On 32-bit mode only bits [31:0] of the CR should be used for setting the CR
value.  Otherwise, the host may incorrectly assume the value is invalid if bits
[63:32] are not zero.  Moreover, the CR is currently being read twice when CR8
is used.  Last, nested mov-cr exiting is modified to handle the CR value
correctly as well.
Signed-off-by: NNadav Amit <namit@cs.technion.ac.il>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Currently, the hypercall handling routine only considers LME as an indication
to whether the guest uses 32/64-bit mode. This is incosistent with hyperv
hypercalls handling and against the common sense of considering cs.l as well.
This patch uses is_64_bit_mode instead of is_long_mode for that matter. In
addition, the result is masked in respect to the guest execution mode. Last, it
changes kvm_hv_hypercall to use is_64_bit_mode as well to simplify the code.
Signed-off-by: NNadav Amit <namit@cs.technion.ac.il>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

When the guest sets DR6 and DR7, KVM asserts the high 32-bits are clear, and
otherwise injects a #GP exception. This exception should only be injected only
if running in long-mode.
Signed-off-by: NNadav Amit <namit@cs.technion.ac.il>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Many real CPUs get this wrong as well, but ours is totally off: bits 9:1
define the highest index value.
Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Allow L1 to "leak" its debug controls into L2, i.e. permit cleared
VM_{ENTRY_LOAD,EXIT_SAVE}_DEBUG_CONTROLS. This requires to manually
transfer the state of DR7 and IA32_DEBUGCTLMSR from L1 into L2 as both
run on different VMCS.
Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

SDM says bits 1, 4-6, 8, 13-16, and 26 have to be set.
Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

We already have this control enabled by exposing a broken
MSR_IA32_VMX_PROCBASED_CTLS value. This will properly advertise our
capability once the value is fixed by clearing the right bits in
MSR_IA32_VMX_TRUE_PROCBASED_CTLS. We also have to ensure to test the
right value on L2 entry.
Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

We already implemented them but failed to advertise them. Currently they
all return the identical values to the capability MSRs they are
augmenting. So there is no change in exposed features yet.

Drop related comments at this chance that are partially incorrect and
redundant anyway.
Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

The spec says those controls are at bit position 2 - makes 4 as value.

The impact of this mistake is effectively zero as we only use them to
ensure that these features are set at position 2 (or, previously, 1) in
MSR_IA32_VMX_{EXIT,ENTRY}_CTLS - which is and will be always true
according to the spec.
Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

On long-mode the current NOP (0x90) emulation still writes back to RAX.  As a
result, EAX is zero-extended and the high 32-bits of RAX are cleared.
Signed-off-by: NNadav Amit <namit@cs.technion.ac.il>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Even if the condition of cmov is not satisfied, bits[63:32] should be cleared.
This is clearly stated in Intel's CMOVcc documentation.  The solution is to
reassign the destination onto itself if the condition is unsatisfied.  For that
matter the original destination value needs to be read.
Signed-off-by: NNadav Amit <namit@cs.technion.ac.il>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Return unhandlable error on inter-privilege level ret instruction.  This is
since the current emulation does not check the privilege level correctly when
loading the CS, and does not pop RSP/SS as needed.

Cc: stable@vger.kernel.org
Signed-off-by: NNadav Amit <namit@cs.technion.ac.il>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

The emulator does not emulate the xadd instruction correctly if the two
operands are the same.  In this (unlikely) situation the result should be the
sum of X and X (2X) when it is currently X.  The solution is to first perform
writeback to the source, before writing to the destination.  The only
instruction which should be affected is xadd, as the other instructions that
perform writeback to the source use the extended accumlator (e.g., RAX:RDX).
Signed-off-by: NNadav Amit <namit@cs.technion.ac.il>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

The current emulation of bit operations ignores the offset from the destination
on 64-bit target memory operands. This patch fixes this behavior.
Signed-off-by: NNadav Amit <namit@cs.technion.ac.il>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

use mm.h definition

Cc: Gleb Natapov <gleb@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: NFabian Frederick <fabf@skynet.be>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

It was using the wrong member of the union.
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Memory is always the destination for BitOp instructions.
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

We did not do that when interruptibility was added to the emulator,
because at the time pop to segment was not implemented.  Now it is,
add it.
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

In 64-bit mode, when the destination is a register, the assignment is done
according to the operand size. Otherwise (memory operand or no 64-bit mode), a
16-bit assignment is performed.

