These patches add generic dock event handling to acpiphp.  If there are
pci devices that need to be inserted/removed after the dock event, the
event notification will be handed down to the normal pci hotplug event
handler in acpiphp so that new bridges/devices can be enumerated.

Because some dock stations do not have pci bridges or pci devices that
need to be inserted after a dock, acpiphp will remain loaded to handle
dock events even if no hotpluggable pci slots are discovered.

You probably need to have the pci=assign-busses kernel parameter enabled
to use these patches, and you may not allow ibm_acpi to handle docking
notifications and use this patch.

This patch incorporates feedback provided by many.
Signed-off-by: NKristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

If we add a new bridge with subordinate busses, we should call make sure
that acpi is notified so that the PRT (if present) can be read and drivers
who have registered on this bus will be notified when it is started.
Also make sure to use the max reserved bus number for the starting the bus
scan.
Signed-off-by: NKristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

semaphore to mutex conversion.

the conversion was generated via scripts, and the result was validated
automatically via a script as well.

build tested with allyesconfig.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Only size the bus that has been added.
Signed-off-by: NKristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Allocate resources for adapters with bridges on them.
Signed-off-by: NKristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds PCI based I/O xAPIC hot-add support to ACPIPHP
driver. When PCI root bridge is hot-added, all PCI based I/O xAPICs
under the root bridge are hot-added by this patch. Hot-remove support
is TBD.
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Current acpiphp code does not distinguish between the physical presence and
power state of a device/slot.  That is, if a device has to be disabled, it
also tries to physically ejects the device.  This patch decouples power state
from physical presence.  You can now echo to the corresponding sysfs power
control file to repeatedly enable and disable a device without having to
physically re-insert it.
Signed-off-by: NRajesh Shah <rajesh.shah@intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

acpiphp changes to support acpi based root bridge hot-add.
Signed-off-by: NRajesh Shah <rajesh.shah@intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Earlier I reported that Matthew's acpiphp rewrite had problem in powering down
slot on my i386 system.  The following patch is needed to get the acpiphp
rewrite properly powering down the slot.
Signed-off-by: NDely Sy <dely.l.sy@intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

A root bridge may not have directly attached hotpluggable slots under it.
Instead, it may have p2p bridges with slots under it.  In this case, we need
to clean up the p2p bridges and slots properly too.  Patch below applies on
top of the original patch, and fixes this problem.  Without this, acpiphp
leaves behind notify handlers on module unload, and subsequent module load
attempts don't work properly too.  Patch was tested on an ia64 Tiger4 box.
Signed-off-by: NRajesh Shah <rajesh.shah@intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch converts acpiphp to use the generic PCI resource assignment code.
It's quite large, but most of it is deleting the acpiphp_pci and acpiphp_res
files.  It's tested on an hp Integrity rx8620 (which won't work without this
patch).  Testers with other hardware welcomed.
Signed-off-by: NMatthew Wilcox <matthew@wil.cx>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!