_mmc_detect_card_removed() validates that the card is removable, but when
being called via the bus_ops ->detect() callbacks, the validation is
redundant as it's already done in mmc_rescan().

Move the validation of a removable card to the mmc_detect_card_removed()
API, which is where it's applicable, to allow the blk error recovery path
to get the response a bit earlier.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Instead of checking for "#ifdef" directly in the code, let's invent a pair
of mmc core functions to deal with register/unregister the MMC PM notifier
block. Implement stubs for these functions when CONFIG_PM_SLEEP is unset,
as in that case the PM notifiers isn't used.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

MMC_CAP_RUNTIME_RESUME was invented to decrease system PM resume time for
systems that particularly needs this. As the feature has matured let's
make it the default behavior for MMC/SD.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

As mmc_claim_host() invokes pm_runtime_get_sync() for the mmc host device,
it's important that the host is kept claimed for *all* accesses to it via
the host_ops callbacks.

In mmc_rescan(), the ->card_event() and the ->get_cd() callback are being
invoked without claiming the host, let's fix this.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The ->card_event() callback may be called when re-scan is disabled and for
non-removable cards, which both cases are unnecessary.

Instead let's move the call later in mmc_rescan() where these constraints
have been validated.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Though the mmc core driver should/will continue to support the legacy
"enable-sdio-wakeup" property to enable SDIO as the wakeup source, we
need to add support for the new standard property "wakeup-source".

This patch adds support for "wakeup-source" property in addition to the
existing "enable-sdio-wakeup" property.

Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NSudeep Holla <sudeep.holla@arm.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

mmc_select_hs400() calls __mmc_switch() which checks the switch is
successful using CMD13 (SEND_STATUS).  The problem is that it does that
using the timing settings of the previous mode.  That is prone to error,
especially when switching from HS to HS400 because the timing parameters
for HS mode are tighter than the timing parameters for HS400 mode.

In the case when CMD13 polling is used (i.e. not MMC_CAP_WAIT_WHILE_BUSY)
with the switch command, it must be assumed that using different modes on
the card and host must work.

However in the case when CMD13 polling is not used
(i.e. MMC_CAP_WAIT_WHILE_BUSY) mmc_select_hs400() can be made more
reliable by setting the host to the correct timing before sending CMD13.

This patch does that.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org> # 4.2+
Tested-by: NAlim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Move the mmc_switch_status() function in preparation for calling it
in mmc_select_hs400().
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org> # 4.2+
Tested-by: NAlim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

mmc_select_hs400() begins with the card and host in HS200 mode.
Therefore, any commands sent to the card should use HS200 timing.
It is incorrect to set the host to High Speed (HS) timing before
sending the switch command.  Doing so is unreliable because
the timing parameters for HS mode are tighter than the timing
parameters for HS200 mode.  Thus the HS timings should be set
only after the card has switched mode.

However, it is not unreasonable first to reduce the frequency to
the HS mode frequency, which should make the switch command and
subsequent CMD13 commands more reliable.

This patch does that.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org> # 4.2+
Tested-by: NAlim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Currently mmc_select_hs200() uses __mmc_switch() which checks the
success of the switch to HS200 mode using CMD13 (SEND_STATUS).
The problem is that it does that using the timing settings of legacy
mode.  That is prone to error, not least because the timing parameters
for legacy mode are tighter than the timing parameters for HS200 mode.

In the case when CMD13 polling is used (i.e. not MMC_CAP_WAIT_WHILE_BUSY)
with the switch command, it must be assumed that using different modes on
the card and host must work.

However in the case when CMD13 polling is not used
(i.e. MMC_CAP_WAIT_WHILE_BUSY) mmc_select_hs200() can be made more
reliable by setting the host to the correct timing before sending CMD13.

This patch does that.

A complication is that the caller, mmc_select_timing(), will ignore a
switch error (indicated by -EBADMSG), assume the old mode is valid
and continue, so the old timing must be restored in that case.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org> # 4.2+
Tested-by: NAlim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The pwrseq_emmc driver does a eMMC card reset before a system reboot to
allow broken or limited ROM boot-loaders (that don't have an eMMC reset
logic) to be able to read the second stage from the eMMC.

