When adding an invalid LUN, there is a deadlock between the add
via scsi_scan_target and the slave_destroy handler: The handler
waits for the scan to complete, but for an invalid unit,
scsi_scan_target directly calls the slave_destroy handler.

Fix the deadlock by removing the wait in the slave_destroy
handler, it was not necessary anyway.
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NSwen Schillig <swen@vnet.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The common I/O layer can call remove a handler to inform zfcp
that a device disappeared. The handler zfcp_ccw_remove then
removes all unit, port and the adapter data structures. Removing
the units requires that the SCSI devices are removed first.
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NSwen Schillig <swen@vnet.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

It is not necessary to use jiffies or milliseconds to specify
waiting times that last a couple of seconds.
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NSwen Schillig <swen@vnet.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NSwen Schillig <swen@vnet.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The callback function used by zfcp always returns success,
which is an indication for the SCSI midlayer to stop error
handling. Remove the bus_reset callback, since the same
function will be called via the host_reset callback.
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NSwen Schillig <swen@vnet.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Some of our vendors have requested that our adapters ignore the hardware
reset attempts during recovery and have enforced this with changes in
Adapter Firmware. Some of our customers have requested the option to be
able to reset the adapter under adverse adapter failure, we even had a
few defects reported here considering it a regression that the Adapter
could not be reset. This patch addresses this dichotomy. The user can
force the adapter to be reset if it supports the IOP_RESET_ALWAYS
command, in cases where the adapter has been programmed to ignore the
reset, by setting the aacraid.check_reset parameter to a value of -1.

The driver will not reset an Adapter that does not support the reset
command(s).

This patch also fixes and cleans up some of the logic associated with
resetting the adapter.
Signed-off-by: NMark Salyzyn <aacraid@adaptec.com>
Signed-off-by: NJames <James.Bottomley@HansenPartnership.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

  - This patch depends on:
      NCR5380: Use scsi_eh API for REQUEST_SENSE invocation
  - convert to accessors and !use_sg cleanup
  - FIXME: Not sg-chain ready look for ++cmd->SCp.buffer
Signed-off-by: NBoaz Harrosh <bharrosh@panasas.com>
Signed-off-by: NJames <James.Bottomley@HansenPartnership.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

  - code used to set sg_tablesize to zero for board revision
    less than 6. This is no longer supported, therefore I
    use sg_tablesize=1 and open code the sg handling for that case.
  - Get rid of use of SG_NONE which will be removed soon.
Signed-off-by: NBoaz Harrosh <bharrosh@panasas.com>
Signed-off-by: NJames <James.Bottomley@HansenPartnership.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

 - convert to accessors and !use_sg cleanup
 - Probably not ready for sg-chaining
Signed-off-by: NBoaz Harrosh <bharrosh@panasas.com>
Acked-by: NChristoph Hellwig <hch@infradead.org>
Cc: jameshsu <jameshsu@acard.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

  - remove the unnecessary map_single path.
  - convert to use the new accessors for the sg lists and the
    parameters.
Signed-off-by: NBoaz Harrosh <bharrosh@panasas.com>
Acked-by: NDouglas Gilbert <dougg@torque.net>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

  - This patch should be commited before:
    usb: transport - convert to accessors and !use_sg code path removal

  - isd200_action() was still using direct liniar pointers in issuing
    commands to the USB transport level. This is no longer supported,
    use one-element scatterlist instead.
  - Adjustment of command's length in the case of scsi-to-ata translation
    is now restored before return to queuecommand, since other wise it can
    leak BIOs.
  - isd200_action() return Error on unknown requests. Used to print an error
    but still try to send garbage cdb.
  - convert few places to scsi data accessors.
  - Todo: This file will need to be changed when scsi_cmnd changes to
    scsi_data_buffer or any other solution.
Signed-off-by: NBoaz Harrosh <bharrosh@panasas.com>
Acked-by: NMatthew Dharm <mdharm-scsi@one-eyed-alien.net>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

  - This patch depends on:
    usb: transport.c use scsi_eh API in REQUEST_SENSE execution

  - Use scsi data accessors and remove of !use_sg code path.
  - New usb_stor_bulk_srb() for use by drivers

[jejb: updated with corrective fix.

had a bug in residual handling in the new usb_stor_bulk_srb()
function.  Found by Gabriel C. in -mm tree.
Tested-by: NGabriel C <nix.or.die@googlemail.com>
]
Signed-off-by: NBoaz Harrosh <bharrosh@panasas.com>
Acked-by: NMatthew Dharm <mdharm-scsi@one-eyed-alien.net>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

 - functions that received char* but where passed scatterlist* mostly
   were changed to receive void*
 - Use scsi data accessors and remove of !use_sg code path
Signed-off-by: NBoaz Harrosh <bharrosh@panasas.com>
Acked-by: NMatthew Dharm <mdharm-scsi@one-eyed-alien.net>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

 - Use scsi data accessors and remove of !use_sg code path
 - This patch is dependent on cleanup patch to usb transport.c/h
Signed-off-by: NBoaz Harrosh <bharrosh@panasas.com>
Acked-by: NMatthew Dharm <mdharm-scsi@one-eyed-alien.net>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

 - Use scsi data accessors and remove of !use_sg code path
Signed-off-by: NBoaz Harrosh <bharrosh@panasas.com>
Acked-by: NMatthew Dharm <mdharm-scsi@one-eyed-alien.net>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

  - Apparently no one wonts this driver, and no one
    is willing to fix it for future changes to SCSI.
    So remove it, and if someone wants it in the future
    He can revive it with the needed fixes.
Signed-off-by: NBoaz Harrosh <bharrosh@panasas.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The psi240i driver is still written for cmnd->request_buffer
as a char pointer to actual data. There was never any attempt
to use the scatterlist option.

