Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 13 9月, 2007 1 次提交
  3. 12 9月, 2007 3 次提交
  5. 11 9月, 2007 1 次提交
  7. 31 8月, 2007 1 次提交
  9. 24 8月, 2007 1 次提交
    • L
      ACPI: Schedule /proc/acpi/event for removal · 14e04fb3
      由 Len Brown 提交于 
      Schedule /proc/acpi/event for removal in 6 months.

Re-name acpi_bus_generate_event() to acpi_bus_generate_proc_event()
to make sure there is no confusion that it is for /proc/acpi/event only.

Add CONFIG_ACPI_PROC_EVENT to allow removal of /proc/acpi/event.
There is no functional change if CONFIG_ACPI_PROC_EVENT=y
Signed-off-by: NLen Brown <len.brown@intel.com>
      14e04fb3
  11. 23 8月, 2007 6 次提交
  13. 21 8月, 2007 1 次提交
    • L
      ACPI: boot correctly with "nosmp" or "maxcpus=0" · 61ec7567
      由 Len Brown 提交于 
      In MPS mode, "nosmp" and "maxcpus=0" boot a UP kernel with IOAPIC disabled.
However, in ACPI mode, these parameters didn't completely disable
the IO APIC initialization code and boot failed.

init/main.c:
	Disable the IO_APIC if "nosmp" or "maxcpus=0"
	undefine disable_ioapic_setup() when it doesn't apply.

i386:
	delete ioapic_setup(), it was a duplicate of parse_noapic()
	delete undefinition of disable_ioapic_setup()

x86_64:
	rename disable_ioapic_setup() to parse_noapic() to match i386
	define disable_ioapic_setup() in header to match i386

http://bugzilla.kernel.org/show_bug.cgi?id=1641Acked-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLen Brown <len.brown@intel.com>
      61ec7567
  15. 20 8月, 2007 1 次提交
  17. 17 8月, 2007 1 次提交
  19. 15 8月, 2007 1 次提交
  21. 12 8月, 2007 12 次提交
    • L
      ACPI: thermal: create "thermal.act=" to disable or override active trip point · f8707ec9
      由 Len Brown 提交于 
      thermal.act=-1 disables all active trip points
in all ACPI thermal zones.

thermal.act=C, where C > 0, overrides all lowest temperature
active trip points in all thermal zones to C degrees Celsius.
Raising this trip-point may allow you to keep your system silent
up to a higher temperature.  However, it will not allow you to
raise the lowest temperature trip point above the next higher
trip point (if there is one).  Lowering this trip point may
kick in the fan sooner.

Note that overriding this trip-point will disable any BIOS attempts
to implement hysteresis around the lowest temperature trip point.
This may result in the fan starting and stopping frequently
if temperature frequently crosses C.

WARNING: raising trip points above the manufacturer's defaults
may cause the system to run at higher temperature and shorten
its life.
Signed-off-by: NLen Brown <len.brown@intel.com>
      f8707ec9
    • L
      ACPI: thermal: create "thermal.nocrt" to disable critical actions · f5487145
      由 Len Brown 提交于 
      thermal.nocrt=1 disables actions on _CRT and _HOT
ACPI thermal zone trip-points.  They will be marked
as <disabled> in /proc/acpi/thermal_zone/*/trip_points.

There are two cases where this option is used:

1. Debugging a hot system crossing valid trip point.

   If your system fan is spinning at full speed,
   be sure that the vent is not clogged with dust.
   Many laptops have very fine thermal fins that are easily blocked.

   Check that the processor fan-sink is properly seated,
   has the proper thermal grease, and is really spinning.

   Check for fan related options in BIOS SETUP.
   Sometimes there is a performance vs quiet option.
   Defaults are generally the most conservative.

   If your fan is not spinning, yet /proc/acpi/fan/
   has files in it, please file a Linux/ACPI bug.

   WARNING: you risk shortening the lifetime of your
   hardware if you use this parameter on a hot system.
   Note that this refers to all system components,
   including the disk drive.

2. Working around a cool system crossing critical
   trip point due to erroneous temperature reading.

   Try again with CONFIG_HWMON=n
   There is known potential for conflict between the
   the hwmon sub-system and the ACPI BIOS.
   If this fixes it, notify lm-sensors@lm-sensors.org
   and linux-acpi@vger.kernel.org

   Otherwise, file a Linux/ACPI bug, or notify
   just linux-acpi@vger.kernel.org.
Signed-off-by: NLen Brown <len.brown@intel.com>
      f5487145
    • L
      ACPI: thermal: create "thermal.psv=" to override passive trip points · a70cdc52
      由 Len Brown 提交于 
      "thermal.psv=-1" disables passive trip points
for all ACPI thermal zones.

"thermal.psv=C", where 'C' is degrees Celsius,
overrides all existing passive trip points
for all ACPI thermal zones.

thermal.psv is checked at module load time,
and in response to trip-point change events.

Note that if the system does not deliver thermal zone
temperature change events near the new trip-point,
then it will not be noticed.  To force your custom
trip point to be noticed, you may need to enable polling:
eg. thermal.tzp=3000 invokes polling every 5 minutes.