But this has to be called before a system reboot handler and while most
of them use the priority 128, there are other restart handlers (such as
the syscon-reboot one) that use a higher priority. So, use the highest
priority to make sure that the eMMC hw is reset before a system reboot.
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Tested-by: NMarkus Reichl <m.reichl@fivetechno.de>
Tested-by: NAnand Moon <linux.amoon@gmail.com>
Reviewed-by: NAlim Akhtar <alim.akhtar@samsung.com>
Tested-by: NDouglas Anderson <dianders@chromium.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The mmc_execute_tuning() has already prepared the opcode,
there is no need to prepare it again at mmc_send_tuning(),
and, there is a BUG of mmc_send_tuning() to determine the opcode
by bus width, assume eMMC was running at HS200, 4bit mode,
then the mmc_send_tuning() will overwrite the opcode from CMD21
to CMD19, then got error.

in addition, extend an argument of "cmd_error" to allow getting
if there was cmd error when tune response.
Signed-off-by: NChaotian Jing <chaotian.jing@mediatek.com>
[Ulf: Rebased patch]
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Sometime only need set MMC_CAP_HW_RESET for one of MMC hosts,
So set it in device tree is better.
Signed-off-by: NChaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

There's little sense in releasing the host on mmc_add_card() error
immediately after reclaiming  it, so reclaim the host  only in case
of success.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This adds logic to the MMC core to set VQMMC.  This is expected to be
called by MMC drivers like dw_mmc as part of (or instead of) their
start_signal_voltage_switch() callback.

A few notes:

* When setting the signal voltage to 3.3V we do our best to make VQMMC
  and VMMC match.  It's been reported that this makes some old cards
  happy since they were tested back in the day before UHS when VQMMC
  and VMMC were provided by the same regulator.  A nice side effect of
  this is that we don't end up on the hairy edge of VQMMC (2.7V),
  which some EEs claim is a little too close to the minimum for
  comfort.
  This is done in two steps. At first we try to find a VQMMC within
  a 0.3V tolerance of VMMC and if this is not supported by the
  supplying regulator we try to find a suitable voltage within the
  whole 2.7V-3.6V area of the spec.

* The two step approach is currently necessary, as the used
  regulator_set_voltage_triplet(min, target, max) uses a simple
  implementation that just tries two basic steps:
	regulator_set_voltage(target, max);
	regulator_set_voltage(min, target);
  So with only one step with 2.7-3.6V borders, if a suitable voltage
  is a bit below VMMC, we would directly get the lowest 2.7V
  which some boards (like Rockchips) don't like at all.

* When setting the signal voltage to 1.8V or 1.2V we aim for that
  specific voltage instead of picking the lowest one in the range.

* We very purposely don't print errors in mmc_regulator_set_vqmmc().
  There are cases where the MMC core will try several different
  voltages and we don't want to pollute the logs.
Signed-off-by: NDouglas Anderson <dianders@chromium.org>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

We will shortly need the calculation of an ocr-bit to the actual
voltage in a second place too, so move it from mmc_regulator_set_ocr
to a common function mmc_ocrbitnum_to_vdd to make that possible.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

MMC_CLKGATE was once invented to save power by gating the bus clock at
request inactivity. At that time it served its purpose. The modern way to
deal with power saving for these scenarios, is by using runtime PM.

Nowadays, several host drivers have deployed runtime PM, but for those
that haven't and which still cares power saving at request inactivity,
it's certainly time to deploy runtime PM as it has been around for several
years now.

To simplify code to mmc core and thus decrease maintenance efforts, this
patch removes all code related to MMC_CLKGATE.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>

As SD Specifications Part1 Physical Layer Specification Version
3.01 says, CMD19 tuning is available for unlocked cards in transfer
state of 1.8V signaling mode. The small difference between v3.00
and 3.01 spec means that CMD19 tuning is also available for DDR50
mode.
Signed-off-by: NWeijun Yang <york.yang@csr.com>
Signed-off-by: NBarry Song <Baohua.Song@csr.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch add MMC_TIMING_UHS_SDR12 and MMC_TIMING_UHS_SDR25
for mmc_ios_show to show the ios->timing if mmc card runs under
these two modes.
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Some sdio wifi chips will not work properly if we try to start new
sdio-rw requests while the device is signalling that it is busy.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add a helper function to check if an opcode is a sd-io-rw-* opcode.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The simple power sequence provider sets a value for multiple GPIOs in one
go so it is better to use the API already provided by the GPIO descriptor
API instead of open coding the same logic.
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch add ios->drv_type for mmc_ios_show to show the
card's driver type.
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The gpiod_get() function expands to gpiod_get_index() with index 0
so it's better to use it since is easier to read and more concise.
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

