Bart says: "can be done from user-space and is not especially interesting
even when debugging problems (raw PCI config space dump is far more useful)."
Signed-off-by: NAlexey Dobriyan <adobriyan@openvz.org>
Cc: Andrew Morton <akpm@osdl.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add "vlb_clock=" parameter for specifying VLB clock frequency (in MHz).

* Add "pci_clock=" parameter for specifying PCI bus clock frequency (in MHz).

While at it:

* qd65xx.c: rename {active,recovery}_cycle variables to {act,rec}_cyc.

Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Export ide_dma_exec_cmd() and __ide_dma_test_irq().

* Constify struct ide_dma_ops.

* Always set hwif->dma_ops to &sff_dma_ops in ide_setup_dma()
  (it is later overriden by ide_init_port() if needed) and drop
  'const struct ide_port_info *d' argument.

While at it:

* Rename __ide_dma_test_irq() to ide_dma_test_irq().
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add struct ide_dma_ops and convert core code + drivers to use it.

While at it:

* Drop "ide_" prefix from ->ide_dma_end and ->ide_dma_test_irq methods.

* Drop "ide_" "infixes" from DMA methods.

* au1xxx-ide.c:
  - use auide_dma_{test_irq,end}() directly in auide_dma_timeout()

* pdc202xx_old.c:
  - drop "old_" "infixes" from DMA methods

* siimage.c:
  - add siimage_dma_test_irq() helper
  - print SATA warning in siimage_init_one()

* Remove no longer needed ->init_hwif implementations.

v2:
* Changes based on review from Sergei:
  - s/siimage_ide_dma_test_irq/siimage_dma_test_irq/
  - s/drive->hwif/hwif/ in idefloppy_pc_intr().
  - fix patch description w.r.t. au1xxx-ide changes
  - fix au1xxx-ide build
  - fix naming for cmd64*_dma_ops
  - drop "ide_" and "old_" infixes
  - s/hpt3xxx_dma_ops/hpt37x_dma_ops/
  - s/hpt370x_dma_ops/hpt370_dma_ops/
  - use correct DMA ops for HPT302/N, HPT371/N and HPT374
  - s/it821x_smart_dma_ops/it821x_pass_through_dma_ops/

v3:
* Two bugs slipped in v2 (noticed by Sergei):
  - use correct DMA ops for HPT374 (for real this time)
  - handle HPT370/HPT370A properly
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Make ide_hwif_setup_dma() return an error value.

* Pass 'const struct ide_port_info *d' instead of 'unsigned long dmabase'
  to ->init_dma method and make it return an error value.

* Rename ide_get_or_set_dma_base() to ide_pci_dma_base(),
  change ordering of its arguments and then export it.

* Export ide_pci_set_master().

* Do complete DMA setup inside ->init_dma method and update ->init_dma
  users accordingly.

* Sanitize code for DMA setup in ide_init_port().

v2:
* Fix for CONFIG_BLK_DEV_IDEDMA_PCI=n configs
  (from Jiri Slaby <jirislaby@gmail.com>):

  Fix following compiler warning by returning EINVAL:

  In file included from ANYTHING-INCLUDING-IDE.H:45:
  include/linux/ide.h: In function ‘ide_hwif_setup_dma’:
  include/linux/ide.h:1022: warning: no return statement in function returning non-void

Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

There should be no functional changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Skip DMA initialization completely on revs < 0x20 by setting IDE_HFLAG_NO_DMA
host flag and resetting DMA host masks in alim15x3_init_one() (currently
ide_hwif_setup_dma() will try to obtain DMA base and setup PCI bus-mastering
but init_dma_ali15x3() will fail).
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Move hooks for port/host specific methods from ide_hwif_t to
  'struct ide_port_ops'.

* Add 'const struct ide_port_ops *port_ops' to 'struct ide_port_info'
  and ide_hwif_t.

* Update host drivers and core code accordingly.

While at it:

* Rename ata66_*() cable detect functions to *_cable_detect() to match
  the standard naming. (Suggested by Sergei Shtylyov)

v2:
* Fix build for bast-ide. (Noticed by Andrew Morton)
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

"bootable" should be the default behavior so replace
IDE_HFLAG_BOOTABLE host flag with IDE_HFLAG_NON_BOOTABLE.

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add ->cable_detect method to ide_hwif_t.

* Call the new method in ide_init_port() if:
  - the host supports UDMA modes > UDMA2 ('hwif->ultra_mask & 78')
  - DMA initialization was successful (if hwif->dma_base is not set
    ide_init_port() sets hwif->ultra_mask to zero)
  - "idex=ata66" is not used ('hwif->cbl != ATA_CBL_PATA40_SHORT')

* Convert PCI host drivers to use ->cable_detect method.