Note that once passive thermal throttling is invoked,
it has its own internal Thermal Sampling Period (_TSP),
that is unrelated to _TZP.

WARNING: disabling or raising a thermal trip point
may result in increased running temperature and
shorter hardware lifetime on some systems.
Signed-off-by: NLen Brown <len.brown@intel.com>
      a70cdc52
    • L
      ACPI: thermal: expose "thermal.tzp=" to set global polling frequency · 730ff34d
      由 Len Brown 提交于 
      Thermal Zone Polling frequency (_TZP) is an optional ACPI object
recommending the rate that the OS should poll the associated thermal zone.

If _TZP is 0, no polling should be used.
If _TZP is non-zero, then the platform recommends that
the OS poll the thermal zone at the specified rate.
The minimum period is 30 seconds.
The maximum period is 5 minutes.

(note _TZP and thermal.tzp units are in deci-seconds,
 so _TZP = 300 corresponds to 30 seconds)

If _TZP is not present, ACPI 3.0b recommends that the
thermal zone be polled at an "OS provided default frequency".

However, common industry practice is:
1. The BIOS never specifies any _TZP
2. High volume OS's from this century never poll any thermal zones

Ie. The OS depends on the platform's ability to
provoke thermal events when necessary, and
the "OS provided default frequency" is "never":-)

There is a proposal that ACPI 4.0 be updated to reflect
common industry practice -- ie. no _TZP, no polling.

The Linux kernel already follows this practice --
thermal zones are not polled unless _TZP is present and non-zero.

But thermal zone polling is useful as a workaround for systems
which have ACPI thermal control, but have an issue preventing
thermal events.  Indeed, some Linux distributions still
set a non-zero thermal polling frequency for this reason.

But rather than ask the user to write a polling frequency
into all the /proc/acpi/thermal_zone/*/polling_frequency
files, here we simply document and expose the already
existing module parameter to do the same at system level,
to simplify debugging those broken platforms.

Note that thermal.tzp is a module-load time parameter only.
Signed-off-by: NLen Brown <len.brown@intel.com>
      730ff34d
    • L
      ACPI: thermal: create "thermal.off=1" to disable ACPI thermal support · 72b33ef8
      由 Len Brown 提交于 
      "thermal.off=1" disables all ACPI thermal support at boot time.

CONFIG_ACPI_THERMAL=n can do this at build time.
"# rmmod thermal" can do this at run time,
as long as thermal is built as a module.

WARNING: On some systems, disabling ACPI thermal support
will cause the system to run hotter and reduce the
lifetime of the hardware.
Signed-off-by: NLen Brown <len.brown@intel.com>
      72b33ef8
    • H
      ACPI: thinkpad-acpi: fix sysfs paths in documentation · 9de1cc4a
      由 Henrique de Moraes Holschuh 提交于 
      The documentation used "thinkpad-acpi" to refer to the directories in
sysfs, while it should have been using "thinkpad_acpi".  Thanks to Hugh
Dickins for the error report.

I wish I could just call the module and everything else by the proper
name with the "-", instead of using these ugly translations to "_".
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: NLen Brown <len.brown@intel.com>
      9de1cc4a
    • A
      i386: Add warning in Documentation that zero-page is not a stable ABI · 43fb2387
      由 Andi Kleen 提交于 
      Some people writing boot loaders seem to falsely belief the 32bit zero page is a
stable interface for out of tree code like the real mode boot protocol. Add a comment
clarifying that is not true.
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      43fb2387
    • J
      docs: note about select in kconfig-language.txt · f8a74594
      由 Jarek Poplawski 提交于 
      A warning note from Sam Ravnborg about kconfig's select evilness,
dependencies and the future (slightly corrected).
Signed-off-by: NJarek Poplawski <jarkao2@o2.pl>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      f8a74594
    • J
      Documentation: sysrq, description of 'h' slightly inaccurate · 09736bd3
      由 Jesper Juhl 提交于 
      In Documentation/sysrq.txt, the description of 'h' says that any key not
listed *above* will generate help.  That's obviously not true since all the
keys listed below 'h' will do what they are described to do, not display help.
 So change the text so that it says that any key not listed in the table will
generate help, which is what really happens.
Signed-off-by: NJesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      09736bd3
    • G
      kernel-parameters.txt : watchdog.txt should be wdt.txt · 8dfe9c21
      由 Gabriel C 提交于 
      Documentation/watchdog/watchdog.txt does not exist, it is Documentation/watchdog/wdt.txt
Signed-off-by: NGabriel Craciunescu <nix.or.die@googlemail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      8dfe9c21
    • Y
      Memory hotplug document · 6867c931
      由 Yasunori Goto 提交于 
      This is add a document for memory hotplug to describe "How to use" and
"Current status".
Signed-off-by: NKAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: NYasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      6867c931
    • A
      pvr2fb: update Documentation/fb/pvr2fb.txt · acb73865
      由 Adrian McMenamin 提交于 
      The current version is very old and does not correctly specify how to
set the video mode.

Signed-off by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: NAntonino Daplas <adaplas@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      acb73865
  23. 10 8月, 2007 1 次提交
  25. 09 8月, 2007 4 次提交
  27. 03 8月, 2007 1 次提交
  29. 01 8月, 2007 5 次提交