Since commit fe192a49 ("Rework gianfar
driver to use of_mdio infrastructure") the fixed-link support is
broken, the driver oopses at init_phy():

  Unable to handle kernel paging request for data at address 0x000000e4
  Faulting instruction address: 0xc01cf298
  Oops: Kernel access of bad area, sig: 11 [#1]
  [...]
  NIP [c01cf298] init_phy+0x80/0xdc
  LR [c01cf250] init_phy+0x38/0xdc
  Call Trace:
  [cf81fe80] [c01d1cf8] gfar_enet_open+0x6c/0x19c
  [cf81fea0] [c024494c] dev_open+0xfc/0x134
  [cf81fec0] [c0242edc] dev_change_flags+0x84/0x1ac
  [cf81fee0] [c0399ee0] ic_open_devs+0x168/0x2d8
  [cf81ff20] [c039b2e8] ip_auto_config+0x90/0x2a4
  [cf81ff60] [c0003884] do_one_initcall+0x34/0x1a8

This patch fixes the oops, and removes phy_node checks, and adds a call
to of_phy_connect_fixed_link() if a phy isn't attached..

Also, remove an old fixed-link code that we don't use any longer.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit aa73832c ("Rework
fs_enet driver to use of_mdio infrastructure") the fixed-link support
is broken in the fs_enet driver.

This patch fixes the support by removing a check for phy_node, and adding
a call to of_phy_connect_fixed_link().

Also set netdev parent device via SET_NETDEV_DEV() call, this is needed
so that OF MDIO core could find a node pointer for a device.

Plus, fix "if (IS_ERR(phydev))" check, in case of errors,
of_phy_connect() returns NULL, not ERR_PTR as phy_connect().
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixed-link support is broken for the ucc_eth, gianfar, and fs_enet
device drivers.  The "OF MDIO rework" patches removed most of the
support. Instead of re-adding fixed-link stuff to the drivers, this
patch adds a support function for parsing the fixed-link property
and obtaining a dummy phy to match.

Note: the dummy phy handling in arch/powerpc is a bit of a hack and
needs to be reworked.  This function is being added now to solve the
regression in the Ethernet drivers, but it should be considered a
temporary measure until the fixed link handling can be reworked.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reset rx chain before trying to drain it.
Shut interrupts off last, incase there's something to report.
Signed-off-by: NMike McCormack <mikem@ring3k.org>
Acked-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The values in the advertising field are typically ADVERTISED_xxx, not
SUPPORTED_xxx.  Both SUPPORTED_10000baseT_Full and
ADVERTISED_1000baseT_Full have the same value.

The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@
struct ethtool_cmd E;
@@
*E.advertising = SUPPORTED_10000baseT_Full
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the NULL test is necessary, then the dereference should be moved below
the NULL test.

The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@
type T;
expression E,E1;
identifier i,fld;
statement S;
@@

- T i = E->fld;
+ T i;
  ... when != E=E1
      when != i
  if (E == NULL||...) S
+ i = E->fld;
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the NULL test is necessary, then the dereferences should be moved below
the NULL test.

The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@
type T;
expression E,E1;
identifier i,fld;
statement S;
@@

- T i = E->fld;
+ T i;
  ... when != E=E1
      when != i
  BUG_ON (E == NULL||...);
+ i = E->fld;
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NEvgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Many Nokia handsets support a Phonet interface to the cellular modem
via a vendor-specific USB interface. CDC Phonet follows the
Communications Device Class model, with one control interface, and
and a pair of inactive and active data alternative interface. The later
has two bulk endpoint, one per direction.

This was tested against Nokia E61, Nokia N95, and the existing Phonet
gadget function for the Linux composite USB gadget framework.
Signed-off-by: NRémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set the driver data before using it. Fixes an oops when doing rmmod.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A pointer to mac_sonic_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded.  Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.

