The legacy scan API is deprecated and not used anymore with 10 and
higher firmware versions.  Since we deprecated firmware version 9, we
can remove a whole lot of unused code.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Export the radio statistics from the statistics v10 API (if the
firmware also has the capability to fill these statistics) using
the global survey data facility.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Different queue can have different behavior. While it can be
unacceptable for a certain queue to be stuck for 2 seconds
(e.g. the command queue), it can happen that another queue
will stay stuck for even longer (a queue servicing a power
saving client in GO).
The op_mode can even make the timeout be a function of the
listen interval.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

There's really no reason to pad out the field with spaces at the
end of the line - they're practically invisible there anyway.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

A new host command can be used to configure the scheduler
instead of accessing the scheduler's registers from the
driver. This is easier and less error prone since accessing
the hardware at certain moments can lead to races with the
firmware.
Prefer to use the host command whenever it is available.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

commit 5c904224
"iwlwifi: mvm: don't allow diversity if BT Coex / TT forbid it"
broke Rx with 2 chains for diversity.
This had an impact on throughput where we're using only a single
stream (11a/b/g APs, single stream APs, static SMPS).

Fixes: 5c904224 ("iwlwifi: mvm: don't allow diversity if BT Coex / TT forbid it")
Cc: Stable <stable@vger.kernel.org>  [3.16+]
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The antenna configuration has to be read also from OTP
Currently read only from FW image
Guideline: An antenna exists only if appears both in FW image & NVM
Signed-off-by: NMoshe Harel <moshe.harel@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Getting the BSS station vif is something that may be needed by other
parts of the code.  So, instead of having an iterator specifically for
d3, change it into a generic one in utils.c.  Additionally, add a
iwl_mvm_get_bss_vif() function to make it easier to retrieving it.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The scheduler is a HW sub-block that directs the work of the Flow
Handler by issuing requests for frame transfers, specifying source
and destination. Its primary function is to allocate flows into the
TX FIFOs based upon a pre-determined mapping.

The driver has some responsibilities to the scheduler, namely
initialising and maintaining the hardware registers. This is
currently done by directly accessing them, which can cause races
with the firmware also accessing the registers.

To address this problem, change the driver to no longer directly
access the registers but go through the firmware for this if the
firmware has support for DQA and thus the new command.
Signed-off-by: NAvri Altman <avri.altman@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Our legal structure changed at some point (see wikipedia), but
we forgot to immediately switch over to the new copyright
notice.

For files that we have modified in the time since the change,
add the proper copyright notice now.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

1. the base_address limitation was wrong, address can be bigger than
0x80C000
2. the ucode data_struct changed.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Reviewed-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

It turns out that adding the update type argument was pointless as
quota update is never called from the add_interface() callback.
Therefore, IWL_MVM_QUOTA_UPDATE_TYPE_NEW isn't actually needed and
then only a "disabled_vif" argument is needed for the upcoming CSA
work.

Remove the whole enum iwl_mvm_quota_update_type and pass the right
arguments (always NULL for disabled vif right now) to the function
in all current call sites.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In some cases (e.g. when we're doing a channel switch), we may need to
disable the quota of a vif temporarily.  In order to do so, add an
argument to the iwl_mvm_update_quotas() function to tell if the passed
vif is a new one or if it should be disregarded.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Its content can move to the caller.
While at it, move iwl_mvm_fw_error_rxf_dump to caller.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Instead of reading all the data in the context of the
interrupt thread, collect the data in the restart flow
before the actual restart takes place so that the device
still has all the information.
Remove iwl_mvm_fw_error_sram_dump and move its content to
iwl_mvm_fw_error_dump.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The power update function looks at all current vifs to determine the power
policy. It doesn't use the current vif. Instead the value was overwritten
and used internally.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

We should not allow diversity when BT Coex needs the second
antenna. Thermal Throttling can also request to stop using
the second antenna. Honour those requests.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Prevent sched scan while not idle (including during association or in AP
mode) instead of while associated only.

This fixes my previous commit which was incomplete:

commit bd5e4744
Author: David Spinadel <david.spinadel@intel.com>
Date:   Thu Apr 24 13:15:29 2014 +0300

    iwlwifi: mvm: do no sched scan while associated

    Currently the FW doesn't support sched scan while associated,
    Prevent it.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

CMD_SYNC is really 0 which is confusing:

if (cmd.flags & CMD_SYNC) is always false.
Fix this by simply removing its definition.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Since the declaration of iwl_mvm_fw_error_rxf_dump and
iwl_mvm_fw_error_sram_dump is under
ifdef CONFIG_IWLWIFI_DEBUGFS, do the same for their
implementation.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Currently the FW doesn't support sched scan while associated,
Prevent it.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The Rx FIFO includes valuable data - dump it when the FW
asserts. Also - free the SRAM and Rx FIFO when we create
the file, and don't collect new SRAM / Rx FIFO if the
previous file hasn't been collected through debugfs yet.

