These supplies going to be needed for the twl6040 driver.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add platform device registratation for HDMI audio codec. This is to
be able to transmit audio through the HDMI output featured in SDP4430
and Blaze boards.
Signed-off-by: NRicardo Neri <ricardo.neri@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Complete the separation of the twl6040 from the twl core since
it is a separate chip, not part of the twl6030 PMIC.

Make the needed Kconfig changes for the depending drivers at the
same time to avoid breaking the kernel build (vibra, ASoC components).
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: NMark Brown <broonie@opensource.wolfsonicro.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Acked-by: NDmitry Torokhov <dtor@mail.ru>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The following commits change gpio-omap to use dynamic
IRQ allocation:

25db711d gpio/omap: Fix IRQ handling for SPARSE_IRQ
384ebe1c gpio/omap: Add DT support to GPIO driver

With dynamic allocation of IRQ the usage of OMAP_GPIO_IRQ
is no longer valid. We must be using gpio_to_irq() instead.
Signed-off-by: NTarun Kanti DebBarma <tarun.kanti@ti.com>
[tony@atomide.com: updated comments]
Signed-off-by: NTony Lindgren <tony@atomide.com>

With the introduction of dynamically allocated IRQ in the twl6030 driver,
the board files can no longer rely of static IRQ defines like before.

Retrieve the value dynamically allocated from the mmc -> twl6030 init
callback.

Note: The Panda board does not seems to use the card detect IRQ.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This patch allows us to drop the OMAP dependency from the OMAP4 keypad
driver.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

sdp4430_spi_board_info.irq was initialized to ETH_KS8851_IRQ and in
omap_4430sdp_init() overwritten with gpio_to_irq(ETH_KS8851_IRQ) before
sdp4430_spi_board_info was registered. This is a bit confusing, so
better don't initialize .irq and document that it is set later.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Otherwise omap_device_build() and omap_mux related functions
can't be marked as __init when twl is build as a module.

If a board is using GPIO pins or regulators configured by an
external chip, such as TWL PMIC on I2C bus, the board must
mark those MMC controllers as deferred. Additionally both
omap_hsmmc_init() and omap_hsmmc_late_init() must be called
by the board.

For MMC controllers using internal GPIO pins for card
detect and regulators the slots don't need to be marked
deferred. In this case calling omap_hsmmc_init() is sufficient.

Only mark the MMC slots using gpio_cd or gpio_wd as deferred
as noted by Igor Grinberg <grinberg@compulab.co.il>.

Note that this patch does not change the behaviour for
board-4430sdp.c board-omap4panda.c. These boards wrongly
rely on the omap_hsmmc.c init function callback to configure
the PMIC GPIO interrupt lines on external chip. If the PMIC
interrupt lines are not configured during init, they will
fail.
Reported-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

It's useful to print the error code when a called function fails so a
diagnosis of why it failed is possible.  In this case, it fails because
we try to register some data for the wl12xx driver, but as the driver
is not configured, a stub function is used which simply returns -ENOSYS.

Let's do the simple thing for -rc and print the error code.

Also, the return code from platform_register_device() at each of these
sites was not being checked.  Add some checking, and again print the
error code.

This should be fixed properly for the next merge window so we don't
issue error messages merely because a driver is not configured.
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

WARNING: arch/arm/mach-omap2/built-in.o(.text+0xb798): Section mismatch in reference from the function omap_4430sdp_display_init() to the function .init.text:omap_display_init()
The function omap_4430sdp_display_init() references
the function __init omap_display_init().
This is often because omap_4430sdp_display_init lacks a __init
annotation or the annotation of omap_display_init is wrong.

Fix this by adding __init to omap_4430sdp_display_init().
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Found by review.

omap4_sdp4430_wifi_mux_init() is called by an __init marked function,
and only calls omap_mux_init_gpio() and omap_mux_init_signal() which
are both also an __init marked functions.

The only reason this doesn't issue a warning is because the compiler
inlines omap4_sdp4430_wifi_mux_init() into omap4_sdp4430_wifi_init().

