Remove now unnecessary inclusions of {asm,linux}/a.out.h.

[akpm@linux-foundation.org: fix alpha build]
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Suppress A.OUT library support if CONFIG_ARCH_SUPPORTS_AOUT is not set.

Not all architectures support the A.OUT binfmt, so the ELF binfmt should not
be permitted to go looking for A.OUT libraries to load in such a case.  Not
only that, but under such conditions A.OUT core dumps are not produced either.

To make this work, this patch also does the following:

 (1) Makes the existence of the contents of linux/a.out.h contingent on
     CONFIG_ARCH_SUPPORTS_AOUT.

 (2) Renames dump_thread() to aout_dump_thread() as it's only called by A.OUT
     core dumping code.

 (3) Moves aout_dump_thread() into asm/a.out-core.h and makes it inline.  This
     is then included only where needed.  This means that this bit of arch
     code will be stored in the appropriate A.OUT binfmt module rather than
     the core kernel.

 (4) Drops A.OUT support for Blackfin (according to Mike Frysinger it's not
     needed) and FRV.

This patch depends on the previous patch to move STACK_TOP[_MAX] out of
asm/a.out.h and into asm/processor.h as they're required whether or not A.OUT
format is available.

[jdike@addtoit.com: uml: re-remove accidentally restored code]
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove fs.h from mm.h. For this,
 1) Uninline vma_wants_writenotify(). It's pretty huge anyway.
 2) Add back fs.h or less bloated headers (err.h) to files that need it.

As result, on x86_64 allyesconfig, fs.h dependencies cut down from 3929 files
rebuilt down to 3444 (-12.3%).

Cross-compile tested without regressions on my two usual configs and (sigh):

alpha              arm-mx1ads        mips-bigsur          powerpc-ebony
alpha-allnoconfig  arm-neponset      mips-capcella        powerpc-g5
alpha-defconfig    arm-netwinder     mips-cobalt          powerpc-holly
alpha-up           arm-netx          mips-db1000          powerpc-iseries
arm                arm-ns9xxx        mips-db1100          powerpc-linkstation
arm-assabet        arm-omap_h2_1610  mips-db1200          powerpc-lite5200
arm-at91rm9200dk   arm-onearm        mips-db1500          powerpc-maple
arm-at91rm9200ek   arm-picotux200    mips-db1550          powerpc-mpc7448_hpc2
arm-at91sam9260ek  arm-pleb          mips-ddb5477         powerpc-mpc8272_ads
arm-at91sam9261ek  arm-pnx4008       mips-decstation      powerpc-mpc8313_rdb
arm-at91sam9263ek  arm-pxa255-idp    mips-e55             powerpc-mpc832x_mds
arm-at91sam9rlek   arm-realview      mips-emma2rh         powerpc-mpc832x_rdb
arm-ateb9200       arm-realview-smp  mips-excite          powerpc-mpc834x_itx
arm-badge4         arm-rpc           mips-fulong          powerpc-mpc834x_itxgp
arm-carmeva        arm-s3c2410       mips-ip22            powerpc-mpc834x_mds
arm-cerfcube       arm-shannon       mips-ip27            powerpc-mpc836x_mds
arm-clps7500       arm-shark         mips-ip32            powerpc-mpc8540_ads
arm-collie         arm-simpad        mips-jazz            powerpc-mpc8544_ds
arm-corgi          arm-spitz         mips-jmr3927         powerpc-mpc8560_ads
arm-csb337         arm-trizeps4      mips-malta           powerpc-mpc8568mds
arm-csb637         arm-versatile     mips-mipssim         powerpc-mpc85xx_cds
arm-ebsa110        i386              mips-mpc30x          powerpc-mpc8641_hpcn
arm-edb7211        i386-allnoconfig  mips-msp71xx         powerpc-mpc866_ads
arm-em_x270        i386-defconfig    mips-ocelot          powerpc-mpc885_ads
arm-ep93xx         i386-up           mips-pb1100          powerpc-pasemi
arm-footbridge     ia64              mips-pb1500          powerpc-pmac32
arm-fortunet       ia64-allnoconfig  mips-pb1550          powerpc-ppc64
arm-h3600          ia64-bigsur       mips-pnx8550-jbs     powerpc-prpmc2800
arm-h7201          ia64-defconfig    mips-pnx8550-stb810  powerpc-ps3
arm-h7202          ia64-gensparse    mips-qemu            powerpc-pseries
arm-hackkit        ia64-sim          mips-rbhma4200       powerpc-up
arm-integrator     ia64-sn2          mips-rbhma4500       s390
arm-iop13xx        ia64-tiger        mips-rm200           s390-allnoconfig
arm-iop32x         ia64-up           mips-sb1250-swarm    s390-defconfig
arm-iop33x         ia64-zx1          mips-sead            s390-up
arm-ixp2000        m68k              mips-tb0219          sparc
arm-ixp23xx        m68k-amiga        mips-tb0226          sparc-allnoconfig
arm-ixp4xx         m68k-apollo       mips-tb0287          sparc-defconfig
arm-jornada720     m68k-atari        mips-workpad         sparc-up
arm-kafa           m68k-bvme6000     mips-wrppmc          sparc64
arm-kb9202         m68k-hp300        mips-yosemite        sparc64-allnoconfig
arm-ks8695         m68k-mac          parisc               sparc64-defconfig
arm-lart           m68k-mvme147      parisc-allnoconfig   sparc64-up
arm-lpd270         m68k-mvme16x      parisc-defconfig     um-x86_64
arm-lpd7a400       m68k-q40          parisc-up            x86_64
arm-lpd7a404       m68k-sun3         powerpc              x86_64-allnoconfig
arm-lubbock        m68k-sun3x        powerpc-cell         x86_64-defconfig
arm-lusl7200       mips              powerpc-celleb       x86_64-up
arm-mainstone      mips-atlas        powerpc-chrp32
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The current scheme works on static interpretation of text names, which
is wrong.