  - remove all source files (3) from drivers/scsi
  - Remove from Makefile and Kconfig
Signed-off-by: NBoaz Harrosh <bharrosh@panasas.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

 - convert to accessors and !use_sg cleanup
Signed-off-by: NBoaz Harrosh <bharrosh@panasas.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

 - convert to accessors and !use_sg cleanup
Signed-off-by: NBoaz Harrosh <bharrosh@panasas.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

 - convert to accessors and !use_sg cleanup
Signed-off-by: NBoaz Harrosh <bharrosh@panasas.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

 - convert to accessors and !use_sg cleanup
 - Not ready for sg-chaining
Signed-off-by: NBoaz Harrosh <bharrosh@panasas.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

 - convert to accessors and !use_sg cleanup
Signed-off-by: NBoaz Harrosh <bharrosh@panasas.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

 - convert to accessors and !use_sg cleanup
Signed-off-by: NBoaz Harrosh <bharrosh@panasas.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

 - convert to accessors and !use_sg cleanup
Signed-off-by: NBoaz Harrosh <bharrosh@panasas.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

 - convert to accessors and !use_sg cleanup
Signed-off-by: NBoaz Harrosh <bharrosh@panasas.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

  - use scsi data accessors
  - cleanup !use_sg code paths
  - TODO: use next_sg() for Jens's sglist branch. Look for 2
    places with "SCp.buffer++"
Signed-off-by: NBoaz Harrosh <bharrosh@panasas.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

  - Use new scsi_eh_prep/restor_cmnd() for synchronous
    REQUEST_SENSE invocation.
Signed-off-by: NBoaz Harrosh <bharrosh@panasas.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

I was working on patches which add new transport error values, when I
noticed that DID_REQUEUE was not in the hostbyte_table. I do not think
there is any way to hit the code path where scsi_show_result is called
and where you return DID_REQUEUE, because DID_REQUEUE causes scsi-ml to
always requeue the command. However, for completeness and because I want
to one day send a patch that tries to add new host bytes values, I am
sending this patch.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Change version number to 8.2.3
Signed-off-by: NJames Smart <James.Smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Temperature handling fix - return proper error code indicator for applications
Signed-off-by: NJames Smart <James.Smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Internal loopback fixes:
- Use HBQs rather than Q_RING_BUFF
- Correct HBQs continuation entries
- Update CT handler to SLI3 iocbs
Signed-off-by: NJames Smart <James.Smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Miscellaneous Small Fixes - part 2

- Fix ndlp left in PLOGI state after link up
- Fix cannot rcv unsol ELS frames after running HBA resets for a few minutes
- Fix HBQ buffer_count implemention
- Fix RPI leak
- Fix crash while deleting vports while HBA is reset
- Revert the FCP Fbits offset back to 7
- Fix panic when deleting vports
- Remove unused code in switch statement outside of a case
- Reject PLOGI from invalid PName or NName of 0
- Ignore PLOGI responses from WWPName or WWNName of 0
- Fix debugfs hbqinfo display for ppc
- Added 8G to list of supported speeds for sysfs parameter
- Defer ndlp cleanup to dev-loss timeout handler
- Added support for WRITE_VPARMS mailbox command by applications
Signed-off-by: NJames Smart <James.Smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

FC Discovery Fixes:
- Fix up lpfc_drop_node() vs lpfc_nlp_not_used() usage
- Clear ADISC flag when unregistering RPI and REMOVE ndlps if in recovery.
- Fix usage of UNUSED list and ndlps
- Fix PLOGI race conditions
- Reset link if NameServer PLOGI errors occur
- Synchronize GID_FT queries with PLOGI receptions
Signed-off-by: NJames Smart <James.Smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Miscellaneous Small Fixes - part 1
- Fix typo kmzlloc -> kzalloc
- Fix discovery ndlp use after free panic
- Fix link event causing flood of 0108 messages
- Relieve some mbox congestion on link up with 100 vports
- Fix broken vport parameters
- Prevent lock recursion in logo_reglogin_issue
- Split uses of error variable in lpfc_pci_probe_one into retval and error
- Remove completion code related to dev_loss_tmo
- Remove unused LPFC_MAX_HBQ #define
- Don't compare pointers to 0 for sparse
- Make 2 functions static for sparse
- Fix default rpi cleanup code causing rogue ndlps to remain on the NPR list
- Remove annoying ELS messages when driver is unloaded
- Fix Cannot issue Register Fabric login problems on link up
- Remove LPFC_EVT_DEV_LOSS_DELAY
- Fix FC port swap test leads to device going offline
- Fix vport CT flags to only be set when accepted
- Add code to handle signals during vport_create
- Fix too many retries in FC-AL mode
- Pull lpfc_port_link_failure out of lpfc_linkdown_port
Signed-off-by: NJames Smart <James.Smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Remove flawed MBX_STOP_IOCB logic
Signed-off-by: NJames Smart <James.Smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

NPIV bug fixes:
- Remove vport params on physical hba when npiv is disabled
- Implement new DA_ID CT command to remove vport information from
  the switch after delete. Some switches didn't clean this up unless
  the physical link dropped.
Signed-off-by: NJames Smart <James.Smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Added support for ASICs that report temperature. Temperature notices are
 reported as events and logged. Temperature can be read via sysfs.
Signed-off-by: NJames Smart <James.Smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Set the default command timeout for ibmvscsi disks to 60 seconds
to ensure we don't prematurely timeout commands. This fixes a problem
seen where the default 30 seconds was not long enough due to
congestion on the server.
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

This patch does some additional cleanups after the 53c7xx removal.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

- convert to use the new accessors for the sg lists and the
parameters.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>