Currently, 16-bit assignment is always done to the destination.
Signed-off-by: NNadav Amit <namit@cs.technion.ac.il>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

cmpxchg16b is currently unimplemented in the emulator. The least we can do is
return error upon the emulation of this instruction.
Signed-off-by: NNadav Amit <namit@cs.technion.ac.il>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

The rdpmc emulation checks that the counter (ECX) is not higher than 2, without
taking into considerations bits 30:31 role (e.g., bit 30 marks whether the
counter is fixed). The fix uses the pmu information for checking the validity
of the pmu counter.
Signed-off-by: NNadav Amit <namit@cs.technion.ac.il>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

If the operand-size prefix (0x66) is used in 64-bit mode, the emulator would
assume the destination operand is 64-bit, when it should be 32-bit.

Reminder: movnti does not support 16-bit operands and its default operand size
is 32-bit.
Signed-off-by: NNadav Amit <namit@cs.technion.ac.il>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

The current implementation of cmpxchg does not update the flags correctly,
since the accumulator should be compared with the destination and not the other
way around. The current implementation does not update the flags correctly.
Signed-off-by: NNadav Amit <namit@cs.technion.ac.il>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

The SGDT and SIDT instructions are not privilaged, i.e. they can be executed
with CPL>0.
Signed-off-by: NNadav Amit <namit@cs.technion.ac.il>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

The current emulator implementation ignores the high 32 bits of the base in
long-mode.  During segment load from the LDT, the base of the LDT is calculated
incorrectly and may cause the wrong segment to be loaded.
Signed-off-by: NNadav Amit <namit@cs.technion.ac.il>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

The current implementation ignores the LDTR/TR base high 32-bits on long-mode.
As a result the loaded segment descriptor may be incorrect.
Signed-off-by: NNadav Amit <namit@cs.technion.ac.il>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Currently the emulator does not recognize vex-prefix instructions.  However, it
may incorrectly decode lgdt/lidt instructions and try to execute them. This
patch returns unhandlable error on their emulation.
Signed-off-by: NNadav Amit <namit@cs.technion.ac.il>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Pull networking fixes from David Miller:

 1) Fix checksumming regressions, from Tom Herbert.

 2) Undo unintentional permissions changes for SCTP rto_alpha and
    rto_beta sysfs knobs, from Denial Borkmann.

 3) VXLAN, like other IP tunnels, should advertize it's encapsulation
    size using dev->needed_headroom instead of dev->hard_header_len.
    From Cong Wang.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  net: sctp: fix permissions for rto_alpha and rto_beta knobs
  vxlan: Checksum fixes
  net: add skb_pop_rcv_encapsulation
  udp: call __skb_checksum_complete when doing full checksum
  net: Fix save software checksum complete
  net: Fix GSO constants to match NETIF flags
  udp: ipv4: do not waste time in __udp4_lib_mcast_demux_lookup
  vxlan: use dev->needed_headroom instead of dev->hard_header_len
  MAINTAINERS: update cxgb4 maintainer

Pull more clock framework updates from Mike Turquette:
 "This contains the second half the of the clk changes for 3.16.

  They are simply fixes and code refactoring for the OMAP clock drivers.
  The sunxi clock driver changes include splitting out the one
  mega-driver into several smaller pieces and adding support for the A31
  SoC clocks"

* tag 'clk-for-linus-3.16-part2' of git://git.linaro.org/people/mike.turquette/linux: (25 commits)
  clk: sunxi: document PRCM clock compatible strings
  clk: sunxi: add PRCM (Power/Reset/Clock Management) clks support
  clk: sun6i: Protect SDRAM gating bit
  clk: sun6i: Protect CPU clock
  clk: sunxi: Rework clock protection code
  clk: sunxi: Move the GMAC clock to a file of its own
  clk: sunxi: Move the 24M oscillator to a file of its own
  clk: sunxi: Remove calls to clk_put
  clk: sunxi: document new A31 USB clock compatible
  clk: sunxi: Implement A31 USB clock
  ARM: dts: OMAP5/DRA7: use omap5-mpu-dpll-clock capable of dealing with higher frequencies
  CLK: TI: dpll: support OMAP5 MPU DPLL that need special handling for higher frequencies
  ARM: OMAP5+: dpll: support Duty Cycle Correction(DCC)
  CLK: TI: clk-54xx: Set the rate for dpll_abe_m2x2_ck
  CLK: TI: Driver for DRA7 ATL (Audio Tracking Logic)
  dt:/bindings: DRA7 ATL (Audio Tracking Logic) clock bindings
  ARM: dts: dra7xx-clocks: Correct name for atl clkin3 clock
  CLK: TI: gate: add composite interface clock to OMAP2 only build
  ARM: OMAP2: clock: add DT boot support for cpufreq_ck
  CLK: TI: OMAP2: add clock init support
  ...