While at it:

* Factor out cable detection to separate functions (if not already done).

* hpt366.c/it8213.c/slc90e66.c:
  - don't check cable type if "idex=ata66" is used

* pdc202xx_new.c:
  - add __devinit tag to pdcnew_cable_detect()

* pdc202xx_old.c:
  - rename pdc202xx_old_cable_detect() to pdc2026x_old_cable_detect()
  - add __devinit tag to pdc2026x_old_cable_detect()
Reviewed-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Delete filenames/versions from comments.

I'm leaving decisions about adding DRV_VERSION defines and MODULE_VERSION()-s
to maintainers of the respective drivers.

While at it:

* Remove unused VERSION define from ide.c.

* Remove unused/stale DRV_VERSION define from au1xxx-ide.c.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Keep pointer to struct device instead of struct pci_dev in ide_hwif_t.

While on it:
* Use *dev->dma_mask instead of pci_dev->dma_mask in ide_toggle_bounce().

There should be no functionality changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Rename 'simplex_stat' variable to 'dma_stat' in ide_get_or_set_dma_base().

* Factor out code for forcing host out of "simplex" mode from
  ide_get_or_set_dma_base() to ide_pci_clear_simplex() helper.

* Add IDE_HFLAG_CLEAR_SIMPLEX host flag and set it in alim15x3 (for M5229),
  amd74xx (for AMD 7409), cmd64x (for CMD643), generic (for Netcell) and
  serverworks (for CSB5) host drivers.

* Make ide_get_or_set_dma_base() test for IDE_HFLAG_CLEAR_SIMPLEX host flag
  instead of checking dev->device (BTW the code was buggy because it didn't
  check for dev->vendor, luckily none of these PCI Device IDs was used by
  some other vendor for PCI IDE controller).
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

According to http://marc.info/?l=linux-ide&m=114346138611631, the drivers must
always register 8 DMA ports with ide_setup_dma(), so its last argument is not
needed. While at it, kill some useless parens in that function...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add IDE_HFLAG_ABUSE_SET_DMA_MODE host flag and use it to decide
  what to do with transfer modes < XFER_PIO_0 in ide_set_xfer_rate().

* Set IDE_HFLAG_ABUSE_SET_DMA_MODE in host drivers that need it
  (aec62xx, amd74xx, cs5520, cs5535, hpt34x, hpt366, pdc202xx_old,
  serverworks, tc86c001 and via82cxxx) and cleanup ->set_dma_mode
  methods in host drivers that don't (IDE core code guarantees that
  ->set_dma_mode will be called only for modes which are present
  in SWDMA/MWDMA/UDMA masks).

While at it:

* Add IDE_HFLAGS_HPT34X/HPT3XX/PDC202XX/SVWKS define in
  hpt34x/hpt366/pdc202xx_old/serverworks host driver.

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Port of Alan's patch for pata_ali.c.

Cc: Alan Cox <alan@redhat.com>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Rename struct ide_pci_device_s to struct ide_port_info.

* Remove ide_pci_device_t typedef.

While at it:

* Fix __ide_pci_register_driver() comment.

* Fix aec62xx_init_one() comment.

* Remove unused 'cds' field from ide_hwgroup_t.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Make a local copy of ali15x3_chipset in alim15x3_init_one() and set
  ->host_flags / ->udma_mask according to the controller capabilities.

* Cleanup init_hwif_common_ali15x3().

* Bump driver version.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Setup CD_ROM DMA and PIO FIFO settings in init_chipset_ali15x3() instead
  of ata66_ali15x3().  The latter is called from init_hwif_common_ali15x3()
  only if DMA base exists (which insists m5529_revision > 0x20).

  This changes makes CD_ROM DMA / PIO FIFO bits being set only once
  and also when "idex=ata66" kernel parameter is used.

* While at it move also chip_is_1543c_e setup from ata66_ali15x3() to
  init_chipset_ali15x3() and check if isa_dev exists before accessing it.

* Bump driver version.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Majority of host drivers using IDE PCI layer set drive->autotune, the only
exceptions are:

generic.c
ns87415.c
rz1000.c
trm290.c
* no ->set_pio_mode method

it821x.c:
* if memory allocation fails drive->autotune won't be set
  (but there also won't be ->set_pio_mode method in such case)

piix.c:
* MPIIX controller (no ->init_hwif method so also no ->set_pio_mode method)

However if there is no ->set_pio_mode method there are no changes in behavior
w.r.t. PIO tuning so always set drive->autotune in ide_pci_setup_ports().
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add ->mwdma_mask and ->swdma_mask to ide_pci_device_t.

* Set ide_hwif_t DMA masks using DMA masks from ide_pci_device_t in
  setup-pci.c::ide_pci_setup_ports() (iff DMA base is valid and ->init_hwif
  method may still override them).