So, lets add the __init annotation to ensure this remains safe should
the compiler choose not to inline.
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

To avoid breakage in audio support with the coming change
in ASoC machine driver (conversion to platfrom device).
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
CC: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>

A hardware bug in the OMAP4 HDMI PHY causes physical damage to the board
if the HDMI PHY is kept powered on when the cable is not connected.

This patch solves the problem by adding hot-plug-detection into the HDMI
IP driver. This is not a real HPD support in the sense that nobody else
than the IP driver gets to know about the HPD events, but is only meant
to fix the HW bug.

The strategy is simple: If the display device is turned off by the user,
the PHY power is set to OFF. When the display device is turned on by the
user, the PHY power is set either to LDOON or TXON, depending on whether
the HDMI cable is connected.

The reason to avoid PHY OFF when the display device is on, but the cable
is disconnected, is that when the PHY is turned OFF, the HDMI IP is not
"ticking" and thus the DISPC does not receive pixel clock from the HDMI
IP. This would, for example, prevent any VSYNCs from happening, and
would thus affect the users of omapdss. By using LDOON when the cable is
disconnected we'll avoid the HW bug, but keep the HDMI working as usual
from the user's point of view.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Both Panda and 4430SDP use GPIO 63 as HDMI hot-plug-detect. Configure
this GPIO in the board files.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

The HDMI GPIO pins LS_OE and CT_CP_HPD are not currently configured.
This patch configures them as output pins.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

The GPIO 60 on 4430sdp and Panda is not HPD GPIO, as currently marked in
the board files, but CT_CP_HPD, which is used to enable/disable HPD
functionality.

This patch renames the GPIO.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

Instead of freeing the GPIOs individually, use gpio_free_array().
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

Hook these platforms restart code into the new restart hook rather
than using arch_reset().
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Disables the internal pull resistor for SDA and SCL which are enabled by
default, as there are external pull up's in 4460 and 4430 ES2.3
SDP, Blaze and Panda Boards, It is done to avoid the EDID read failure.
Signed-off-by: NRicardo Salveti de Araujo <ricardo.salveti@linaro.org>
Signed-off-by: NMythri P K <mythripk@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Move duplicate HDMI mux_init code from omap4 and panda board file
to display file.
Signed-off-by: NMythri P K <mythripk@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Padconf wakeup is used to wakeup uart after uart fclks/iclks are gated.
Rx-Pad wakeup was done by writing to rx-pad offset value populated in
serial.c idle_init. Remove the direct reading and writing into rx pad.
Remove the padconf field part of omap_uart_state struct and pad offsets
populated.

Now with mux framework support we can use mux_utilities
along with hmwod framework to handle io-pad configuration and enable rx-pad
wake-up mechanism.

To avoid breaking any board support add default mux data for all uart's
if mux info is not passed from board file.
With the default pads populated in serial.c wakeup capability for
rx pads is set, this can be used to enable uart_rx io-pad wakeup from
hwmod framework. The pad values in 3430sdp/4430sdp/omap4panda board file
are same as the default pad values populated in serial.c. Remove pad values
from 3430sdp/4430sdp/omap4panda board file and use the default pads
from serial.c file.
Signed-off-by: NGovindraj.R <govindraj.raja@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

OMAP4 SDP/Blaze boards have onboard digital microphones.
Register the platform device for the dmic-codec to be
able to use the microphones.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Declare support for keeping the power of the wlan chip
while suspended. this is needed for Wakeup-On-Wireless.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

As suggested by Russell King - ARM Linux <linux@arm.linux.org.uk>,
there's no need to keep local prototypes in non-local headers.

Add mach-omap1/common.h and mach-omap2/common.h and move the
local prototypes there from plat/common.h and mach/omap4-common.h.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Convert the omap2plus platforms to be using CONFIG_MULTI_IRQ_HANDLER.
Each machine is modified to provide either omap2_intc_handle_irq(),
omap3_intc_handle_irq() or gic_handle_irq().

This allows for a major cleanup, removing the MULTI_OMAP setup
from the interrupt path.