The output-device setting, for example, must be resolved via an alias
or similar to a full path name to the console device.

Paths also contain an optional set of 'options', which starts with a
colon at the end of the path.  The option area is used to specify
which of two serial ports ('a' or 'b') the path refers to when a
device node drives multiple ports.  'a' is assumed if the option
specification is missing.

This was caught by the UltraSPARC-T1 simulator.  The 'output-device'
property was set to 'ttya' and we didn't pick upon the fact that this
is an OBP alias set to '/virtual-devices/console'.  Instead we saw it
as the first serial console device, instead of the hypervisor console.

The infrastructure is now there to take advantage of this to resolve
the console correctly even in multi-head situations in fbcon too.

Thanks to Greg Onufer for the bug report.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Spelling fixes in arch/sparc64/.
Signed-off-by: NSimon Arlott <simon@fire.lp0.eu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove includes of <linux/smp_lock.h> where it is not used/needed.
Suggested by Al Viro.

Builds cleanly on x86_64, i386, alpha, ia64, powerpc, sparc,
sparc64, and arm (all 59 defconfigs).
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix atomicity of TIF update in flush_thread() for sparc64

Fixes correctly the race by using *_ti_thread_flag.

Race :

parent process executing :
sys_ptrace()
 (lock_kernel())
 (ptrace_get_task_struct(pid))
 arch_ptrace()
   ptrace_detach()
     ptrace_disable(child);
       clear_singlestep(child);
         clear_tsk_thread_flag(child, TIF_SINGLESTEP);
         (which clears the TIF_SINGLESTEP flag atomically from a different
          process)
 (put_task_struct(child))
 (unlock_kernel())

And at the same time, in the child process :
sys_execve()
 do_execve()
   search_binary_handler()
     load_elf_binary()
       flush_old_exec()
         flush_thread()
           doing a non-atomic thread flag update
Signed-off-by: NMathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJörn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: NAdrian Bunk <bunk@stusta.de>

We have to turn off the "polling nrflag" bit when we sleep
the cpu like this, so that we'll get a cross-cpu interrupt
to wake the processor up from the yield.

We also have to disable PSTATE_IE in %pstate around the yield
call and recheck need_resched() in order to avoid any races.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set, but never used.

We used to use this for dynamic IRQ retargetting, but that
code died a long time ago.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For 32 cpus and a slow console, it just wedges the
machine especially with DETECT_SOFTLOCKUP enabled.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When saving and restoing trap state, do the window spill/fill
handling inline so that we never trap deeper than 2 trap levels.
This is important for chips like Niagara.

The window fixup code is massively simplified, and many more
improvements are now possible.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This also cleans up tsb_context_switch().  The assembler
routine is now __tsb_context_switch() and the former is
an inline function that picks out the bits from the mm_struct
and passes it into the assembler code as arguments.

setup_tsb_parms() computes the locked TLB entry to map the
TSB.  Later when we support using the physical address quad
load instructions of Cheetah+ and later, we'll simply use
the physical address for the TSB register value and set
the map virtual and PTE both to zero.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We now use the TSB hardware assist features of the UltraSPARC
MMUs.

SMP is currently knowingly broken, we need to find another place
to store the per-cpu base pointers.  We hid them away in the TSB
base register, and that obviously will not work any more :-)

Another known broken case is non-8KB base page size.

