#define dbg adds the newline, messages shouldn't.
Converted dbg("%s", "some string") to dbg("some string")
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

PID patch for my products
Signed-off-by: NMitchell Solomon <mitchjs@rush2112.net>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

As Alan Cox have pinpointed the driver still required protection against
parallels calls to the config ioctl(). If lock is still necessary the use of
BKL is abused here. So replace BKL with a more convenient mutex.
Signed-off-by: NAlessio Igor Bogani <abogani@texware.it>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- correct spelling
- correct non-tabbed .tiocmget/.tiocmset entries
Signed-off-by: NAndreas Mohr <andi@lisas.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Return values are being initialised to zero only to be unconditionally
assigned to a few instructions later. This may give the impression that
zero is returned on success, which is not the case.

Note also that ftdi_NDI_device_setup never reports errors.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Also remove unnecessary buffer allocations for zero-length transfers.
Reported-by: NMatti Aarnio <matti.aarnio@zmailer.org>
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Also fixes DMA transfer to stack for latency buffer.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Use same semantics as for write_latency_timer.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Removed CS5 and CS6 from data bits since these are not supported
in FTDI hardware.
Signed-off-by: NMark J. Adamson <mark.adamson@ftdichip.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Latency timeout was read but never stored on port probe. When
ASYNC_LOW_LATENCY was cleared the device timeout would get set to 0
rather than the default 16ms.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

We always push characters to ldisc immediately regardless of
ASYNC_LOW_LATENCY.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Resubmitting read urb fails with -EPERM if completion handler runs while
urb is being killed on close. This should not be reported as an error.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- add FTDI device IDs for several ELV devices and NXTCam of Lego Mindstorms NXT
- add hopefully helpful new_id comment
- remove less helpful "Due to many user requests for multiple ELV devices we enable
  them by default." comment (we simply add _all_ known devices - an
  enduser shouldn't have to fiddle with obscure module parameters...).
- add myself to DRIVER_AUTHOR

The missing NXTCam ID has been found at
http://www.unixboard.de/vb3/showthread.php?t=44155
, ELV devices taken from ELV Windows .inf file.
Signed-off-by: NAndreas Mohr <andi@lisas.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

added new device pid (PAPOUCH_AD4USB_PID) to ftdi_sio.h and ftdi_sio.c

AD4USB measuring converter is a 4-input A/D converter which enables the
user to measure to four current inputs ranging from 0(4) to 20 mA or
voltage between 0 and 10 V. The measured values are then transferred to
a superior system in digital form. The AD4USB communicates via USB.
Powered is also via USB.  datasheet in english is here:
http://www.papouch.com/shop/scripts/pdf/ad4usb_en.pdfSigned-off-by: NRadek Liboska <liboska@uochb.cas.cz>

This is a strictly move-only patch to relocate all FTDI device
product ID definitions to their own ftdi_sio_ids.h header
(following the usual *_ids.h kernel tree convention, too),
thus correcting the slightly too messy appearance
(crucial driver defines were stuck somewhere in the decaying middle swamp
of the huge existing header).

Compile-tested, based on latest mainline git.
Signed-off-by: NAndreas Mohr <andi@lisas.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Reviewed-by: NJohn Pilles <jpilles@bb-elec.com>
Signed-off-by: NCliff Brake <cbrake@bec-systems.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add mark and space parity, since the device supports it.
Signed-off-by: NRoland Koebler <r.koebler@yahoo.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The use of urb->actual_length to update tx_outstanding_bytes
implicitly assumes that the number of bytes actually written is the
same as the number of bytes we tried to write.  On error that
assumption is violated so just use transfer_buffer_length the number
of bytes we intended to write to the device.

If an error occurs we need to fall through and call
usb_serial_port_softint to wake up processes waiting in
tty_wait_until_sent.
Signed-off-by: NEric W. Biederman <ebiederm@aristanetworks.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- Re-structure read processing.
 - Kill obsolete work queue and always push to tty in completion handler.
 - Use tty_insert_flip_string instead of per character push when
   possible.
 - Fix stalled-read regression in 2.6.31 by using urb status to
   determine when port is closed rather than port count.
 - Fix race with open/close by checking ASYNCB_INITIALIZED in
   unthrottle.
 - Kill private rx_flag and lock and use throttle flags in
   usb_serial_port instead.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove superfluous error checks in completion handler:

 - No need to check private data and urb pointers as we check urb-status
   before dereferencing priv (which is not freed until urb has been killed
   on close).
 - No need to check tty as it is checked again when processing.
 - No need to check urb->number_of_packets on bulk urb.

