For forwarding using ACL action, HW needs a valid FID to be setup. It
does not actually use it, so it can be any valid FID. So create a dummy
FID only for this purpose.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement part of multipurpose Virtual Router and Forwarding Domain
Action that takes care of setting up FID. We need to use it to be able
to forward packets using ACL action when no FID is associated on RX.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Trivial conversion as only one vector is supported, but at least we
lose the useless msix_entry member in the per-device structure.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Tested-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement dpipe's table ops for erif table which provide:
1. Getting the entries in the table with the associate values.
	- match on "mlxsw_meta:erif_index"
	- action on "mlxsw_meta:forwared_out"
2. Synchronize the hardware in case of enabling/disabling counters which
   mean removing erif counters from all interfaces.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add rif helper function to access the rif index and rif devices ifindex.
This functions will be used by dpipe in order to dump the rif table.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for counter allocation on router interfaces. The allocation
depends on the counter state of relevant table. In case the counting is
disabled or no counters left the counter index will be set as invalid.

Also a counter pool for router allocation is added.
Signed-off-by: NArakdi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The RICNT register retrieves per port performance counter. It will be
used to query the router interfaces statistics.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add definition for egress router interface table. This table describes
the final part in the routing pipeline. This table matches the egress
interface index (rif index, which is set by the previous stages and
determine the out port) and makes the decision of forwarding the packet
towards the L2 logic or dropping it.

The metadata header is added to represent this internal information.
The rif index field is mapped logically to netdevice ifindex.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add placeholder for dpipe. Support for specific tables and headers will
be introduced in following patches. The headers are shared between all
mlxsw_sp instances.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update RITR for counter support. This allows adding counters for
ASIC's router ports.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the return allocated index and err value are multiplexed.
This patch changes the API to decouple the ret value from the allocated
index.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As explained in the previous patch, the cell size may change in future
devices, so query it from the firmware instead of hard coding it.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The sizes and thresholds of the priority group (PG) buffers are
configured in cells, which represent a specific amount of bytes.

The cell size can vary in different devices, so it's better to query it
from the firmware than hard coding it.

Refactor the code dealing with this value into different functions, so
that it will be easier to make the conversion in the next patch.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of hard coding the size of the shared buffer in the driver,
query it from the firmware, as it may change in future devices.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We currently hard code the maximum number of ports in the driver, but
this may change in future devices, so query it from the firmware
instead.

Fallback to a maximum of 64 ports in case this number can't be queried.
This should only happen in SwitchX-2 for which this number is correct.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of hard coding the number of LPM trees in the driver, query it
from the firmware, as it may change in future devices.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We don't use it during development and we can't extend it either, so
remove it.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The arguments packets and bytes to call mlxsw_sp_acl_rule_get_stats are
in the wrong order. Fix this by swapping them.

Detected by CoverityScan, CID#1419705 ("Arguments in wrong order")

Fixes: 7c1b8eb1 ("mlxsw: spectrum: Add support for TC flower offload statistics")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Acked-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Align the default case for matchall offload with what's there
for flower.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Acked-by: NYotam Gigi <yotamg@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the struct representing router interface "mlxsw_sp_rif"
is reffered as "r" in various places in the driver. Furthermore it
contains a member which specify the index which is called "rif".
This patch change "r" to "rif" and "rif" to "rif_index".
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that port netdevs can be enslaved to a VRF master we need to make
sure the device's routing tables won't be flushed upon the insertion of
a l3mdev rule.

Note that we assume the notified l3mdev rule is a simple rule as used by
the VRF master. We don't check for the presence of other selectors such
as 'iif' and 'oif'.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In a similar fashion to the previous patch, allow bridges and VLAN
devices on top of bridges to be enslaved to a VRF master device.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow port netdevs, LAG and VLAN devices stacked on top of these to be
enslaved to a VRF master device.

Upon enslavement, create a router interface (RIF) for the enslaved
netdev and associate it with a virtual router (VR) based on the VRF's
table ID.

If a RIF already exists for the netdev (f.e., due to the existence of an
IP address), then it's deleted and a new one is created with the
appropriate VR binding.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We usually destroy the netdev's router interface (RIF) when the last IP
address is removed from it.

However, we shouldn't do that if it's enslaved to an L3 master device.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a router interface (RIF) is created due to a netdev being enslaved
to a VRF master, then it should be associated with the appropriate
virtual router (VR) and not the default one.

If netdev is a VRF slave, lookup the VR based on the VRF's table ID.
Otherwise default to the MAIN table.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In commit c3852ef7 ("ipv4: fib: Replay events when registering FIB
notifier") we dumped the FIB tables and replayed the events to the
passed notification block.

However, we merely sent a RULE_ADD notification in case custom rules
were in use. As explained in previous patches, this approach won't work
anymore. Instead, we should notify the caller about all the FIB rules
and let it act accordingly.

Upon registration to the FIB notification chain, replay a RULE_ADD
notification for each programmed FIB rule, custom or not. The integrity
of the dump is ensured by the mechanism introduced in the above
mentioned commit.

Prevent regressions by making sure current listeners correctly sanitize
the notified rules.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Acked-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The num_rec field is 8 bit, so the maximal count number is 255.
This fixes vlans learning not being enabled for wider ranges than 255.

Fixes: a4feea74 ("mlxsw: reg: Add Switch Port VLAN MAC Learning register definition")
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The num_rec field is 8 bit, so the maximal count number is 255. This
fixes vlans not being enabled for wider ranges than 255.

Fixes: b2e345f9 ("mlxsw: reg: Add Switch Port VID and Switch Port VLAN Membership registers definitions")
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for TC flower offload statistics including number of packets,
bytes and last use timestamp. Currently the statistics are gathered on a
per-rule basis.
Signed-off-by: NArkadi Sharshvesky <arkadis@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for packets and byte statistics on TCAM entries. The counters
are allocated from the generic flow counters pool.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for Policing and Counting action block. This action block
will be used to bind counter to TCAM entries.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce periodic task for dumping the activity status for the ACL
rule TCAM entries. This is done in order to emulate last use statistics.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.comi>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the ACL rules can be accessed only by hashing. In order to
dump the activity the rules are also placed in a list.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for retrieving TCAM entry activity. In order to support ACL
rule activity corresponding TCAM entry should be queried.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for allocating generic flow counter. Generic flow counter
can count packets or packets and bytes and can be assigned to different
hardware processes. First use will be for counting packets and bytes of
ACL rules, and will be introduced in the following patches.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: NIdo schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MGPC register retrieves generic flow counter value. It will be
used to query ACL counters.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add implementation for counter allocator. The ASIC has special memory
pool for various counting purposes. Counter memory is distributed between
equal size banks.

The static sub-pool configuration should specify the following parameters
for each sub-pool:
- Number of required banks.
- Maximum entry size.

Each module can add dedicated sub-pool or use existing one.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the abort mechanism is invoked it binds the first virtual router
(VR) to an LPM tree and inserts a default route to direct packets to the
CPU.

With VRFs, we can have router interfaces (RIFs) bound to multiple VRs,
so we need to make sure packets are trapped from all VRs and not just
the first one.

Upon abort invocation, bind all active VRs to the same LPM tree and
insert a default route in each.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Up until now we implicitly associated all the router interfaces (RIFs)
with the first virtual router (VR). This must be changed in order to
enable VRF offload. Otherwise, a packet received via a VRF slave would
do a FIB lookup in the same table used by other VRFs.

Instead, bind the RIF to a VR according to the table where FIB lookup
should be performed for packets received via the RIF.

Currently, we only care about the MAIN and LOCAL tables (which we squash
together).
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>