Also noticed that flush_tlb_all() is not referenced anywhere, only
the internal __flush_tlb_all() (local cpu only) is used by the
sparc64 port, so we can get rid of flush_tlb_all().

The kernel gets it's own 8KB TSB (swapper_tsb) and each address space
gets it's own private 8K TSB.  Later we can add code to dynamically
increase the size of per-process TSB as the RSS grows.  An 8KB TSB is
good enough for up to about a 4MB RSS, after which the TSB starts to
incur many capacity and conflict misses.

We even accumulate OBP translations into the kernel TSB.

Another area for refinement is large page size support.  We could use
a secondary address space TSB to handle those.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Based upon a report and preliminary patch from Jim Gifford.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Make some changes to the NEED_RESCHED and POLLING_NRFLAG to reduce
confusion, and make their semantics rigid.  Improves efficiency of
resched_task and some cpu_idle routines.

* In resched_task:
- TIF_NEED_RESCHED is only cleared with the task's runqueue lock held,
  and as we hold it during resched_task, then there is no need for an
  atomic test and set there. The only other time this should be set is
  when the task's quantum expires, in the timer interrupt - this is
  protected against because the rq lock is irq-safe.

- If TIF_NEED_RESCHED is set, then we don't need to do anything. It
  won't get unset until the task get's schedule()d off.

- If we are running on the same CPU as the task we resched, then set
  TIF_NEED_RESCHED and no further action is required.

- If we are running on another CPU, and TIF_POLLING_NRFLAG is *not* set
  after TIF_NEED_RESCHED has been set, then we need to send an IPI.

Using these rules, we are able to remove the test and set operation in
resched_task, and make clear the previously vague semantics of
POLLING_NRFLAG.

* In idle routines:
- Enter cpu_idle with preempt disabled. When the need_resched() condition
  becomes true, explicitly call schedule(). This makes things a bit clearer
  (IMO), but haven't updated all architectures yet.

- Many do a test and clear of TIF_NEED_RESCHED for some reason. According
  to the resched_task rules, this isn't needed (and actually breaks the
  assumption that TIF_NEED_RESCHED is only cleared with the runqueue lock
  held). So remove that. Generally one less locked memory op when switching
  to the idle thread.

- Many idle routines clear TIF_POLLING_NRFLAG, and only set it in the inner
  most polling idle loops. The above resched_task semantics allow it to be
  set until before the last time need_resched() is checked before going into
  a halt requiring interrupt wakeup.

  Many idle routines simply never enter such a halt, and so POLLING_NRFLAG
  can be always left set, completely eliminating resched IPIs when rescheduling
  the idle task.

  POLLING_NRFLAG width can be increased, to reduce the chance of resched IPIs.
Signed-off-by: NNick Piggin <npiggin@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Con Kolivas <kernel@kolivas.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Run idle threads with preempt disabled.

Also corrected a bugs in arm26's cpu_idle (make it actually call schedule()).
How did it ever work before?

Might fix the CPU hotplugging hang which Nigel Cunningham noted.

We think the bug hits if the idle thread is preempted after checking
need_resched() and before going to sleep, then the CPU offlined.

After calling stop_machine_run, the CPU eventually returns from preemption and
into the idle thread and goes to sleep.  The CPU will continue executing
previous idle and have no chance to call play_dead.

By disabling preemption until we are ready to explicitly schedule, this bug is
fixed and the idle threads generally become more robust.

From: alexs <ashepard@u.washington.edu>

  PPC build fix

From: Yoichi Yuasa <yuasa@hh.iij4u.or.jp>

  MIPS build fix
Signed-off-by: NNick Piggin <npiggin@suse.de>
Signed-off-by: NYoichi Yuasa <yuasa@hh.iij4u.or.jp>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch (written by me and also containing many suggestions of Arjan van
de Ven) does a major cleanup of the spinlock code.  It does the following
things:

 - consolidates and enhances the spinlock/rwlock debugging code

 - simplifies the asm/spinlock.h files

 - encapsulates the raw spinlock type and moves generic spinlock
   features (such as ->break_lock) into the generic code.

 - cleans up the spinlock code hierarchy to get rid of the spaghetti.

Most notably there's now only a single variant of the debugging code,
located in lib/spinlock_debug.c.  (previously we had one SMP debugging
variant per architecture, plus a separate generic one for UP builds)

Also, i've enhanced the rwlock debugging facility, it will now track
write-owners.  There is new spinlock-owner/CPU-tracking on SMP builds too.
All locks have lockup detection now, which will work for both soft and hard
spin/rwlock lockups.