As there are no users of the __mmc_switch() API, except for the mmc core
itself, let's convert it from an exported function into an internal.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Signed-off-by: NYousong Zhou <yszhou4tech@gmail.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

As mmc_claim_host() invokes pm_runtime_get_sync() for the mmc host device,
it's important that the host is kept claimed for *all* accesses to it via
the host_ops callbacks.

In some code paths for SDIO, particularly related to the PM support,
mmc_power_off|up() is invoked without keeping the host claimed. Let's fix
these.

Moreover, mmc_start|stop_host() also invokes mmc_power_off|up() without
claiming the host, let's fix these as well.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NKishon Vijay Abraham I <kishon@ti.com>

Suppose that we got a data crc error, and it triggers the mmc_reset.
mmc_reset will call mmc_send_status to see if HW reset was supported.
before issue CMD13, it will do retune, and if EMMC was in HS400 mode,
it will reduce frequency to 52Mhz firstly, then results in card init
was doing at 52Mhz.
The mmc_send_status was originally only done for mmc_test, should drop
it. And, rename the "eMMC hardware reset" to "Reset test", as we would
also be able to use the test for SD-cards.
Signed-off-by: NChaotian Jing <chaotian.jing@mediatek.com>
Suggested-by: NAdrian Hunter <adrian.hunter@intel.com>
Fixes: bd11e8bd ("mmc: core: Flag re-tuning is needed on CRC errors")
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

When get a CRC error, start the mmc_retune, it will issue CMD19/CMD21
to do tune, assume there were 10 clock phase need to try, phase 0 to
phase 6 is ok, phase 7 to phase 9 is NG, we try it from 0 to 9, so
the last CMD19/CMD21 will get CRC error, host->need_retune was set and
cause mmc_retune was called, then dead loop of mmc_retune
Signed-off-by: NChaotian Jing <chaotian.jing@mediatek.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Fixes: bd11e8bd ("mmc: core: Flag re-tuning is needed on CRC errors")
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

When CONFIG_GPIOLIB is unset, its stubs will return -ENOSYS. That means
when the mmc core parses DT for CD/WP GPIOs via mmc_of_parse(), -ENOSYS
becomes propagated to the caller. Typically this means that the mmc host
driver fails to probe.

As the CD/WP GPIOs are already treated as optional, let's extend that to
cover the case when CONFIG_GPIOLIB is unset.
Reported-by: NMichal Simek <michal.simek@xilinx.com>
Fixes: 16b23787 ("mmc: sdhci-of-arasan: Call OF parsing for MMC")
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NMichal Simek <michal.simek@xilinx.com>
Acked-by: NVenu Byravarasu <vbyravarasu@nvidia.com>

