Convert all RGMII checks to use the phy_interface_mode_is_rgmii()
helper. This is a cosmetic patch.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds logic to reconfigure the comphy/GoP/MAC when the link
state is updated at runtime. This is very useful on boards where many
link speed are supported: depending on what is negotiated the PPv2
driver will automatically reconfigures the link between the PHY and the
MAC.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When using the XLG MAC, it does not make sense to force the GMAC autoneg
parameters. This patch adds checks to only set the GMAC autoneg
parameters when needed (i.e. when not using the XLG MAC).
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the link status changes, the phylib calls the link_event function
in the mvpp2 driver. Before this patch only the egress/ingress transmit
was enabled/disabled. This patch adds more functionality to the link
status management code by enabling/disabling the port per-cpu
interrupts, and the port itself. The queues are now stopped as well, and
the netif carrier helpers are called.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The link_event function is somewhat complicated. This cosmetic patch
simplifies it.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On some platforms, the comphy is between the MAC GoP and the PHYs. The
mvpp2 driver currently relies on the firmware/bootloader to configure
the comphy. As a comphy driver was added to the generic PHY framework,
this patch uses it in the mvpp2 driver to configure the comphy at boot
time to avoid relying on the bootloader.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MVPP22_XLG_CTRL1_FRAMESIZELIMIT define is used as an offset, but is
defined as BIT(0). Updated its name to contains "OFFS" as in offset and
fix its value using the offset value, 0.
Reported-by: NStefan Chulski <stefanc@marvell.com>
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Fixes: 76eb1b1d ("net: mvpp2: set maximum packet size for 10G ports")
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch uses the tso API to implement the tso functionality in Marvell
PPv2 driver.

Using iperf and 10G ports, using TSO shows a significant performance
improvement by a factor 2 to reach around 9.5Gbps in TX; as well as a
significant CPU usage drop (from 25% to 15%).
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The txq size is defined by MVPP2_AGGR_TXQ_SIZE, which is sometime not
used directly but through variables. As it is a fixed value use the
define everywhere in the driver.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch adds GoP (group of ports) initialization functions. The mvpp2
driver was relying on the firmware/bootloader initialization; this patch
moves this setup to the mvpp2 driver.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set maximum packet size for XLG 10G ports. Missing maximum packet size
for XLG configuration will cause kernel panic if oversized packet is
received by port.
Signed-off-by: NStefan Chulski <stefanc@marvell.com>
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds a routine to initialize the XLG MAC at the port level when
using a port and the XAUI/10GKR interface mode. This wasn't done until
this commit, and the mvpp2 driver was relying on the bootloader/firmware
initialization. This doesn't mean everything is configured in the mvpp2
driver now, but it helps reducing the gap.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds a routine to initialize the GMAC at the port level when using
a port. This wasn't done until this commit, and the mvpp2 driver was
relying on the bootloader/firmware initialization. This doesn't mean
everything is configured in the mvpp2 driver now, but it helps reducing
the gap.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This moves the mii configuration in the ndo_open path, to allow handling
different mii configurations later and to switch between these
configurations at runtime.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The macro defining the bit to toggle to bypass or not the
synchronization module is wrongly named. Writing 1 will disable bypass.
This patch s/MVPP22_CTRL4_SYNC_BYPASS/MVPP22_CTRL4_SYNC_BYPASS_DIS/.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cosmetic patch to use the same formatting rules on all register
definitions.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This commit adds the support for two related features:

 - Support for TX interrupts, with one interrupt for each CPU

 - Support for different RX queue distribution modes
   MVPP2_QDIST_SINGLE_MODE where a single interrupt, shared by all
   CPUs, receives the RX events, and MVPP2_QDIST_MULTI_MODE, where the
   per-CPU interrupts used for TX events are also used for RX events.

Since additional interrupts are needed, an update to the Device Tree
binding is needed. However, backward compatibility is preserved with
the old Device Tree binding, by gracefully degrading to the original
behavior, with only one RX interrupt, and TX completion being handled
by an hrtimer.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation to the introduction of TX interrupts and improved RX
queue distribution, this commit introduces the concept of "queue
vector". A queue vector represents a number of RX and/or TX queues,
and an associated NAPI instance and interrupt.

This commit currently only creates a single queue_vector, so there are
no changes in behavior, but it paves the way for additional
queue_vector in the next commits.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PPv2.2 IP has a concept of "software thread", with all registers
of the PPv2.2 mapped 8 times, for concurrent accesses by 8 "software
threads". In addition, interrupts on RX queues are associated to such
"software thread".

