Public Action frames use special rules for how the BSSID field (Address
3) is set. A wildcard BSSID is used in cases where the transmitter and
recipient are not members of the same BSS. As such, we need to accept
Public Action frames with wildcard BSSID.

Commit db8e1732 ("mac80211: ignore frames between TDLS peers when
operating as AP") added a rule that drops Action frames to TDLS-peers
based on an Action frame having different DA (Address 1) and BSSID
(Address 3) values. This is not correct since it misses the possibility
of BSSID being a wildcard BSSID in which case the Address 1 would not
necessarily match.

Fix this by allowing mac80211 to accept wildcard BSSID in an Action
frame when in AP mode.

Fixes: db8e1732 ("mac80211: ignore frames between TDLS peers when operating as AP")
Cc: stable@vger.kernel.org
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Just like for CCMP we need to check that for GCMP the fragments
have PNs that increment by one; the spec was updated to fix this
security issue and now has the following text:

	The receiver shall discard MSDUs and MMPDUs whose constituent
	MPDU PN values are not incrementing in steps of 1.

Adapt the code for CCMP to work for GCMP as well, luckily the
relevant fields already alias each other so no code duplication
is needed (just check the aliasing with BUILD_BUG_ON.)

Cc: stable@vger.kernel.org
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When user-space has started a critical protocol session and a disconnect
event occurs, the rdev::crit_prot_nlportid remains set. This caused a
subsequent NL80211_CMD_CRIT_PROTO_START to fail (-EBUSY). Fix this by
clearing the rdev attribute and call .crit_proto_stop() callback upon
disconnect event.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The connection keys are zeroed out in all other cases except this
one. Let's fix the last one as well.
Signed-off-by: NOla Olsson <ola.olsson@sonymobile.com>
Reviewed-by: NJulian Calaby <julian.calaby@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The value 5000 was put here with the addition of the timeout field to
ieee80211_start_tx_ba_session. It was originally added in mac80211 to
save resources for drivers like iwlwifi, which only supports a limited
number of concurrent aggregation sessions.

Since iwlwifi does not use minstrel_ht and other drivers don't need
this, 0 is a better default - especially since there have been
recent reports of aggregation setup related issues reproduced with
ath9k. This should improve stability without causing any adverse
effects.

Cc: stable@vger.kernel.org
Acked-by: NAvery Pennarun <apenwarr@gmail.com>
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The change from cur_tp to the function
minstrel_get_tp_avg/minstrel_ht_get_tp_avg changed the unit used for the
current throughput. For example in minstrel_ht the correct
conversion between them would be:

    mrs->cur_tp / 10 == minstrel_ht_get_tp_avg(..).

This factor 10 must also be included in the calculation of
minstrel_get_expected_throughput and minstrel_ht_get_expected_throughput to
return values with the unit [Kbps] instead of [10Kbps]. Otherwise routing
algorithms like B.A.T.M.A.N. V will make incorrect decision based on these
values. Its kernel based implementation expects expected_throughput always
to have the unit [Kbps] and not sometimes [10Kbps] and sometimes [Kbps].

The same requirement has iw or olsrdv2's nl80211 based statistics module
which retrieve the same data via NL80211_STA_INFO_TX_BITRATE.

Cc: stable@vger.kernel.org
Fixes: 6a27b2c4 ("mac80211: restructure per-rate throughput calculation into function")
Signed-off-by: NSven Eckelmann <sven@open-mesh.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Patch fixes this splat

BUG: KASAN: slab-out-of-bounds in minstrel_ht_update_stats.isra.7+0x6e1/0x9e0
[mac80211] at addr ffff8800cee640f4 Read of size 4 by task swapper/3/0
Signed-off-by: NKonstantin Khlebnikov <koct9i@gmail.com>
Link: http://lkml.kernel.org/r/CALYGNiNyJhSaVnE35qS6UCGaSb2Dx1_i5HcRavuOX14oTz2P+w@mail.gmail.comAcked-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Use kzalloc instead of kmalloc for struct tid_ampdu_rx to
initialize the "removed" field (all others are initialized
manually). That fixes:

UBSAN: Undefined behaviour in net/mac80211/rx.c:932:29
load of value 2 is not a valid value for type '_Bool'
CPU: 3 PID: 1134 Comm: kworker/u16:7 Not tainted 4.5.0-rc1+ #265
Workqueue: phy0 rt2x00usb_work_rxdone
 0000000000000004 ffff880254a7ba50 ffffffff8181d866 0000000000000007
 ffff880254a7ba78 ffff880254a7ba68 ffffffff8188422d ffffffff8379b500
 ffff880254a7bab8 ffffffff81884747 0000000000000202 0000000348620032
Call Trace:
 [<ffffffff8181d866>] dump_stack+0x45/0x5f
 [<ffffffff8188422d>] ubsan_epilogue+0xd/0x40
 [<ffffffff81884747>] __ubsan_handle_load_invalid_value+0x67/0x70
 [<ffffffff82227b4d>] ieee80211_sta_reorder_release.isra.16+0x5ed/0x730
 [<ffffffff8222ca14>] ieee80211_prepare_and_rx_handle+0xd04/0x1c00
 [<ffffffff8222db03>] __ieee80211_rx_handle_packet+0x1f3/0x750
 [<ffffffff8222e4a7>] ieee80211_rx_napi+0x447/0x990

While at it, convert to use sizeof(*tid_agg_rx) instead.

Fixes: 788211d8 ("mac80211: fix RX A-MPDU session reorder timer deletion")
Cc: stable@vger.kernel.org
Signed-off-by: NChris Bainbridge <chris.bainbridge@gmail.com>
[reword commit message, use sizeof(*tid_agg_rx)]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Since cfg80211 frequently takes actions from its netdev notifier
call, wireless extensions messages could still be ordered badly
since the wext netdev notifier, since wext is built into the
kernel, runs before the cfg80211 netdev notifier. For example,
the following can happen:

5: wlan1: <BROADCAST,MULTICAST> mtu 1500 qdisc mq state DOWN group default
    link/ether 02:00:00:00:01:00 brd ff:ff:ff:ff:ff:ff
5: wlan1: <BROADCAST,MULTICAST,UP>
    link/ether

when setting the interface down causes the wext message.

To also fix this, export the wireless_nlevent_flush() function
and also call it from the cfg80211 notifier.

Cc: stable@vger.kernel.org
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Beniamino reported that he was getting an RTM_NEWLINK message for a
given interface, after the RTM_DELLINK for it. It turns out that the
message is a wireless extensions message, which was sent because the
interface had been connected and disconnection while it was deleted
caused a wext message.

For its netlink messages, wext uses RTM_NEWLINK, but the message is
without all the regular rtnetlink attributes, so "ip monitor link"
prints just rudimentary information:

5: wlan1: <BROADCAST,MULTICAST> mtu 1500 qdisc mq state DOWN group default
    link/ether 02:00:00:00:01:00 brd ff:ff:ff:ff:ff:ff
Deleted 5: wlan1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default
    link/ether 02:00:00:00:01:00 brd ff:ff:ff:ff:ff:ff
5: wlan1: <BROADCAST,MULTICAST,UP>
    link/ether
(from my hwsim reproduction)

This can cause userspace to get confused since it doesn't expect an
RTM_NEWLINK message after RTM_DELLINK.

The reason for this is that wext schedules a worker to send out the
messages, and the scheduling delay can cause the messages to get out
to userspace in different order.

To fix this, have wext register a netdevice notifier and flush out
any pending messages when netdevice state changes. This fixes any
ordering whenever the original message wasn't sent by a notifier
itself.