The arch-level include files now only contain the minimally necessary
subset of the spinlock code - all the rest that can be generalized now
lives in the generic headers:

 include/asm-i386/spinlock_types.h       |   16
 include/asm-x86_64/spinlock_types.h     |   16

I have also split up the various spinlock variants into separate files,
making it easier to see which does what. The new layout is:

   SMP                         |  UP
   ----------------------------|-----------------------------------
   asm/spinlock_types_smp.h    |  linux/spinlock_types_up.h
   linux/spinlock_types.h      |  linux/spinlock_types.h
   asm/spinlock_smp.h          |  linux/spinlock_up.h
   linux/spinlock_api_smp.h    |  linux/spinlock_api_up.h
   linux/spinlock.h            |  linux/spinlock.h

/*
 * here's the role of the various spinlock/rwlock related include files:
 *
 * on SMP builds:
 *
 *  asm/spinlock_types.h: contains the raw_spinlock_t/raw_rwlock_t and the
 *                        initializers
 *
 *  linux/spinlock_types.h:
 *                        defines the generic type and initializers
 *
 *  asm/spinlock.h:       contains the __raw_spin_*()/etc. lowlevel
 *                        implementations, mostly inline assembly code
 *
 *   (also included on UP-debug builds:)
 *
 *  linux/spinlock_api_smp.h:
 *                        contains the prototypes for the _spin_*() APIs.
 *
 *  linux/spinlock.h:     builds the final spin_*() APIs.
 *
 * on UP builds:
 *
 *  linux/spinlock_type_up.h:
 *                        contains the generic, simplified UP spinlock type.
 *                        (which is an empty structure on non-debug builds)
 *
 *  linux/spinlock_types.h:
 *                        defines the generic type and initializers
 *
 *  linux/spinlock_up.h:
 *                        contains the __raw_spin_*()/etc. version of UP
 *                        builds. (which are NOPs on non-debug, non-preempt
 *                        builds)
 *
 *   (included on UP-non-debug builds:)
 *
 *  linux/spinlock_api_up.h:
 *                        builds the _spin_*() APIs.
 *
 *  linux/spinlock.h:     builds the final spin_*() APIs.
 */

All SMP and UP architectures are converted by this patch.

arm, i386, ia64, ppc, ppc64, s390/s390x, x64 was build-tested via
crosscompilers.  m32r, mips, sh, sparc, have not been tested yet, but should
be mostly fine.

From: Grant Grundler <grundler@parisc-linux.org>

  Booted and lightly tested on a500-44 (64-bit, SMP kernel, dual CPU).
  Builds 32-bit SMP kernel (not booted or tested).  I did not try to build
  non-SMP kernels.  That should be trivial to fix up later if necessary.

  I converted bit ops atomic_hash lock to raw_spinlock_t.  Doing so avoids
  some ugly nesting of linux/*.h and asm/*.h files.  Those particular locks
  are well tested and contained entirely inside arch specific code.  I do NOT
  expect any new issues to arise with them.

 If someone does ever need to use debug/metrics with them, then they will
  need to unravel this hairball between spinlocks, atomic ops, and bit ops
  that exist only because parisc has exactly one atomic instruction: LDCW
  (load and clear word).

From: "Luck, Tony" <tony.luck@intel.com>

   ia64 fix
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NArjan van de Ven <arjanv@infradead.org>
Signed-off-by: NGrant Grundler <grundler@parisc-linux.org>
Cc: Matthew Wilcox <willy@debian.org>
Signed-off-by: NHirokazu Takata <takata@linux-m32r.org>
Signed-off-by: NMikael Pettersson <mikpe@csd.uu.se>
Signed-off-by: NBenoit Boissinot <benoit.boissinot@ens-lyon.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

It appears that a memory barrier soon after a mispredicted
branch, not just in the delay slot, can cause the hang
condition of this cpu errata.

So move them out-of-line, and explicitly put them into
a "branch always, predict taken" delay slot which should
fully kill this problem.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

machine_restart, machine_halt and machine_power_off are machine
specific hooks deep into the reboot logic, that modules
have no business messing with.  Usually code should be calling
kernel_restart, kernel_halt, kernel_power_off, or
emergency_restart. So don't export machine_restart,
machine_halt, and machine_power_off so we can catch buggy users.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

These two bits were accesses non-atomically from assembler
code.  So, in order to eliminate any potential races resulting
from that, move these pieces of state into two bytes elsewhere
in struct thread_info.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently sparc and sparc64's UP cpu_idle() checks current pid. This
is old time legacy. Now it's paranoia.
Signed-off-by: NCoywolf Qi Hunt <coywolf@lovecn.org>
Acked-by: NWilliam Irwin <wli@holomorphy.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!