caused by a TSF overflow) only
reset_tsf() is called.

And sta_info_flush_delayed() is only called if you
change the network manually, not on an automatic
BSSID merge.
Signed-off-by: NAlina Friedrichsen <x-alina@gmx.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fixes a bug when creating a new IBSS network with a
fixed BSSID. The fixed BSSID situation is now with one of
my last patches handled in ieee80211_sta_find_ibss()
function.

It's more robust to test against
(ifsta->flags & IEEE80211_STA_PREV_BSSID_SET), because
ifsta->state is not seted right in every situation and so
the creating of the new IBSS network sometimes hangs after
the first try to scan for a network to merge.
Signed-off-by: NAlina Friedrichsen <x-alina@gmx.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Trying to associate with a non-existent SSID stops the
state machine after the first run. Subsequent association
requests fail to start the scan engine. Fix this by resetting
assoc_scan_tries to zero after completing a scan run.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

gro: Optimise TCP packet reception

As this function can be called more than half a million times for
10GbE, it's important to optimise it as much as we can.

This patch uses bit ops to logical ops, as well as open coding
memcmp to exploit alignment properties.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As this function can be called more than half a million times for
10GbE, it's important to optimise it as much as we can.

This patch does some obvious changes to use 2-byte and 4-byte
operations instead of byte-oriented ones where possible.  Bit
ops are also used to replace logical ops to reduce branching.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch optimises the Ethernet header comparison to use 2-byte
and 4-byte xors instead of memcmp.  In order to facilitate this,
the actual comparison is now carried out by the callers of the
shared dev_gro_receive function.

This has a significant impact when receiving 1500B packets through
10GbE.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch prepares for the move of the same_flow checks out of
dev_gro_receive.  As such we need to remember the number of held
packets since doing a loop just to count them every time is silly.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

$ diff-funcs xs_udp_write_space net/sunrpc/xprtsock.c
net/sunrpc/xprtsock.c xs_tcp_write_space
 --- net/sunrpc/xprtsock.c:xs_udp_write_space()
 +++ net/sunrpc/xprtsock.c:xs_tcp_write_space()
@@ -1,4 +1,4 @@
- * xs_udp_write_space - callback invoked when socket buffer space
+ * xs_tcp_write_space - callback invoked when socket buffer space
  *                             becomes available
  * @sk: socket whose state has changed
  *
@@ -7,12 +7,12 @@
  * progress, otherwise we'll waste resources thrashing kernel_sendmsg
  * with a bunch of small requests.
  */
-static void xs_udp_write_space(struct sock *sk)
+static void xs_tcp_write_space(struct sock *sk)
 {
 	read_lock(&sk->sk_callback_lock);

-	/* from net/core/sock.c:sock_def_write_space */
-	if (sock_writeable(sk)) {
+	/* from net/core/stream.c:sk_stream_write_space */
+	if (sk_stream_wspace(sk) >= sk_stream_min_wspace(sk)) {
 		struct socket *sock;
 		struct rpc_xprt *xprt;


$ codiff net/sunrpc/xprtsock.o net/sunrpc/xprtsock.o.new
net/sunrpc/xprtsock.c:
  xs_tcp_write_space | -163
  xs_udp_write_space | -163
 2 functions changed, 326 bytes removed

net/sunrpc/xprtsock.c:
  xs_write_space | +179
 1 function changed, 179 bytes added

net/sunrpc/xprtsock.o.new:
 3 functions changed, 179 bytes added, 326 bytes removed, diff: -147
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

$ codiff net/ipv6/addrconf.o net/ipv6/addrconf.o.new
net/ipv6/addrconf.c:
 addrconf_notify | -267
1 function changed, 267 bytes removed

net/ipv6/addrconf.c:
 add_addr |  +86
1 function changed, 86 bytes added

net/ipv6/addrconf.o.new:
2 functions changed, 86 bytes added, 267 bytes removed, diff: -181
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Acked-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the changes were done to the protocol last release, some endian
bugs crept in.  This patch fixes those endian problems and has been
verified to run on 32/64 bit and x86/ppc architectures.

This version of the patch incorporates the correct annotations
for endian variables.
Signed-off-by: NEric Van Hensbergen <ericvh@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>