Various other functions that are called by mac_sonic_probe need to move
to .devinit.text, too.

An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: NFinn Thain <fthain@telegraphics.com.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a problem when a device is stopped while in the
bus-off state. Then the carrier remains off forever.
Signed-off-by: NKurt Van Dijck <kurt.van.dijck@skynet.be>
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If dev_alloc_skb() failed in can_restart(), the device was left behind
in the bus-off state. This patch restarts the device nevertheless.
Signed-off-by: NKurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove duplicated #include('s) in
  drivers/net/can/sja1000/sja1000.c
Signed-off-by: NHuang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

rain_maker@root-forum.org wrote:
> Hello cesar,
>
> In a recent thread in a german linux forum, a user reported his PIC
> NIC not being recognized by the kernel.
>
> Fortunately he provided enough information and I was able to help him
> and get the device working with the sc92031 driver.
>
> The device ID is [1088:2031] (Vendor is called "Microcomputer Systems
> (M) Son"), here is the respective thread in "ubuntuusers.de"
>
> http://forum.ubuntuusers.de/topic/lankarte-unter-xubuntu-wird-nicht-erkannt/
>
> (Although you might not speak german, the code provided will show
> you, that the device is actually working with your driver).
>
> It would be nice, if you include this new device ID to the
> sc92031-driver.
>
> Regards,
>
> Axel Köllhofer (aka Rain_Maker)

Cc: rain_maker@root-forum.org
Signed-off-by: NCesar Eduardo Barros <cesarb@cesarb.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

3c589_cs:
re-initialize the multicast in the tc589_reset,
and spin_lock the set_multicast_list function.
Signed-off-by: NKen Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Check temperature for all PCI functions, that can allow
graceful shutdown of all interfaces on the overheated card.

Old code was only monitoring temperature for function 0 only.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

netxen: fix deadlock on dev close

The tx ring accounting fix in commit cb2107be
("netxen: fix tx ring accounting") introduced intermittent
deadlock when inteface is going down.

This was possibly combined effect of speculative tx pause,
calling netif_tx_lock instead of queue lock and unclean
synchronization with napi which could end up unmasking
interrupt.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Use D3 reset context deletion for NX2031, it cleans up
  more resources in the firmware.
o Release rx buffers after hardware context has been reset.
o Delete tx context after rx context, some firmware control
  commands are sent on tx context, so it should be the last
  to go.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Network driver for the SPI version of the Micrel KS8851
network chip.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add mac driver support for evaluation board based on w90p910.
Signed-off-by: NWan ZongShun <mcuos.com@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The kernel has used a stale email address of Andreas for a few years.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the driver received an EEM packet with CRC option enabled, driver must
compute and check the CRC of the Ethernet data. Previous version computes CRC
on Ethernet data plus the original CRC value. Skbuff is correctly trimed but
the old length is used when CRC is computed.
Signed-off-by: NVincent CUISSARD <vincent.cuissard@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove debug DPRINTK in DCB mode netlink interface.
Signed-off-by: NLucy Liu <lucy.liu@intel.com>
Acked-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change clears the address data block memory space, which is needed for
the 82598 which does not have a SAN MAC.
Signed-off-by: NLucy Liu <lucy.liu@intel.com>
Acked-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The commit changes to shutdown path broke startup on some systems.

revert commit c0bad0f2Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

E100 places it's RX packet descriptors inside skb->data and uses them
with bidirectional streaming DMA mapping. Unfortunately it fails to
transfer skb->data ownership to the device after it reads the
descriptor's status, breaking on non-coherent (e.g., ARM) platforms.

This have to be converted to use coherent memory for the descriptors.
Signed-off-by: NKrzysztof Halasa <khc@pm.waw.pl>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bonding device forbids slave device of different types under the same
master.

However, it is possible for a bonding master to change type during its
lifetime.  This can be either from ARPHRD_ETHER to ARPHRD_INFINIBAND
or the other way arround.  The change of type requires device level
multicast address cleanup because device level multicast addresses
depend on the device type.

