Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 18 5月, 2011 5 次提交
    • A
      EHCI: don't rescan interrupt QHs needlessly · 1e12c910
      由 Alan Stern 提交于 
      This patch (as1466) speeds up processing of ehci-hcd's periodic list.
The existing code will pointlessly rescan an interrupt endpoint queue
each time it encounters the queue's QH in the periodic list, which can
happen quite a few times if the endpoint's period is low.  On some
embedded systems, this useless overhead can waste so much time that
the driver falls hopelessly behind and loses events.

The patch introduces a "periodic_stamp" variable, which gets
incremented each time scan_periodic() runs and each time the scan
advances to a new frame.  If the corresponding stamp in an interrupt
QH is equal to the current periodic_stamp, we assume the QH has
already been scanned and skip over it.  Otherwise we scan the QH as
usual, and if none of its URBs have completed then we store the
current periodic_stamp in the QH's stamp, preventing it from being
scanned again.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      1e12c910
    • A
      OHCI: fix regression caused by nVidia shutdown workaround · 2b7aaf50
      由 Alan Stern 提交于 
      This patch (as1463) fixes a regression caused by commit
3df7169e (OHCI: work around for nVidia
shutdown problem).

The original problem encountered by people using NVIDIA chipsets was
that USB devices were not turning off when the system shut down.  For
example, the LED on an optical mouse would remain on, draining a
laptop's battery.  The problem was caused by a bug in the chipset; an
OHCI controller in the Reset state would continue to drive a bus reset
signal even after system shutdown.  The workaround was to put the
controllers into the Suspend state instead.

It turns out that later NVIDIA chipsets do not suffer from this bug.
Instead some have the opposite bug: If a system is shut down while an
OHCI controller is in the Suspend state, USB devices remain powered!
On other systems, shutting down with a Suspended controller causes the
system to reboot immediately.  Thus, working around the original bug
on some machines exposes other bugs on other machines.

The best solution seems to be to limit the workaround to OHCI
controllers with a low-numbered PCI product ID.  I don't know exactly
at what point NVIDIA changed their chipsets; the value used here is a
guess.  So far it was worked out okay for all the people who have
tested it.

This fixes Bugzilla #35032.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NAndre "Osku" Schmidt <andre.osku.schmidt@googlemail.com>
Tested-by: NYury Siamashka <yurand2@gmail.com>
CC: <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      2b7aaf50
    • M
      USB: OTG: msm: Free VCCCX regulator even if we can't set the voltage · e99c4309
      由 Mark Brown 提交于 
      If for some reason we fail to set the voltage range for the VDDCX regulator
when removing it's better to still disable and free the regulator as that
avoids leaking a reference to it and is likely to ensure that it's turned
off completely.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      e99c4309
    • M
      USB: OTG: msm: Allow the widest possible range for VDDCX when removing · 7b521fcb
      由 Mark Brown 提交于 
      When not active the hardware should be able to tolerate voltages within
the normal operating range so when removing set the maximum voltage we
can use to the maximum rather than minimum of the operating range. This
will improve interoperability in case we end up sharing the supply in
some design.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      7b521fcb
    • M
      USB: option: add support for Huawei E353 device · 610ba42f
      由 Marcin Gałczyński 提交于 
      I am sharing patch to the devices/usb/serial/option.c. This allows
operation of Huawei E353 broadband modem using the “option” driver. The
patch simply adds new constant with proper product ID and an entry to
usb_device_id. I worked on the 2.6.38.6 sources. Tested on Dell inspiron
1764 (i3 core cpu) and brand new Huawei E353 modem, Fedora 15 beta.

Looking at the type of change, i doubt it has potential to introduce
problems in other parts of kernel or the driver itself.
Signed-off-by: NMarcin Galczynski <marcin@galczynski.pl>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      610ba42f
  3. 17 5月, 2011 2 次提交
    • S
      xhci: Fix memory leak bug when dropping endpoints · 834cb0fc
      由 Sarah Sharp 提交于 
      When the USB core wants to change to an alternate interface setting that
doesn't include an active endpoint, or de-configuring the device, the xHCI
driver needs to issue a Configure Endpoint command to tell the host to
drop some endpoints from the schedule.  After the command completes, the
xHCI driver needs to free rings for any endpoints that were dropped.

Unfortunately, the xHCI driver wasn't actually freeing the endpoint rings
for dropped endpoints.  The rings would be freed if the endpoint's
information was simply changed (and a new ring was installed), but dropped
endpoints never had their rings freed.  This caused errors when the ring
segment DMA pool was freed when the xHCI driver was unloaded:

[ 5582.883995] xhci_hcd 0000:06:00.0: dma_pool_destroy xHCI ring segments, ffff88003371d000 busy
[ 5582.884002] xhci_hcd 0000:06:00.0: dma_pool_destroy xHCI ring segments, ffff880033716000 busy
[ 5582.884011] xhci_hcd 0000:06:00.0: dma_pool_destroy xHCI ring segments, ffff880033455000 busy
[ 5582.884018] xhci_hcd 0000:06:00.0: Freed segment pool
[ 5582.884026] xhci_hcd 0000:06:00.0: Freed device context pool
[ 5582.884033] xhci_hcd 0000:06:00.0: Freed small stream array pool
[ 5582.884038] xhci_hcd 0000:06:00.0: Freed medium stream array pool
[ 5582.884048] xhci_hcd 0000:06:00.0: xhci_stop completed - status = 1
[ 5582.884061] xhci_hcd 0000:06:00.0: USB bus 3 deregistered
[ 5582.884193] xhci_hcd 0000:06:00.0: PCI INT A disabled

Fix this issue and free endpoint rings when their endpoints are
successfully dropped.