* Convert IDE PCI host drivers to use ide_pci_device_t DMA masks.

While at it:

* Use ATA_{UDMA,MWDMA,SWDMA}* defines.

* hpt34x.c: add separate ide_pci_device_t instances for HPT343 and HPT345.

* serverworks.c: fix DMA masks being set before checking DMA base.

v2:
* Add missing masks to DECLARE_GENERIC_PCI_DEV() macro.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add IDE_HFLAG_NO_LBA48[_DMA] host flags, use it instead of hwif->no_lba48[_dma]
and then remove no longer needed hwif->no_lba48[_dma].  As a side-effect
this change fixes hwif->no_lba48_dma not being restored by ide_hwif_restore().
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add IDE_HFLAG_NO_{DMA,AUTODMA} host flags.  Convert all host drivers using
ide_pci_device_t to use these flags instead of d->autodma and then remove no
longer needed d->autodma.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add IDE_HFLAG_BOOTABLE host flag and IDE_HFLAG_OFF_BOARD define.  Convert
all host drivers using ide_pci_device_t to use IDE_HFLAG_{BOOTABLE,OFF_BOARD}
instead of d->bootable and then remove no longer needed d->bootable.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add IDE_HFLAG_NO_ATAPI_DMA host flag and set it in host drivers which
don't support ATAPI DMA.  Then remove no longer needed hwif->atapi_dma.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* hpt34x.c: disable DMA masks for HPT345
  (hwif->autodma is zero so DMA won't be enabled anyway).

* trm290.c: disable IDE_HFLAG_TRUST_BIOS_FOR_DMA flag
  (hwif->autodma is zero so DMA won't be enabled anyway).

* Check noautodma global variable instead of drive->autodma in ide_tune_dma().

  This fixes handling of "ide=nodma" kernel parameter for icside, ide-cris,
  au1xxx-ide, pmac, it821x, jmicron, sgiioc4 and siimage host drivers.

* Remove hwif->autodma (it was not checked by IDE core code anyway) and
  drive->autodma (was set by all host drivers - except HPT345/TRM290 special
  cases - unless "ide=nodma" was used).

While at it:
- remove needless printk() from icside.c
- remove stale FIXME/comment from ide-probe.c
- don't force DMA off if PCI bus-mastering had to be enabled in setup-pci.c
  (this setting was always later over-ridden by host drivers anyway)
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

While at it:
- make struct pci_device_id tables const
- use PCI_DEVICE_ID_ITE_8213 define in it8213.c
- fix comment in generic.c
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add IDE_HFLAG_TRUST_BIOS_FOR_DMA host flag for host drivers that depend
  on BIOS for programming device/controller for DMA.  Set it in cy82c693,
  generic, ns87415, opti621 and trm290 host drivers.

* Add IDE_HFLAG_VDMA host flag for host drivers using VDMA.  Set it in cs5520
  host driver.

* Teach ide_tune_dma() about IDE_HFLAG_TRUST_BIOS_FOR_DMA flag.

* Add generic ide_dma_check() helper and remove all open coded ->ide_dma_check
  implementations.  Fix all places checking for presence of ->ide_dma_check
  hook to check for ->ide_dma_on instead.

* Remove no longer needed code from config_drive_for_dma().

* Make ide_tune_dma() static.

v2:
* Fix config_drive_for_dma() return values.

* Fix ide-dma.c build for CONFIG_BLK_DEV_IDEDMA_PCI=n by adding
  dummy config_drive_for_dma() inline.

* Fix IDE_HFLAG_TRUST_BIOS_FOR_DMA handling in ide_dma_check().

* Fix init_hwif_it8213() comment.

There should be no functionality changes caused by this patch.

Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Several host drivers used to reset drive->init_speed in their ->ide_dma_check
implementations which resulted in incorrect init speed being reported to the
user, fix it.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

init_dma_ali15x3() guarantees that hwif->dma_base will never be set for
m5229_revision < 0x20 so remove redundant m5229_revision >= 0x20 check from
init_hwif_common_ali15x3().

While at it remove incorrect comment.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Convert {ide_hwif_t,ide_pci_device_t}->host_flag to be u16.

* Add IDE_HFLAG_POST_SET_MODE host flag to indicate the need to program 
  the host for the transfer mode after programming the device.  Set it
  in au1xxx-ide, amd74xx, cs5530, cs5535, pdc202xx_new, sc1200, pmac
  and via82cxxx host drivers.

* Add IDE_HFLAG_NO_SET_MODE host flag to indicate the need to completely
  skip programming of host/device for the transfer mode ("smart" hosts).
  Set it in it821x host driver and check it in ide_tune_dma().

