Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 16 6月, 2009 4 次提交
    • D
      musb: make initial HNP roleswitch work (v2) · 1de00dae
      由 David Brownell 提交于 
      Minor HNP bugfixes, so the initial role switch works:

 - A-Device:
     * disconnect-during-suspend enters A_PERIPHERAL state
     * kill OTG timer after reset as A_PERIPHERAL ...
     * ... and also pass that reset to the gadget
     * once HNP succeeds, clear the "ignore_disconnect" flag
     * from A_PERIPHERAL, disconnect transitions to A_WAIT_BCON

 - B-Device:
     * kill OTG timer on entry to B_HOST state (HNP succeeded)
     * once HNP succeeds, clear "ignore_disconnect" flag
     * kick the root hub only _after_ the state is adjusted

Other state transitions are left alone.  Notably, exit paths from
the "roles have switched" state ... A_PERIPHERAL handling of that
stays seriously broken.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      1de00dae
    • D
      musb: otg timer cleanup · f7f9d63e
      由 David Brownell 提交于 
      Minor cleanup of OTG timer handling:
    * unify decls for OTG time constants, in the core header
    * set up and use that timer in a more normal way
    * move to the driver struct, so it's usable outside core

And tighten use and setup of T(a_wait_bcon) so that if it's used,
it's always valid.  (If that timer expires, the A-device will
stop powering VBUS.  For non-OTG systems, that will be a surprise.)
No behavioral changes, other than more consistency when applying
that core HNP timeout.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      f7f9d63e
    • D
      musb: proper hookup to transceiver drivers · 84e250ff
      由 David Brownell 提交于 
      Let the otg_transceiver in MUSB be managed by an external driver;
don't assume it's integrated.  OMAP3 chips need it to be external,
and there may be ways to interact with the transceiver which add
functionality to the system.

Platform init code is responsible for setting up the transeciver,
probably using the NOP transceiver for integrated transceivers.
External ones will use whatever the board init code provided,
such as twl4030 or something more hands-off.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      84e250ff
    • S
      musb_gadget: fix unhandled endpoint 0 IRQs · a5073b52
      由 Sergei Shtylyov 提交于 
      The gadget EP0 code routinely ignores an interrupt at end of
the data phase because of musb_g_ep0_giveback() resetting the
state machine to "idle, waiting for SETUP" phase prematurely.

The driver also prematurely leaves the status phase on
receiving the SetupEnd interrupt.

As there were still unhandled endpoint 0 interrupts happening
from time to time after fixing these issues, there turned to
be yet another culprit: two distinct gadget states collapsed
into one.

The (missing) state that comes after STATUS IN/OUT states was
typically indiscernible from them since the corresponding
interrupts tend to happen within too little period of time
(due to only a zero-length status packet in between) and so
they got coalesced; yet this state is not the same as the next
one which is associated with the reception of a SETUP packet.

Adding this extra state seems to have fixed the rest of the
unhandled interrupts that generic_interrupt() and
davinci_interrupt() hid by faking their result and only
emitting a debug message -- so, stop doing that.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      a5073b52
  3. 24 4月, 2009 1 次提交
  5. 18 4月, 2009 1 次提交
  7. 25 3月, 2009 1 次提交
    • A
      USB: musb: only turn off vbus in OTG hosts · 74382171
      由 Ajay Kumar Gupta 提交于 
      Except on DaVinci, VBUS is now switched off as part of idling the
USB link (after a_wait_bcon) whenever a device is disconnected
from host.  This is correct for OTG hosts, where either SRP or
an ID interrupt could turn VBUS on again.

However, for non-OTG hosts there's no way to turn VBUS on again,
so the host becomes unusable.  And the procfs entry which once
allowed a manual workaround for this is now gone.

This patch adds an is_otg_enabled() check before scheduling the
switch-off timer in disconnect path, supporting a "classic host"
mode where SRP is unavailable.

[ dbrownell@users.sourceforge.net: tweak patch description ]
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      74382171
  9. 28 2月, 2009 3 次提交
  11. 28 1月, 2009 1 次提交
  13. 08 1月, 2009 5 次提交
  15. 14 11月, 2008 1 次提交
  17. 18 10月, 2008 3 次提交
  19. 24 9月, 2008 1 次提交
  21. 22 8月, 2008 2 次提交
  23. 14 8月, 2008 2 次提交