Also - add a comment to saying that the ASSERT output should
not be modified since we have automatic scripts that monitor
this output.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

If the low-latency update is called but there's no change then
ignore the update instead of triggering all the required work.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In case of system low latency configure passive scan to be fragmented.
Set the following scan parameters for both immediate and scheduled scan:
 - passive scan fragment duration = 20ms
 - out-of-channel time = 70ms
 - suspend time = 105ms
Restructure channel's active/passive dwell time configuration to better
suit the above change.

The idea is that under low latency traffic passive scan is fragmented,
i.e. that dwell on a particular channel will be fragmented. Each
fragment dwell time is 20ms and fragments period is 105ms. Skipping to
next channel will be delayed by the same period (105ms). So suspend_time
parameter describing both fragments and channels skipping periods is set
to 105ms. This value is chosen so that overall passive scan duration
will not be too long. Max_out_time in this case is set to 70ms, so for
active scanning operating channel will be left for 70ms while for
passive still for 20ms (fragment dwell).
Signed-off-by: NAlexander Bondar <alexander.bondar@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When the firmware asserts, the driver will dump the firmware
state to an internal buffer. This buffer is kept aside until
it is dumped through debugfs. Once an external application
fetched the data, the buffer is freed and a new buffer can
be allocated in case another assert occurs.

A udev event is sent to trigger an external application.

A simple rule like:
DRIVER=="iwlwifi", ACTION=="change", RUN+="/sbin/dump_sram.sh"

can fetch the data from debugfs.

Here is my dump_sram.sh:

phyname=$(basename ${DEVPATH})
date=$(date +%F_%H_%M)
filename=/var/log/iwl-sram-${phyname}-${date}.bin
cat /sys/kernel/debug/ieee80211/${phyname}/iwlwifi/iwlmvm/fw_error_dump > ${filename}

The current SRAM size is 80KB so, currently:
$ ls -lh iwl-sram-phy0-2014-03-16_13_14.bin
-rw-r--r-- 1 emmanuel emmanuel 81K Mar 16 13:15 iwl-sram-phy0-2014-03-16_13_14.bin

and after compression:
$ ls -lh iwl-sram-phy0-2014-03-16_13_14.bin.xz
-rw-r--r-- 1 emmanuel emmanuel 13K Mar 16 13:15 iwl-sram-phy0-2014-03-16_13_14.bin.xz
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

These inlines are pretty pointless now as they just return a
fixed struct value, remove them - the code even gets shorter.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Reviewed-by: NEran Harary <eran.harary@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

There are a number of things in the .data section that should
really be in .rodata, for example all ops structs and strings.
Mark everything const that can be, leaving the .data section
pretty much empty.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Alive notification ver2 support error table information
for 2 CPUs.
This is useful to fetch the error information in case of
firmware assert.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Newer NIC have different memory layout in their SRAM,
so change the checks in iwl_mvm_dump_nic_error_log
accordingly.
Signed-off-by: NAriej Marjieh <ariej.marjieh@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The main complexity of the power code is that it needs to
take into account the firmware limitations.
These limitations state that we need to have a global
picture of the vifs present in the system to be able to
decide if we can enable power management on a specific vif.

Even device power save (as opposed to vif power management)
must be disabled in certain circumstances (monitor vif).

Refactor the current code to make this clearer by defining
a function that explicitely computes these constraints.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

If the driver detects old firmware, we disable support for
power management.
This greatly simplifies the code.
Reviewed-by: NAlexander Bondar <alexander.bondar@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

As a debug tool, we dump the SRAM from the device when an
error occurs. The main users of this want it in a different
format, so change the format to suit their needs.
Also - add a short delay between the prints to make sure
that the user space logger can catch up.

This happens only when the firmware asserts, and only when
fw_restart is set to 0 which is typically a testing
configuration.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Based on the Bluetooth activity grading, we can stop using
the shared antenna and ask the stations to honor the new
SMPS state.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

If a vif is in low latency mode, it should be in primary
channel.
Also tell BT Coex about the change when a vif enters or
exits low latency mode.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

While an interface is in low-latency mode, for now powersave
should be disabled for it, so take low-latency into account
in the powersave code and force powersave recalculation when
low-latency mode changes.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

For various traffic use cases, we want to be able to treat multi-
channel scenarios differently. Introduce a low-latency framework
that currently only has a debugfs file to enable low-latency mode,
but can later be extended.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This can be useful to be able to spot the firmware version
from the error reports without needing to fetch it from
another place.

Cc: <stable@vger.kernel.org> [3.10+]
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add an inline helper function for getting an RX packet's
length or payload length and use it throughout the code
(most of which I did using an spatch.)

While at it, adjust some code, and remove a bogus comment
from the dvm calibration code.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Reviewed-by: NEran Harary <eran.harary@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Happy new year!
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Products that have only 1 antenna in Rx don't support MIMO
in RX. As a consequence, they will be in STATIC always.
Don't tell mac80211 to update SMPS in that case. mac80211
would send an action frame to the AP which is clearly
bogus.
As a matter of fact, we have seen that some APs send a
deauth when that happens.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>