Pull NVMe update from Matthew Wilcox:
 "Mostly bugfixes again for the NVMe driver.  I'd like to call out the
  exported tracepoint in the block layer; I believe Keith has cleared
  this with Jens.

  We've had a few reports from people who're really pounding on NVMe
  devices at scale, hence the timeout changes (and new module
  parameters), hotplug cpu deadlock, tracepoints, and minor performance
  tweaks"

[ Jens hadn't seen that tracepoint thing, but is ok with it - it will
  end up going away when mq conversion happens ]

* git://git.infradead.org/users/willy/linux-nvme: (22 commits)
  NVMe: Fix START_STOP_UNIT Scsi->NVMe translation.
  NVMe: Use Log Page constants in SCSI emulation
  NVMe: Define Log Page constants
  NVMe: Fix hot cpu notification dead lock
  NVMe: Rename io_timeout to nvme_io_timeout
  NVMe: Use last bytes of f/w rev SCSI Inquiry
  NVMe: Adhere to request queue block accounting enable/disable
  NVMe: Fix nvme get/put queue semantics
  NVMe: Delete NVME_GET_FEAT_TEMP_THRESH
  NVMe: Make admin timeout a module parameter
  NVMe: Make iod bio timeout a parameter
  NVMe: Prevent possible NULL pointer dereference
  NVMe: Fix the buffer size passed in GetLogPage(CDW10.NUMD)
  NVMe: Update data structures for NVMe 1.2
  NVMe: Enable BUILD_BUG_ON checks
  NVMe: Update namespace and controller identify structures to the 1.1a spec
  NVMe: Flush with data support
  NVMe: Configure support for block flush
  NVMe: Add tracepoints
  NVMe: Protect against badly formatted CQEs
  ...

Commit 3fd091e7 ("[SCTP]: Remove multiple levels of msecs
to jiffies conversions.") has silently changed permissions for
rto_alpha and rto_beta knobs from 0644 to 0444. The purpose of
this was to discourage users from tweaking rto_alpha and
rto_beta knobs in production environments since they are key
to correctly compute rtt/srtt.

RFC4960 under section 6.3.1. RTO Calculation says regarding
rto_alpha and rto_beta under rule C3 and C4:

  [...]
  C3)  When a new RTT measurement R' is made, set

       RTTVAR <- (1 - RTO.Beta) * RTTVAR + RTO.Beta * |SRTT - R'|

       and

       SRTT <- (1 - RTO.Alpha) * SRTT + RTO.Alpha * R'

       Note: The value of SRTT used in the update to RTTVAR
       is its value before updating SRTT itself using the
       second assignment. After the computation, update
       RTO <- SRTT + 4 * RTTVAR.

  C4)  When data is in flight and when allowed by rule C5
       below, a new RTT measurement MUST be made each round
       trip. Furthermore, new RTT measurements SHOULD be
       made no more than once per round trip for a given
       destination transport address. There are two reasons
       for this recommendation: First, it appears that
       measuring more frequently often does not in practice
       yield any significant benefit [ALLMAN99]; second,
       if measurements are made more often, then the values
       of RTO.Alpha and RTO.Beta in rule C3 above should be
       adjusted so that SRTT and RTTVAR still adjust to
       changes at roughly the same rate (in terms of how many
       round trips it takes them to reflect new values) as
       they would if making only one measurement per
       round-trip and using RTO.Alpha and RTO.Beta as given
       in rule C3. However, the exact nature of these
       adjustments remains a research issue.
  [...]

While it is discouraged to adjust rto_alpha and rto_beta
and not further specified how to adjust them, the RFC also
doesn't explicitly forbid it, but rather gives a RECOMMENDED
default value (rto_alpha=3, rto_beta=2). We have a couple
of users relying on the old permissions before they got
changed. That said, if someone really has the urge to adjust
them, we could allow it with a warning in the log.

Fixes: 3fd091e7 ("[SCTP]: Remove multiple levels of msecs to jiffies conversions.")
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tom Herbert says:

====================
Fixes related to some recent checksum modifications.