Cc: stable@vger.kernel.org
Reported-by: NBeniamino Galvani <bgalvani@redhat.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The code within wait_event_interruptible() is called with
!TASK_RUNNING, so mustn't call any functions that can sleep,
like mutex_lock().

Since we re-check the list_empty() in a loop after the wait,
it's safe to simply use list_empty() without locking.

This bug has existed forever, but was only discovered now
because all userspace implementations, including the default
'rfkill' tool, use poll() or select() to get a readable fd
before attempting to read.

Cc: stable@vger.kernel.org
Fixes: c64fb016 ("rfkill: create useful userspace interface")
Reported-by: NDmitry Vyukov <dvyukov@google.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

During a sw scan ieee80211_iface_work ignores work items for all vifs.
However after the scan complete work is requeued only for STA, ADHOC
and MESH iftypes.

This occasionally results in event processing getting delayed/not
processed for iftype AP when it coexists with a STA. This can result
in data halt and eventually disconnection on the AP interface.

Cc: stable@vger.kernel.org
Signed-off-by: NSachin Kulkarni <Sachin.Kulkarni@imgtec.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Non-bufferable MMPDUs are sent out to STAs even while in PS mode
(for example probe responses). Applying filtered frame handling for
these doesn't seem to make much sense and will only create more
air utilization when the STA wakes up. Hence, apply filtered frame
handling only for bufferable MMPDUs.

Discovered while testing an old VOIP phone that started probing
for APs while in PS mode. The mac80211/ath9k AP where the STA is
associated would reply with a probe response but the phone sometimes
moved to a new channel already and couldn't ack the probe response
anymore. In that case mac80211 applied filtered frame handling
for the un-acked probe response.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

On hw restart, mac80211 might try to reconfigure already
stopped sched scan, if ieee80211_sched_scan_stopped_work()
wasn't scheduled yet.

This in turn will keep the device driver with scheduled scan
configured, while both mac80211 and cfg80211 will clear
their sched scan state once the work is scheduled.

Fix it by ignoring ieee80211_sched_scan_stopped() calls
while in hw restart, and flush the work before starting
the reconfiguration.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

My commit below broken PS-Poll handling. In case the driver
has no frames buffered, driver_release_tids will be 0, but
calling find_highest_prio_tid() with 0 as a parameter is
not a good idea:
fls(0) - 1 = -1.
This bug caused mac80211 to think that frames were buffered
in the driver which in turn was confused because mac80211
was asking to release frames that were not reported to
exist.
On iwlwifi, this led to the WARNING below:

WARNING: CPU: 0 PID: 11230 at drivers/net/wireless/intel/iwlwifi/mvm/sta.c:1733 iwl_mvm_sta_modify_sleep_tx_count+0x2af/0x320 [iwlmvm]()
ffffffffc0627c60 ffff8800069b7648 ffffffff81888913 0000000000000000
0000000000000000 ffff8800069b7688 ffffffff81089d6a ffff8800069b7678
0000000000000001 ffff88003b35abf0 ffff88000698b128 ffff8800069b76d4
Call Trace:
[<ffffffff81888913>] dump_stack+0x4c/0x65
[<ffffffff81089d6a>] warn_slowpath_common+0x8a/0xc0
[<ffffffff81089e5a>] warn_slowpath_null+0x1a/0x20
[<ffffffffc05f36bf>] iwl_mvm_sta_modify_sleep_tx_count+0x2af/0x320 [iwlmvm]
[<ffffffffc05dae41>] iwl_mvm_mac_release_buffered_frames+0x31/0x40 [iwlmvm]
[<ffffffffc045d8b6>] ieee80211_sta_ps_deliver_response+0x6e6/0xd80 [mac80211]
[<ffffffffc0461296>] ieee80211_sta_ps_deliver_poll_response+0x26/0x30 [mac80211]
[<ffffffffc048f743>] ieee80211_rx_handlers+0xa83/0x2900 [mac80211]
[<ffffffffc04917ad>] ieee80211_prepare_and_rx_handle+0x1ed/0xa70 [mac80211]
[<ffffffffc045e3d5>] ? sta_info_get_bss+0x5/0x4a0 [mac80211]
[<ffffffffc04925b6>] ieee80211_rx_napi+0x586/0xcd0 [mac80211]
[<ffffffffc05eaa3e>] iwl_mvm_rx_rx_mpdu+0x59e/0xc60 [iwlmvm]