* Add ide_set_pio_mode()/ide_set_dma_mode() helpers and convert all
  direct ->set_pio_mode/->speedproc users to use these helpers.

* Move ide_config_drive_speed() calls from ->set_pio_mode/->speedproc
  methods to callers.

* Rename ->speedproc method to ->set_dma_mode, make it void and update
  all implementations accordingly.

* Update ide_set_xfer_rate() comments.

* Unexport ide_config_drive_speed().

v2:
* Fix issues noticed by Sergei:
  - export ide_set_dma_mode() instead of moving ->set_pio_mode abuse wrt
    to setting DMA modes from sc1200_set_pio_mode() to do_special()
  - check IDE_HFLAG_NO_SET_MODE in ide_tune_dma()
  - check for (hwif->set_pio_mode) == NULL in ide_set_pio_mode()
  - check for (hwif->set_dma_mode) == NULL in ide_set_dma_mode()
  - return -1 from ide_set_{pio,dma}_mode() if ->set_{pio,dma}_mode == NULL
  - don't set ->set_{pio,dma}_mode on it821x in "smart" mode
  - fix build problem in pmac.c
  - minor fixes in au1xxx-ide.c/cs5530.c/siimage.c
  - improve patch description

Changes in behavior caused by this patch:
- HDIO_SET_PIO_MODE ioctl would now return -ENOSYS for attempts to change
  PIO mode if it821x controller is in "smart" mode
- removal of two debugging printk-s (from cs5530.c and sc1200.c)
- transfer modes 0x00-0x07 passed from user space may be programmed twice on
  the device (not really an issue since 0x00 is not supported correctly by
  any host driver ATM, 0x01 is not supported at all and 0x02-0x07 are invalid)
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Use ->set_pio_mode method to program PIO modes in ide_set_xfer_rate()
(the only place which used ->speedproc to program PIO modes) and remove
handling of PIO modes from all ->speedproc implementations.

v2:
* Fix pmac_ide_tune_chipset() comment.

There should be no functionality changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Return failure in ->speedproc method for unsupported/invalid transfer
  modes passed from user-space (fixes theoretical OOPS in ali_tune_pio()
  and/or setting random PIO timings on host controller + disabling UDMA
  bit + setting unsupported/invalid transfer mode on the device).

* Don't disable UDMA bit when programming PIO modes.

* Add FIXME about DMA timings never being set.

* Bump driver version.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add IDE_HFLAG_ABUSE_{PREFETCH,FAST_DEVSEL,DMA_MODES} flags
  and set them in ht6560, cmd640, cmd64x and sc1200 host drivers.

* Add set_pio_mode_abuse() for checking if host driver has a non-standard
  ->tuneproc() implementation and use it in do_special().

* Add ide_set_pio() for setting PIO mode (it uses hwif->pio_mask to find
  the maximum PIO mode supported by the host), also add ide_set_max_pio()
  wrapper for ide_set_pio() to use for auto-tuning.  Convert users of
  ->tuneproc to use ide_set{_max}_pio() where possible.  This leaves only
  do_special(), set_using_pio(), ide_hwif_restore() and ide_set_pio() as
  a direct users of ->tuneproc.

* Remove no longer needed ide_get_best_pio_mode() calls and printk-s
  reporting PIO mode selected from ->tuneproc implementations.

* Rename ->tuneproc hook to ->set_pio_mode and make 'pio' argument const.

* Remove stale comment from ide_config_drive_speed().

v2:
* Fix "ata_" prefix (Noticed by Jeff).

v3:
* Minor cleanups/fixups per Sergei's suggestions.

v4:
* Fix compile problem in drivers/ide/pci/cmd640.c
  (Noticed by Andrew Morton).

* Improve some ->set_pio_mode comments.
Reviewed-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Move ide_rate_filter() calls from host drivers to IDE core.

* Make ide_rate_filter() static.

* Make 'speed' argument of ->speedproc const.

v2:
* Fix it8213_tune_chipset() comment.

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Three main sets of changes:

1) dmi_get_system_info() return value should have been marked const,
   since callers should not be changing that data.

2) const-ify DMI internals, since DMI firmware tables should,
   whenever possible, be marked const to ensure we never ever write to
   that data area.

3) const-ify DMI API, to enable marking tables const where possible
   in low-level drivers.

And if we're really lucky, this might enable some additional
optimizations on the part of the compiler.

The bulk of the changes are #2 and #3, which are interrelated.  #1 could
have been a separate patch, but it was so small compared to the others,
it was easier to roll it into this changeset.
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Add Toshiba S1800-814 to whitelist for both pata_ali and alim15x3,
as it is correctly detected as 40-wire connected but this cable is
short enough to still use transfer modes higher than UDMA33.
Signed-off-by: NDaniel Exner <dex@dragonslave.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>