Tested on both Panda and IGEPv2 (single kernel image)
Tested-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

`keypad_pads' is referred to by `keypad_data' which is
not __initdata, so `keypad_pads' should not be __initdata either.
Signed-off-by: NBjarne Steinsbo <bsteinsbo@gmail.com>
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

An on-board projector named picodlp is available for OMAP4430 SDP.

Entry for this picodlp as a panel is being added in dss_devices array to
the board file.  It needs 4 GPIO pins for interfacing with host
processor and these are defined and two of them are configured in board
file.  Two GPIOs power_on and display_select are configured here.
picodlp also needs an i2c client over i2c controller-2 at address 0x1b.
Signed-off-by: NMayuresh Janorkar <mayur@ti.com>
Signed-off-by: NMythri P K <mythripk@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

4430SDP has two Taal DSI panels, connected to DSI 1 and DSI 2 modules.
The panels use a common PWM backlight, which will be implemented later
when the PWM driver has been improved to support the backlight.

Until the PWM driver has been improved, the following hack added to
arch/arm/mach-omap2/board-4430sdp.c can be used to set the backlight to
max:

static int omap_4430sdp_hack_backlight(void)
{
       twl_i2c_write_u8(TWL_MODULE_PWM, 0x7f, LED_PWM2OFF);
       twl_i2c_write_u8(TWL_MODULE_PWM, 0x7f, LED_PWM2ON);
       twl_i2c_write_u8(TWL6030_MODULE_ID1, 0x30, TWL6030_TOGGLE3);
       return 0;
}
late_initcall(omap_4430sdp_hack_backlight);
Signed-off-by: NArchit Taneja <archit@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

4430SDP board file contains some unused old LCD configurations. They are
not used and can be removed.
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Use default regn and regm2 dividers in the hdmi driver if the board file
does not define them.

Cc: Mythri P K <mythripk@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

There's no longer any need for the board specific
map_io.
Signed-off-by: NTony Lindgren <tony@atomide.com>

Introduce them for each omap variant and just make them all call
omap2_init_common_infrastructure for now. Do this for each board-*.c
file except for board-generic and board-omap3beagle as they use
the same machine ID for multiple SoCs.

No functional changes.
Signed-off-by: NTony Lindgren <tony@atomide.com>

There's no need to call omap2_init_common_devices from init_early.

It no longer does anything else except reprogram the memory timings
for some boards, so it's better to do it later so we have a chance
to get console messages if something goes wrong.

Move it to happen after omap_serial_init gets called. And while
patching it anyways, rename it to omap_sdrc_init as suggested by
Benoit Cousson <b-cousson@ti.com>.
Signed-off-by: NTony Lindgren <tony@atomide.com>

Signed-off-by: NNicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: NTony Lindgren <tony@atomide.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>

The mux settings for keypad  are done for omap4430sdp in
board file.
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
[tony@atomide.com: improved formatting a bit]
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add MMC5 support on BLAZE, which has the wl1283 device hardwired to.

The wl1283 is a 4-wire, 1.8V, embedded SDIO WLAN device with an external IRQ line,
and power-controlled by a GPIO-based fixed regulator.

Based on the patch for zoom by Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: NVishal Mahaveer <vishalm@ti.com>
[tony@atomide.com: improved formatting a bit]
Signed-off-by: NTony Lindgren <tony@atomide.com>

Without this the HSMMC driver takes GPIO 0 to be the card detect gpio
and requests/configures it. This will give rise to issues when another
driver needs to use GPIO 0. On 4430SDP, the card detection is through
TWL 6030.
Signed-off-by: NSilesh C V <silesh@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Configure, and enable the twl6040 codec on SDP4430.
Signed-off-by: NMisael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

Add twl4030_vibra platform data, and the needed regulators
for twl6040 vibrator.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

Reduce the amount of duplicated code by moving the common
configuration for TWL6030 (on OMAP4 platform) to the
twl-common file.
Use the omap4_pmic_get_config function from board files to
properly configure the PMIC with the common fields.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>