Fixes: 0ead2510 ("mac80211: allow the driver to send EOSP when needed")
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

On reconfig, in case of sched_scan_req->n_scan_plans > 1,
local->sched_scan_req was never cleared, although
cfg80211_sched_scan_stopped_rtnl() was called, resulting
in local->sched_scan_req holding a stale and preventing
further scheduled scan requests.

Clear it explicitly in this case.

Fixes: 42a7e82c6792 ("mac80211: Do not restart scheduled scan if multiple scan plans are set")
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Defer ROC requests during hw restart, as the driver
might not be fully configured in this stage (e.g.
channel contexts were not added yet)
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The rule definitions here aren't really valid, they would
be rejected if it came from userspace due to the bandwidth
specified being bigger than the rule's width.

This is fairly much inconsequential since the other rules
around them do enable the bandwidth, but express that better
using the NL80211_RRF_AUTO_BW flag.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

cfg80211 module prints a lot of messages like below. Actually printing
once is acceptable but sometimes it will print again and again, it looks
very annoying. It is better to change these detail messages to debugging
only.

cfg80211: World regulatory domain updated:
cfg80211:  DFS Master region: unset
cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)

The changes in this patch is to replace pr_info with pr_debug in function
print_rd_rules and print_regdomain_info
Signed-off-by: NDave Young <dyoung@redhat.com>
[change some pr_err() statements to at least keep the alpha2]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Ilan's previous commit 1b894521 ("mac80211: handle HW
ROC expired properly") neglected to take into account that
hw_begun was now always set in the software implementation
as well as the offloaded case.

Fix hw_begun to only apply to the offloaded case to make
the check in Ilan's commit safe and correct.
Reported-by: NJouni Malinen <j@w1.fi>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The current (new) code recalculates the new work timeout
for software remain-on-channel whenever any item started.
In two of the callers of ieee80211_handle_roc_started(),
this is completely pointless since they're for hardware
and will skip the recalculation entirely; it's necessary
only in the case of having just added a new item to the
list, as in the last remaining case the recalculation had
just been done.

This last case, however, is also problematic - if one of
the items on the list actually expires during the recalc
the list iteration outside becomes corrupted and crashes.

Fix this by moving the recalculation to the only place
where it's required.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The bug fix for adding n_groups to the computation forgot
to adjust ">=" to ">" to keep the condition correct.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The neigh_list with batadv_hardif_neigh_node objects is accessed with only
rcu_read_lock in batadv_hardif_neigh_get and batadv_iv_neigh_print. Thus it
is not allowed to kfree the object before the rcu grace period ends (which
may still protects context accessing this object). Therefore the object has
first to be removed from the neigh_list and then it has either wait with
synchronize_rcu or call_rcu till the grace period ends before it can be
freed.

Fixes: cef63419 ("batman-adv: add list of unique single hop neighbors per hard-interface")
Signed-off-by: NSven Eckelmann <sven@narfation.org>
Signed-off-by: NMarek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: NAntonio Quartulli <a@unstable.cc>

While testing, we got something like this:

WARNING: CPU: 0 PID: 238 at net/batman-adv/multicast.c:142 batadv_mcast_mla_tt_retract+0x94/0x205 [batman_adv]()
[...]
Call Trace:
[<ffffffff815fc597>] dump_stack+0x4b/0x64
[<ffffffff810b34dc>] warn_slowpath_common+0xbc/0x120
[<ffffffffa0024ec5>] ? batadv_mcast_mla_tt_retract+0x94/0x205 [batman_adv]
[<ffffffff810b3705>] warn_slowpath_null+0x15/0x20
[<ffffffffa0024ec5>] batadv_mcast_mla_tt_retract+0x94/0x205 [batman_adv]
[<ffffffffa00273fe>] batadv_mcast_free+0x36/0x39 [batman_adv]
[<ffffffffa0020c77>] batadv_mesh_free+0x7d/0x13f [batman_adv]
[<ffffffffa0036a6b>] batadv_softif_free+0x15/0x25 [batman_adv]
[...]
Signed-off-by: NSimon Wunderlich <simon@open-mesh.com>
Signed-off-by: NMarek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: NAntonio Quartulli <a@unstable.cc>

On ARM64, a BUG() is triggered in the eBPF JIT if a filter with a
constant shift that can't be encoded in the immediate field of the
UBFM/SBFM instructions is passed to the JIT.  Since these shifts
amounts, which are negative or >= regsize, are invalid, reject them in
the eBPF verifier and the classic BPF filter checker, for all
architectures.
Signed-off-by: NRabin Vincent <rabin@rab.in>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Multicast groups are stored in global buffer. Check for needed buffer size
incorrectly compares buffer size to first id for family. This means that
for families with more than one mcast id one may allocate too small buffer
and end up writing rest of the groups to some unallocated memory. Fix the
buffer size check to compare allocated space to last mcast id for the
family.

Tested on ARM using kernel 3.14
Signed-off-by: NMatti Vaittinen <matti.vaittinen@nokia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On ARM64, a BUG() is triggered in the eBPF JIT if a filter with a
constant shift that can't be encoded in the immediate field of the
UBFM/SBFM instructions is passed to the JIT.  Since these shifts
amounts, which are negative or >= regsize, are invalid, reject them in
the eBPF verifier and the classic BPF filter checker, for all
architectures.
Signed-off-by: NRabin Vincent <rabin@rab.in>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ivaylo Dimitrov reported a regression caused by commit 7866a621
("dev: add per net_device packet type chains").

skb->dev becomes NULL and we crash in __netif_receive_skb_core().

Before above commit, different kind of bugs or corruptions could happen
without major crash.

But the root cause is that phonet_rcv() can queue skb without checking
if skb is shared or not.

Many thanks to Ivaylo Dimitrov for his help, diagnosis and tests.
Reported-by: NIvaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Tested-by: NIvaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Remi Denis-Courmont <courmisch@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit acf8dd0a ("udp: only allow UFO for packets from SOCK_DGRAM
sockets") disallows UFO for packets sent from raw sockets. We need to do
the same also for SOCK_DGRAM sockets with SO_NO_CHECK options, even if
for a bit different reason: while such socket would override the
CHECKSUM_PARTIAL set by ip_ufo_append_data(), gso_size is still set and
bad offloading flags warning is triggered in __skb_gso_segment().

In the IPv6 case, SO_NO_CHECK option is ignored but we need to disallow
UFO for packets sent by sockets with UDP_NO_CHECK6_TX option.
Signed-off-by: NMichal Kubecek <mkubecek@suse.cz>
Tested-by: NShannon Nelson <shannon.nelson@intel.com>
Acked-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix possible null pointer dereference that may occur when calling
skb_reserve() on a null skb.

Fixes: 879c7220 ("net: pktgen: Observe needed_headroom of the device")
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After IPv6 support has recently been added to metadata dst and related
encaps, add support for populating/reading it from an eBPF program.

Commit d3aa45ce ("bpf: add helpers to access tunnel metadata") started
with initial IPv4-only support back then (due to IPv6 metadata support
not being available yet).