The patch adds a call to dev_close() before the bonding master changes
type and dev_open() just after that.

In the example below I enslaved an IPoIB device (ib0) under
bond0. Since each bonding master starts as device of type ARPHRD_ETHER
by default, a change of type occurs when ib0 is enslaved.

This is how /proc/net/dev_mcast looks like without the patch

5    bond0           1     0     00ffffffff12601bffff000000000001ff96ca05
5    bond0           1     0     01005e000116
5    bond0           1     0     01005e7ffffd
5    bond0           1     0     01005e000001
5    bond0           1     0     333300000001
6    ib0             1     0     00ffffffff12601bffff000000000001ff96ca05
6    ib0             1     0     333300000001
6    ib0             1     0     01005e000001
6    ib0             1     0     01005e7ffffd
6    ib0             1     0     01005e000116
6    ib0             1     0     00ffffffff12401bffff00000000000000000001
6    ib0             1     0     00ffffffff12601bffff00000000000000000001

and this is how it looks like after the patch.

5    bond0           1     0     00ffffffff12601bffff000000000001ff96ca05
5    bond0           1     0     00ffffffff12601bffff00000000000000000001
5    bond0           1     0     00ffffffff12401bffff0000000000000ffffffd
5    bond0           1     0     00ffffffff12401bffff00000000000000000116
5    bond0           1     0     00ffffffff12401bffff00000000000000000001
6    ib0             1     0     00ffffffff12601bffff000000000001ff96ca05
6    ib0             1     0     00ffffffff12401bffff00000000000000000116
6    ib0             1     0     00ffffffff12401bffff0000000000000ffffffd
6    ib0             2     0     00ffffffff12401bffff00000000000000000001
6    ib0             2     0     00ffffffff12601bffff00000000000000000001
Signed-off-by: NMoni Shoua <monis@voltaire.com>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix misplaced parenthesis
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Parentheses are required or the comparison occurs before the bitand.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit adeab1af.

As Alan Cox explained, the TTY layer changes that went recently
to get rid of the tty->low_latency stuff fixes this already,
and even for -stable it's the ->low_latency changes that should
go in to fix this, rather than this patch.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

spin_unlock_irq() will enable interrupt in net_send_packet(),
this patch changes it to spin_lock_irqsave/spin_lock_irqrestore,
so that it doesn't enable interrupts when already disabled,
and netconsole would work properly over cs89x0/isa-skeleton.

Call trace:
netconsole write_msg()
{
 ...
 -> spin_lock_irqsave();
        -> netpoll_send_udp()
          -> netpoll_send_skb()
            -> net_send_packet()
              ->...

 -> spin_unlock_irqrestore();
 ...
}
Signed-off-by: NDongdong Deng <dongdong.deng@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't forget to unlock a mutex in phy_scan_fixups on a fail path.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

forward declaration of inline function should be avoided, or
old gcc cannot compile.
Reported-by: NTeck Choon Giam <giamteckchoon@gmail.com>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix duplicate testing of MCAST flag
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Acked-by: NJay Cliburn <jcliburn@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Guido Trentalancia reports:

I am trying to use the kiss driver in the Linux kernel that is being
shipped with Fedora 10 but unfortunately I get the following oops:

mkiss: AX.25 Multikiss, Hans Albas PE1AYX
mkiss: ax0: crc mode is auto.
ADDRCONF(NETDEV_CHANGE): ax0: link becomes ready
------------[ cut here ]------------
WARNING: at kernel/softirq.c:77 __local_bh_disable+0x2f/0x83() (Not
tainted)
[...]
unloaded: microcode]
Pid: 0, comm: swapper Not tainted 2.6.27.25-170.2.72.fc10.i686 #1
 [<c042ddfb>] warn_on_slowpath+0x65/0x8b
 [<c06ab62b>] ? _spin_unlock_irqrestore+0x22/0x38
 [<c04228b4>] ? __enqueue_entity+0xe3/0xeb
 [<c042431e>] ? enqueue_entity+0x203/0x20b
 [<c0424361>] ? enqueue_task_fair+0x3b/0x3f
 [<c041f88c>] ? resched_task+0x3a/0x6e
 [<c06ab62b>] ? _spin_unlock_irqrestore+0x22/0x38
 [<c06ab4e2>] ? _spin_lock_bh+0xb/0x16
 [<c043255b>] __local_bh_disable+0x2f/0x83
 [<c04325ba>] local_bh_disable+0xb/0xd
 [<c06ab4e2>] _spin_lock_bh+0xb/0x16
 [<f8b6f600>] mkiss_receive_buf+0x2fb/0x3a6 [mkiss]
 [<c0572a30>] flush_to_ldisc+0xf7/0x198
 [<c0572b12>] tty_flip_buffer_push+0x41/0x51
 [<f89477f2>] ftdi_process_read+0x375/0x4ad [ftdi_sio]
 [<f8947a5a>] ftdi_read_bulk_callback+0x130/0x138 [ftdi_sio]
 [<c05d4bec>] usb_hcd_giveback_urb+0x63/0x93
 [<c05ea290>] uhci_giveback_urb+0xe5/0x15f
 [<c05eaabf>] uhci_scan_schedule+0x52e/0x767
 [<c05f6288>] ? psmouse_handle_byte+0xc/0xe5
 [<c054df78>] ? acpi_ev_gpe_detect+0xd6/0xe1
 [<c05ec5b0>] uhci_irq+0x110/0x125
 [<c05d4834>] usb_hcd_irq+0x40/0xa3
 [<c0465313>] handle_IRQ_event+0x2f/0x64
 [<c046642b>] handle_level_irq+0x74/0xbe
 [<c04663b7>] ? handle_level_irq+0x0/0xbe
 [<c0406e6e>] do_IRQ+0xc7/0xfe
 [<c0405668>] common_interrupt+0x28/0x30
 [<c056821a>] ? acpi_idle_enter_simple+0x162/0x19d
 [<c0617f52>] cpuidle_idle_call+0x60/0x92
 [<c0403c61>] cpu_idle+0x101/0x134
 [<c069b1ba>] rest_init+0x4e/0x50
 =======================
---[ end trace b7cc8076093467ad ]---
------------[ cut here ]------------
WARNING: at kernel/softirq.c:136 _local_bh_enable_ip+0x3d/0xc4()
[...]
Pid: 0, comm: swapper Tainted: G        W 2.6.27.25-170.2.72.fc10.i686
 [<c042ddfb>] warn_on_slowpath+0x65/0x8b
 [<c06ab62b>] ? _spin_unlock_irqrestore+0x22/0x38
 [<c04228b4>] ? __enqueue_entity+0xe3/0xeb
 [<c042431e>] ? enqueue_entity+0x203/0x20b
 [<c0424361>] ? enqueue_task_fair+0x3b/0x3f
 [<c041f88c>] ? resched_task+0x3a/0x6e
 [<c06ab62b>] ? _spin_unlock_irqrestore+0x22/0x38
 [<c06ab4e2>] ? _spin_lock_bh+0xb/0x16
 [<f8b6f642>] ? mkiss_receive_buf+0x33d/0x3a6 [mkiss]
 [<c04325f9>] _local_bh_enable_ip+0x3d/0xc4
 [<c0432688>] local_bh_enable_ip+0x8/0xa
 [<c06ab54d>] _spin_unlock_bh+0x11/0x13
 [<f8b6f642>] mkiss_receive_buf+0x33d/0x3a6 [mkiss]
 [<c0572a30>] flush_to_ldisc+0xf7/0x198
 [<c0572b12>] tty_flip_buffer_push+0x41/0x51
 [<f89477f2>] ftdi_process_read+0x375/0x4ad [ftdi_sio]
 [<f8947a5a>] ftdi_read_bulk_callback+0x130/0x138 [ftdi_sio]
 [<c05d4bec>] usb_hcd_giveback_urb+0x63/0x93
 [<c05ea290>] uhci_giveback_urb+0xe5/0x15f
 [<c05eaabf>] uhci_scan_schedule+0x52e/0x767
 [<c05f6288>] ? psmouse_handle_byte+0xc/0xe5
 [<c054df78>] ? acpi_ev_gpe_detect+0xd6/0xe1
 [<c05ec5b0>] uhci_irq+0x110/0x125
 [<c05d4834>] usb_hcd_irq+0x40/0xa3
 [<c0465313>] handle_IRQ_event+0x2f/0x64
 [<c046642b>] handle_level_irq+0x74/0xbe
 [<c04663b7>] ? handle_level_irq+0x0/0xbe
 [<c0406e6e>] do_IRQ+0xc7/0xfe
 [<c0405668>] common_interrupt+0x28/0x30
 [<c056821a>] ? acpi_idle_enter_simple+0x162/0x19d
 [<c0617f52>] cpuidle_idle_call+0x60/0x92
 [<c0403c61>] cpu_idle+0x101/0x134
 [<c069b1ba>] rest_init+0x4e/0x50
 =======================
---[ end trace b7cc8076093467ad ]---
mkiss: ax0: Trying crc-smack
mkiss: ax0: Trying crc-flexnet