For most cases, we map a "software thread" to the more conventional
concept of CPU, but we will soon have one exception: we will have a
model where we have one TX interrupt per CPU (each using one software
thread), and all RX events mapped to another software thread
(associated to another interrupt).

In preparation for this change, it makes sense to change the naming
from MVPP2_MAX_CPUS to MVPP2_MAX_THREADS, and plan for 8 software
threads instead of 4 currently.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the global variables rxq_number and txq_number hold the
number of per-port TXQs and RXQs. Until now, such numbers were
constant regardless of the driver configuration. As we are going to
introduce different modes for TX and RX queues, these numbers will
depend on the configuration (PPv2.1 vs. PPv2.2, exact queue
distribution logic).

Therefore, as a preparation, we move the number of RXQs and TXQs in
the 'struct mvpp2_port' structure, next to the RXQs and TXQs
descriptor arrays.

For now, they remain initialized to the same default values as
rxq_number/txq_number used to be initialized, but this will change in
future commits.

The only non-mechanical change in this patch is that the check to
verify hardware constraints on the number of RXQs and TXQs is moved
from mvpp2_probe() to mvpp2_port_probe(), since it's now in
mvpp2_port_probe() that we initialize the per-port count of RXQ and
TXQ.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The RX queue group allocation is anyway re-done later in
mvpp2_port_init(), so resetting it in mvpp2_init() is not very useful,
and will be annoying as we are going to rework the RX queue group
allocation logic.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MVPP21_ISR_RXQ_GROUP_REG register is not indexed by rxq, but by
port, so we fix the parameter name accordingly. There are no
functional changes.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When all a function does is calling another function with the exact same
arguments, in the exact same order, you know it's time to remove said
function. Which is exactly what this commit does.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This function is not used in the driver, remove it.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A previous commit modified a number of smp_processor_id() used in
migration-enabled contexts into get_cpu/put_cpu sections. However, a few
smp_processor_id() calls remain in the driver, and this commit adds
comments explaining why they can be kept.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On GOP port 0 two MAC modes are available: GMAC and XLG. The XLG MAC is
used for 10G connectivity. This patch adds a basic 10G support by
allowing to use the XLG MAC on port 0 and by reworking the
port_enable/disable functions so that the XLG MAC is configured when
using 10G.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

smp_processor_id() should not be used in migration-enabled contexts. We
originally thought it was OK in the specific situation of this driver,
but it was wrong, and calling smp_processor_id() in a migration-enabled
context prints a big fat warning when CONFIG_DEBUG_PREEMPT=y.

Therefore, this commit replaces the smp_processor_id() in
migration-enabled contexts by the appropriate get_cpu/put_cpu sections.
Reported-by: NMarc Zyngier <marc.zyngier@arm.com>
Fixes: a786841d ("net: mvpp2: handle register mapping and access for PPv2.2")
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This commit removes the useless remove
mvpp2_bm_cookie_{build,pool_get} functions. All what
mvpp2_bm_cookie_build() was doing is compute a 32-bit value by
concatenating the pool number and the CPU number... only to get the pool
number re-extracted by mvpp2_bm_cookie_pool_get() later on.

Instead, just get the pool number directly from RX descriptor status,
and pass it to mvpp2_pool_refill() and mvpp2_rx_refill().

This has the added benefit of dropping a smp_processor_id() call in a
migration-enabled context, which is wrong, and is the original
motivation for making this change.

Fixes: 3f518509 ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mvpp22_port_mii_set() function was added by 26975821, but the
function directly returns without doing anything. This return was used
when debugging and wasn't removed before sending the patch. Fix this.

Fixes: 26975821 ("net: mvpp2: handle misc PPv2.1/PPv2.2 differences")
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The script "checkpatch.pl" pointed information out like the following.

Comparison to NULL could be written "txq->descs".

Thus fix the affected source code place.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adjust jump labels according to the Linux coding style convention.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adjust jump labels according to the Linux coding style convention.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adjust jump labels according to the Linux coding style convention.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adjust jump labels according to the Linux coding style convention.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the word "failed" in the string for three function calls.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adjust jump labels according to the Linux coding style convention.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The script "checkpatch.pl" pointed out that labels should not be indented.
Thus delete two horizontal tabs before the jump label "err_drop_frame"
in the function "mvpp2_rx".
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace the specification of two data structures by pointer dereferences
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace the specification of data structures by references to
a local variable as the parameter for the operator "sizeof"
to make the corresponding size determination a bit safer.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>