Note that both private data and tty are checked again before processing
(possibly from work queue which also is cancelled on close).
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove unused rx_byte counter which is never exposed as noted by Alan
Cox.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fixes tty_flip_buffer_push being called from hard interrupt context with
low_latency set.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Detect the UART on interface1 and blacklist interface0 (as that is the
JTAG port).
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Some devices from the OpenDCC project are missing in the list
of the FTDI PIDs. These PIDs are listed at
http://www.opendcc.de/elektronik/usb/opendcc_usb.html
(Sorry for the german only page.)
This patch adds the three missing devices.
Signed-off-by: NRainer Keller <mail@rainerkeller.de>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I'd like to present my small patch enabling to use Hameg HM8143 programmable
power supply with linux.
Signed-off-by: NPawel Ludwikow <pludwiko@rab.ict.pwr.wroc.pl>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

And indeed none of them use it. Clean this up as it will make moving to a
standard open method rather easier.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

reference:
http://www.open-rd.orgSigned-off-by: NDhaval Vasa <dhaval.vasa@einfochips.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Attached patch adds USB vendor and product IDs for Bayer's USB to serial
converter cable used by Bayer blood glucose meters. It seems to be a
FT232RL based device and works without any problem with ftdi_sio driver
when this patch is applied. See: http://winglucofacts.com/cables/Signed-off-by: NMarko Hänninen <bugitus@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The patch adds support for the GN Otometrics Aurical USB Audiometer
(FT232BM-based).
A new VID and a new PID is added.
Signed-off-by: NVille Sundberg <vsundber@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Adds USB ID for Turtelizer, an FT2232L-based JTAG/RS-232 adapter.
Signed-off-by: NKrzysztof Ha³asa <khc@pm.waw.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

It enhances the driver for FTDI-based USB serial adapters to recognize and
support Northern Digital Inc (NDI) measurement equipment. NDI has been
providing this patch for various kernel flavors for several years and we would
like to see these changes built in to the driver so that our equipement works
without the need for customers to patch the kernel themselves.

The patch makes small modifications to 2 files: ./drivers/usb/serial/ftdi_sio.c
and ./drivers/usb/serial/ftdi_sio.h. It accomplishes 3 things:

1. Define the VID and PIDs to allow the driver to recognize the NDI devices.
2. Map the 19200 baud rate setting to our higher baud rate of 1.2Mb
   We would have chosen to map 38400 to the higher rate, similar to what
   several other vendors have done, but some of our legacy customers actually
   use 38400, therefore we remap 19200 to the higher rate.
3. We set the default transmit latency in the FTDI chip to 1ms for our devices.
   Our devices are typically polled at 60Hz and the default ftdi latency
   seriously affects turn-around time and results in missed data frames. We
   have created a modprobe option that allows this setting to be increased.
   This has proven necessary particularly in some virtualized environments.
Signed-off-by: NMartin P. Geleynse <mgeleyns@ndigital.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

It seems an USB device with vendor id 0403 and product code FB80 has an
FTDI serial io chip as well: http://ftdichip.com/Drivers/D2XX.htm
This device in fact is a true random generantor by comsci:
http://comscire.com/Products/R2000KU/
So the following patch should add support for this device if I am
correct. Not tested as I do not own this device (I would like support in
the kernel so that my entropybroker application (which distributes
entrop data (random values) between servers and clients)).


From: Folkert van Heusden <folkert@vanheusden.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The product ID's for the following devices have been added:
- LOAD-n-GO
- ICD-U64
- PRIME-8
Signed-off-by: NJan Capek <jan@ccsinfo.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

* Remove smp_lock.h from files which don't need it (including some headers!)
* Add smp_lock.h to files which do need it
* Make smp_lock.h include conditional in hardirq.h
  It's needed only for one kernel_locked() usage which is under CONFIG_PREEMPT

  This will make hardirq.h inclusion cheaper for every PREEMPT=n config
  (which includes allmodconfig/allyesconfig, BTW)
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The sysrq code acquired a kref leak. Fix it by passing the tty separately
from the caller (thus effectively using the callers kref which all the
callers hold anyway)
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch (as1254) splits up the shutdown method of usb_serial_driver
into a disconnect and a release method.

The problem is that the usb-serial core was calling shutdown during
disconnect handling, but drivers didn't expect it to be called until
after all the open file references had been closed.  The result was an
oops when the close method tried to use memory that had been
deallocated by shutdown.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Change driver to make use of the new functions in
include/linux/usb/serial.h so as to allow the driver to handle the
sysrq
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Alan Stern commented that the private driver counts must be updated
regard less of the status return on the urb when the write call back
is executed.

This patch alters the behavior to update the private driver counts by
simply moving the status check to after the driver count update.
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Added a function to set the packet size to be used based on the value from the
device endpoint descriptor.  The FT2232H and FT4232H hi-speed devices will have
wMaxPacketSize of 512 bytes when connected to a USB 2.0 hi-speed host, but will
use alternative descriptors with wMaxPacketSize of 64 bytes if connected to a
USB 1.1 host or hub.  All other FTDI devices have wMaxPacketSize of 64 bytes,
except some FT232R and FT245R devices which customers have mistakenly
programmed to have wMaxPacketSize of 0 - this is an error and will be
overridden to use wMaxPacketSize of 64 bytes.  The packet size used is
important as it determines where the driver removes the status bytes from the
incoming data.  If it is incorrect, it will lead to data corruption.
Signed-off-by: NMark J. Adamson <mark.adamson@ftdichip.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>