The following panic is captured in ker3.14, but the issue still exists
in latest kernel.
---------------------------------------------------------------------
[   20.738217] c0 3136 (Compiler) Unable to handle kernel NULL pointer dereference
at virtual address 00000578
......
[   20.738499] c0 3136 (Compiler) PC is at _raw_spin_lock_irqsave+0x24/0x60
[   20.738527] c0 3136 (Compiler) LR is at _raw_spin_lock_irqsave+0x20/0x60
[   20.740134] c0 3136 (Compiler) Call trace:
[   20.740165] c0 3136 (Compiler) [<ffffffc0008ee900>] _raw_spin_lock_irqsave+0x24/0x60
[   20.740200] c0 3136 (Compiler) [<ffffffc0000dd024>] __wake_up+0x1c/0x54
[   20.740230] c0 3136 (Compiler) [<ffffffc000639414>] mmc_wait_data_done+0x28/0x34
[   20.740262] c0 3136 (Compiler) [<ffffffc0006391a0>] mmc_request_done+0xa4/0x220
[   20.740314] c0 3136 (Compiler) [<ffffffc000656894>] sdhci_tasklet_finish+0xac/0x264
[   20.740352] c0 3136 (Compiler) [<ffffffc0000a2b58>] tasklet_action+0xa0/0x158
[   20.740382] c0 3136 (Compiler) [<ffffffc0000a2078>] __do_softirq+0x10c/0x2e4
[   20.740411] c0 3136 (Compiler) [<ffffffc0000a24bc>] irq_exit+0x8c/0xc0
[   20.740439] c0 3136 (Compiler) [<ffffffc00008489c>] handle_IRQ+0x48/0xac
[   20.740469] c0 3136 (Compiler) [<ffffffc000081428>] gic_handle_irq+0x38/0x7c
----------------------------------------------------------------------
Because in SMP, "mrq" has race condition between below two paths:
path1: CPU0: <tasklet context>
  static void mmc_wait_data_done(struct mmc_request *mrq)
  {
     mrq->host->context_info.is_done_rcv = true;
     //
     // If CPU0 has just finished "is_done_rcv = true" in path1, and at
     // this moment, IRQ or ICache line missing happens in CPU0.
     // What happens in CPU1 (path2)?
     //
     // If the mmcqd thread in CPU1(path2) hasn't entered to sleep mode:
     // path2 would have chance to break from wait_event_interruptible
     // in mmc_wait_for_data_req_done and continue to run for next
     // mmc_request (mmc_blk_rw_rq_prep).
     //
     // Within mmc_blk_rq_prep, mrq is cleared to 0.
     // If below line still gets host from "mrq" as the result of
     // compiler, the panic happens as we traced.
     wake_up_interruptible(&mrq->host->context_info.wait);
  }

path2: CPU1: <The mmcqd thread runs mmc_queue_thread>
  static int mmc_wait_for_data_req_done(...
  {
     ...
     while (1) {
           wait_event_interruptible(context_info->wait,
                   (context_info->is_done_rcv ||
                    context_info->is_new_req));
     	   static void mmc_blk_rw_rq_prep(...
           {
           ...
           memset(brq, 0, sizeof(struct mmc_blk_request));

This issue happens very coincidentally; however adding mdelay(1) in
mmc_wait_data_done as below could duplicate it easily.

   static void mmc_wait_data_done(struct mmc_request *mrq)
   {
     mrq->host->context_info.is_done_rcv = true;
+    mdelay(1);
     wake_up_interruptible(&mrq->host->context_info.wait);
    }

At runtime, IRQ or ICache line missing may just happen at the same place
of the mdelay(1).

This patch gets the mmc_context_info at the beginning of function, it can
avoid this race condition.
Signed-off-by: NJialing Fu <jlfu@marvell.com>
Tested-by: NShawn Lin <shawn.lin@rock-chips.com>
Fixes: 2220eedf ("mmc: fix async request mechanism ....")
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

For some mass production of kingston eMMCs which adopt Phison's
firmware will meet an unrecoverable data conrruption occasionally
if performing trim due to a firmware bug confirmed by vendor. We
found it on Intel-C3230RK platform. So we add fixup of broken trim
for it.
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Use more compact of_property_read_bool() calls instead of the
of_find_property() calls.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

When requesting a trim for several bytes, everything up to the next
erase-group is erased. This causes data corruption.
Signed-off-by: NRobin van der Gracht <robin@protonic.nl>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

In the (not so unlikely) case that the mmc controller timeout budget is
enough for exactly one erase-group, the simplification of allowing one
sector has an enormous performance penalty. We optimize this special case
by introducing a flag that prohibits erase-group boundary crossing, so
that we can allow trimming more than one sector at a time.
Signed-off-by: NDavid Jander <david@protonic.nl>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Other subsystem buses attach PM domains during probe, but prior calling
the driver's ->probe() method. During the removal phase, detaching the PM
domain will be done after invoking the driver's ->remove() callback.

Convert the SDIO bus to follow this behavior and add error handling.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Since the ->reset() callback is implemented for SD, the ->power_restore()
callback has become redundant, let's remove it.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Since the ->reset() callback is implemented for MMC, the ->power_restore()
callback has become redundant, let's remove it.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add the ability to set eMMC driver strength
for HS200 and HS400.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

In preparation for supporing drive strength selection
for eMMC, read the card's valid driver strengths.

Note that though the SD spec uses the term "drive strength",
the JEDEC eMMC spec uses the term "driver strength".
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>