This patch should be backported to kernels as old as 2.6.31.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
      834cb0fc
    • S
      xhci: Fix memory leak in ring cache deallocation. · 30f89ca0
      由 Sarah Sharp 提交于 
      When an endpoint ring is freed, it is either cached in a per-device ring
cache, or simply freed if the ring cache is full.  If the ring was added
to the cache, then virt_dev->num_rings_cached is incremented.  The cache
is designed to hold up to 31 endpoint rings, in array indexes 0 to 30.
When the device is freed (when the slot was disabled),
xhci_free_virt_device() is called, it would free the cached rings in
array indexes 0 to virt_dev->num_rings_cached.

Unfortunately, the original code in xhci_free_or_cache_endpoint_ring()
would put the first entry into the ring cache in array index 1, instead of
array index 0.  This was caused by the second assignment to rings_cached:

	rings_cached = virt_dev->num_rings_cached;
	if (rings_cached < XHCI_MAX_RINGS_CACHED) {
		virt_dev->num_rings_cached++;
		rings_cached = virt_dev->num_rings_cached;
		virt_dev->ring_cache[rings_cached] =
			virt_dev->eps[ep_index].ring;

This meant that when the device was freed, cached rings with indexes 0 to
N would be freed, and the last cached ring in index N+1 would not be
freed.  When the driver was unloaded, this caused interesting messages
like:

xhci_hcd 0000:06:00.0: dma_pool_destroy xHCI ring segments, ffff880063040000 busy

This should be queued to stable kernels back to 2.6.33.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
      30f89ca0
  5. 14 5月, 2011 9 次提交
  7. 13 5月, 2011 11 次提交
  9. 12 5月, 2011 4 次提交
    • S
      xhci: Fix bug in control transfer cancellation. · 3abeca99
      由 Sarah Sharp 提交于 
      When the xHCI driver attempts to cancel a transfer, it issues a Stop
Endpoint command and waits for the host controller to indicate which TRB
it was in the middle of processing.  The host will put an event TRB with
completion code COMP_STOP on the event ring if it stops on a control
transfer TRB (or other types of transfer TRBs).  The ring handling code
is supposed to set ep->stopped_trb to the TRB that the host stopped on
when this happens.

Unfortunately, there is a long-standing bug in the control transfer
completion code.  It doesn't actually check to see if COMP_STOP is set
before attempting to process the transfer based on which part of the
control TD completed.  So when we get an event on the data phase of the
control TRB with COMP_STOP set, it thinks it's a normal completion of
the transfer and doesn't set ep->stopped_td or ep->stopped_trb.

When the ring handling code goes on to process the completion of the Stop
Endpoint command, it sees that ep->stopped_trb is not a part of the TD
it's trying to cancel.  It thinks the hardware has its enqueue pointer
somewhere further up in the ring, and thinks it's safe to turn the control
TRBs into no-op TRBs.  Since the hardware was in the middle of the control
TRBs to be cancelled, the proper software behavior is to issue a Set TR
dequeue pointer command.

It turns out that the NEC host controllers can handle active TRBs being
set to no-op TRBs after a stop endpoint command, but other host
controllers have issues with this out-of-spec software behavior.  Fix this
behavior.

This patch should be backported to kernels as far back as 2.6.31, but it
may be a bit challenging, since process_ctrl_td() was introduced in some
refactoring done in 2.6.36, and some endian-safe patches added in 2.6.40
that touch the same lines.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: stable@kernel.org
      3abeca99
    • K
      usb: renesas_usbhs: fixup error processing on probe/remove · 97f93227
      由 Kuninori Morimoto 提交于 
      The error processing order was wrong.
This patch modify it.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      97f93227
    • K
      usb: renesas_usbhs: fixup fifo disable · c786e09c
      由 Kuninori Morimoto 提交于 
      It was necessary to check pipe condition after disable fifo.
Current driver checked it in a wrong place.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      c786e09c
    • E
      USB: cdc_acm: Fix oops when Droids MuIn LCD is connected · fd5054c1
      由 Erik Slagter 提交于 
      The Droids MuIn LCD operates like a serial remote terminal.
Data received are displayed directly on the LCD. This patch
fixes the kernel null pointer oops when it is plugged in.

Add NO_DATA_INTERFACE quirk to tell the driver that "control"
and "data" interfaces are not separated for this device, which
prevents dereferencing a null pointer in the device probe code.
Signed-off-by: NErik Slagter <erik@slagter.name>
Signed-off-by: NMaxin B. John <maxin.john@gmail.com>
Tested-by: NErik Slagter <erik@slagter.name>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      fd5054c1
  11. 11 5月, 2011 9 次提交