- Fix GSO constants to match NETIF flags
- Fix logic in saving checksum complete in __skb_checksum_complete
- Call __skb_checksum_complete from UDP if we are checksumming over
  whole packet in order to save checksum.
- Fixes to VXLAN to work correctly with checksum complete
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Call skb_pop_rcv_encapsulation and postpull_rcsum for the Ethernet
header to work properly with checksum complete.
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This function is used by UDP encapsulation protocols in RX when
crossing encapsulation boundary. If ip_summed is set to
CHECKSUM_UNNECESSARY and encapsulation is not set, change to
CHECKSUM_NONE since the checksum has not been validated within the
encapsulation. Clears csum_valid by the same rationale.
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In __udp_lib_checksum_complete check if checksum is being done over all
the data (len is equal to skb->len) and if it is call
__skb_checksum_complete instead of __skb_checksum_complete_head. This
allows checksum to be saved in checksum complete.
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Geert reported issues regarding checksum complete and UDP.
The logic introduced in commit 7e3cead5
("net: Save software checksum complete") is not correct.

This patch:
1) Restores code in __skb_checksum_complete_header except for setting
   CHECKSUM_UNNECESSARY. This function may be calculating checksum on
   something less than skb->len.
2) Adds saving checksum to __skb_checksum_complete. The full packet
   checksum 0..skb->len is calculated without adding in pseudo header.
   This value is saved in skb->csum and then the pseudo header is added
   to that to derive the checksum for validation.
3) In both __skb_checksum_complete_header and __skb_checksum_complete,
   set skb->csum_valid to whether checksum of zero was computed. This
   allows skb_csum_unnecessary to return true without changing to
   CHECKSUM_UNNECESSARY which was done previously.
4) Copy new csum related bits in __copy_skb_header.
Reported-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Joseph Gasparakis reported that VXLAN GSO offload stopped working with
i40e device after recent UDP changes. The problem is that the
SKB_GSO_* bits are out of sync with the corresponding NETIF flags. This
patch fixes that. Also, we add BUILD_BUG_ONs in net_gso_ok for several
GSO constants that were missing to avoid the problem in the future.
Reported-by: NJoseph Gasparakis <joseph.gasparakis@intel.com>
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull more SCSI updates from James Bottomley:
 "This is just a couple of drivers (hpsa and lpfc) that got left out for
  further testing in linux-next.  We also have one fix to a prior
  submission (qla2xxx sparse)"

* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (36 commits)
  qla2xxx: fix sparse warnings introduced by previous target mode t10-dif patch
  lpfc: Update lpfc version to driver version 10.2.8001.0
  lpfc: Fix ExpressLane priority setup
  lpfc: mark old devices as obsolete
  lpfc: Fix for initializing RRQ bitmap
  lpfc: Fix for cleaning up stale ring flag and sp_queue_event entries
  lpfc: Update lpfc version to driver version 10.2.8000.0
  lpfc: Update Copyright on changed files from 8.3.45 patches
  lpfc: Update Copyright on changed files
  lpfc: Fixed locking for scsi task management commands
  lpfc: Convert runtime references to old xlane cfg param to fof cfg param
  lpfc: Fix FW dump using sysfs
  lpfc: Fix SLI4 s abort loop to process all FCP rings and under ring_lock
  lpfc: Fixed kernel panic in lpfc_abort_handler
  lpfc: Fix locking for postbufq when freeing
  lpfc: Fix locking for lpfc_hba_down_post
  lpfc: Fix dynamic transitions of FirstBurst from on to off
  hpsa: fix handling of hpsa_volume_offline return value
  hpsa: return -ENOMEM not -1 on kzalloc failure in hpsa_get_device_id
  hpsa: remove messages about volume status VPD inquiry page not supported
  ...

Pull more btrfs updates from Chris Mason:
 "This has a few fixes since our last pull and a new ioctl for doing
  btree searches from userland.  It's very similar to the existing
  ioctl, but lets us return larger items back down to the app"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  btrfs: fix error handling in create_pending_snapshot
  btrfs: fix use of uninit "ret" in end_extent_writepage()
  btrfs: free ulist in qgroup_shared_accounting() error path
  Btrfs: fix qgroups sanity test crash or hang
  btrfs: prevent RCU warning when dereferencing radix tree slot
  Btrfs: fix unfinished readahead thread for raid5/6 degraded mounting
  btrfs: new ioctl TREE_SEARCH_V2
  btrfs: tree_search, search_ioctl: direct copy to userspace
  btrfs: new function read_extent_buffer_to_user
  btrfs: tree_search, copy_to_sk: return needed size on EOVERFLOW
  btrfs: tree_search, copy_to_sk: return EOVERFLOW for too small buffer
  btrfs: tree_search, search_ioctl: accept varying buffer
  btrfs: tree_search: eliminate redundant nr_items check