To stay compatible with older programs, we need to test for the passed
structure size. Also TOS and TTL support from the ip_tunnel_info key has
been added. Tested with vxlan devs in collect meta data mode with IPv4,
IPv6 and in compat mode over different network namespaces.
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Export flags used by eBPF helper functions through UAPI, so they can be
used by programs (instead of them redefining all flags each time or just
using the hard-coded values). It also gives a better overview what flags
are used where and we can further get rid of the extra macros defined in
filter.c. Moreover, reject invalid flags.
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

only when user space passes the addresses should we consider their
presence
Signed-off-by: NJamal Hadi Salim <jhs@mojatatu.com>
Acked-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For tcp_yeah, use an ssthresh floor of 2, the same floor used by Reno
and CUBIC, per RFC 5681 (equation 4).

tcp_yeah_ssthresh() was sometimes returning a 0 or negative ssthresh
value if the intended reduction is as big or bigger than the current
cwnd. Congestion control modules should never return a zero or
negative ssthresh. A zero ssthresh generally results in a zero cwnd,
causing the connection to stall. A negative ssthresh value will be
interpreted as a u32 and will set a target cwnd for PRR near 4
billion.

Oleksandr Natalenko reported that a system using tcp_yeah with ECN
could see a warning about a prior_cwnd of 0 in
tcp_cwnd_reduction(). Testing verified that this was due to
tcp_yeah_ssthresh() misbehaving in this way.
Reported-by: NOleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NYuchung Cheng <ycheng@google.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Dmitry Vyukov reported a use-after-free in the code expanded by the
macro debug_post_sfx, which is caused by the use of the asoc pointer
after it was freed within sctp_side_effect() scope.

This patch fixes it by allowing sctp_side_effect to clear that asoc
pointer when the TCB is freed.

As Vlad explained, we also have to cover the SCTP_DISPOSITION_ABORT case
because it will trigger DELETE_TCB too on that same loop.

Also, there were places issuing SCTP_CMD_INIT_FAILED and ASSOC_FAILED
but returning SCTP_DISPOSITION_CONSUME, which would fool the scheme
above. Fix it by returning SCTP_DISPOSITION_ABORT instead.

The macro is already prepared to handle such NULL pointer.
Reported-by: NDmitry Vyukov <dvyukov@google.com>
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: NVlad Yasevich <vyasevich@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The sz_idx variable is defined in the rtnetlink_rcv_msg(), but
not used anywhere. Let's remove it.
Signed-off-by: NAlexander Kuleshov <kuleshovmail@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is possible for a process to allocate and accumulate far more FDs than
the process' limit by sending them over a unix socket then closing them
to keep the process' fd count low.

This change addresses this problem by keeping track of the number of FDs
in flight per user and preventing non-privileged processes from having
more FDs in flight than their configured FD limit.

Reported-by: socketpair@gmail.com
Reported-by: NTetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Mitigates: CVE-2013-4312 (Linux 2.0+)
Suggested-by: NLinus Torvalds <torvalds@linux-foundation.org>
Acked-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NWilly Tarreau <w@1wt.eu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit be4ace6e ("openvswitch: Move dev pointer into vport itself")

The commit above added @dev and moved @rcu to the bottom of struct
vport, but the change was not reflected in the kernel doc. So let's
update the kernel doc as well.
Signed-off-by: NJean Sacren <sakiwit@gmail.com>
Cc: Thomas Graf <tgraf@suug.ch>
Acked-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 6b001e68 ("openvswitch: Use Geneve device.")

The commit above introduced 'port_no' as the name for the member of
struct geneve_port. The correct name should be 'dst_port' as described
in the kernel doc. Let's fix that member name and all the pertinent
instances so that both doc and code would be consistent.
Signed-off-by: NJean Sacren <sakiwit@gmail.com>
Acked-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 6b001e68 ("openvswitch: Use Geneve device.")

The commit above deleted the only call site of ovs_tunnel_route_lookup()
and now that function is not used any more. So let's delete the function
definition as well.
Signed-off-by: NJean Sacren <sakiwit@gmail.com>
Acked-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>