The issue was, that the locking code in mkiss was assuming it was only
ever being called in process or bh context.  Fixed by converting the
involved locking code to use irq-safe locks.

Review of other networking line disciplines shows that 6pack, both sync
and async PPP and STRIP have similar issues.  The ppp_async one is the
most interesting one as it sorts out half of the issue as far back as
2004 in commit http://git.kernel.org/?p=linux/kernel/git/tglx/history.git;a=commitdiff;h=2996d8deaeddd01820691a872550dc0cfba0c37dSigned-off-by: NRalf Baechle <ralf@linux-mips.org>
Reported-by: NGuido Trentalancia <guido@trentalancia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

alloc_etherdev() used to install a default implementation of this
operation, but it must now be explicitly installed in struct
net_device_ops.
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

alloc_etherdev() used to install default implementations of these
operations, but they must now be explicitly installed in struct
net_device_ops.
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit c3a8c5b6 ("cxgb3: move away from LLTX") exposed a bug in how
cxgb3 looks up the netdev_queue it stashes away in a qset during
initialization.  For multiport devices, the TX queue index it uses is
offset by the first_qset index of each port.  This leads to a crash
once LLTX is removed, since hard_start_xmit is called with one TX
queue lock held, while the TX reclaim timer task grabs a different
(wrong) TX queue lock when it frees skbs.

Fix this by removing the first_qset offset used to look up the TX
queue passed into t3_sge_alloc_qset() from setup_sge_qsets().
Signed-off-by: NRoland Dreier <rolandd@cisco.com>
Acked-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix coexistence of Fiber Channel over Ethernet (FCoE) and Flow Director (FDIR)
in 82599 and remove the disabling of FDIR when FCoE is enabled.

Currently, FDIR is turned off when FCoE is enabled under the assumption that
FCoE is always enabled with DCB being turned on. However, FDIR does not have
to be turned off all the time when FCoE is enabled since FCoE can be enabled
without DCB being turned on, e.g., use link pause only. This patch makes sure
that when DCB is turned on or off, FDIR is turned on or off correspondingly;
and when FCoE is enabled, it does not disable FDIR, rather, it will have FDIR
set up properly so FCoE and FDIR can coexist regardless of DCB being on or off.
Signed-off-by: NYi Zou <yi.zou@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>