Fix the runtime suspend issues result from the linking change.

Case 1:
a) link down occurs.
b) driver disable tx/rx.
c) autosuspend occurs.
d) hw linking up.
e) device suspends without enabling tx/rx.
f) couldn't wake up when receiving packets.

Case 2:
a) Nway results in linking down.
b) autosuspend occurs.
c) device suspends.
d) device may not wake up when linking up.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Split DRIVER_VERSION into NETNEXT_VERSION and NET_VERSION. Then,
according to the value of DRIVER_VERSION, we could know which
patches are used generally without comparing the source code.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The UEFI driver would enable zero length, and the Linux driver doesn't
need it. Zero length let the hw complete the transfer with length 0,
when there is no received packet. It would add the load of USB host
controller and reduce the performance.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The device reset is necessary if the hw becomes abnormal and stops
transmitting packets.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add rtl8152_pre_reset() and rtl8152_post_reset() which are used when
calling usb_reset_device(). The two functions could reduce the time
of reset when calling usb_reset_device() after probe().
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adjust napi_disable() and napi_enable() to avoid r8152_poll() start
working before rx ready. Otherwise, it may have race condition for
rx_agg.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Avoid the driver to enable WOL if the device doesn't support it.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Disable U1/U2 during initialization.
- Disable lpm when linking is on, and enable it when linking is off.
- Disable U1/U2 when enabling runtime suspend.

It is possible to let hw stop working, if the U1/U2 request occurs
during some situations. The patch is used to avoid it.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support the new USB gigabit ethernet.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This device is sold as 'NVIDIA Tegra USB 3.0 Ethernet'.
Chipset is RTL8153 and works with r8152.
Signed-off-by: NZheng Liu <zhliu@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This device is sold as 'Lenovo OneLink Pro Dock'.
Chipset is RTL8153 and works with r8152.
Signed-off-by: NVasily Titskiy <qehgt0@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This device is sold as 'Lenovo Tinkpad USB 3.0 Ethernet 4X90E51405'.
Chipset is RTL8153 and works with r8152.
Signed-off-by: NChristian Hesse <mail@eworm.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support setting the rx coalesce. Then someone could change the rx
agg timeout value through ethtool.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The rx early size is calculated with the mtu, so it has to be
re-calculated when the mtu is changed.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Separate USB_RX_EARLY_AGG into USB_RX_EARLY_TIMEOUT and USB_RX_EARLY_SIZE.

Replace r8153_set_rx_agg() with r8153_set_rx_early_timeout() and
r8153_set_rx_early_size().

Set the default timeout value according to the USB speed.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a capability which let the hw could change the settings
automatically when the power change to ON. However, the USB reset
would reset the settings to the hw default, so the driver has to
restore the relative settings. Otherwise, it would influence the
functions of the hw, and the compatibility for the USB hub and
USB host controller.

The relative settings are as following.
 - set the power down scale to 96.
 - enable the power saving function of USB 2.0.
 - disable the ALDPS of ECM mode.
 - set burst mode depending on the burst size.
 - enable the flow control of endpoint full.
 - set fifo empty boundary to 32448 bytes.
 - enable the function of exiting LPM when Rx OK occurs.
 - set the connect timer to 1.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use BIT macro to replace (1 << bits).
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

vlan_get_protocol() has been defined and use it to replace
get_protocol().
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Keep NETIF_F_HW_VLAN_CTAG_RX and NETIF_F_HW_VLAN_CTAG_TX at the
same line.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is unnecessary to accress the hw register if the device is unplugged.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace (tp->speed & LINK_STATUS) with netif_carrier_ok().
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set LPM timer to 500us, except for RTL_VER_04 which doesn't link at
USB 3.0.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If a error occurs when submitting rx, skip the remaining submissions
and try to submit them again next time.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Read OCP register 0xa43a~0xa43b would clear some flags which the hw
would use, and it may let the device lost. However, the unit of
reading is 4 bytes. That is, it would read 0xa438~0xa43b when calling
sram_read() to read OCP_SRAM_DATA.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For ocp_write_word() and ocp_write_byte(), there is a generic_ocp_read()
which is used to read the whole 4 byte data, keep the unchanged bytes,
and modify the expected bytes. However, the "byen" could be used to
determine which bytes of the 4 bytes to write, so the action could be
removed.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace tasklet with NAPI.

Add rx_queue to queue the remaining rx packets if the number of the
rx packets is more than the request from poll().
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The same macros are used for rx as well. So rename it.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't submit the rx if the device is unplugged, stopped, or
linking down.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove rtl_start_rx() from rtl_enable() and put it after calling
netif_carrier_on().
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support ndo_features_check to avoid:
 - the transport offset is more than the hw limitation when using hw checksum.
 - the skb->len of a GSO packet is more than the limitation.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Redefine REALTEK_USB_DEVICE for the desired USB interface for probe().
There are three USB interfaces for the device. USB_CLASS_COMM and
USB_CLASS_CDC_DATA are for ECM mode (config #2). USB_CLASS_VENDOR_SPEC
is for the vendor mode (config #1). However, we are not interesting
in USB_CLASS_CDC_DATA for probe(), so redefine REALTEK_USB_DEVICE
to ignore the USB interface class of USB_CLASS_CDC_DATA.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If there is a error for r8152_submit_rx(), add the remaining rx
buffers to the list. Then the remaining rx buffers could be
submitted later.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The behavior of handling the returned status from r8152_submit_rx()
is almost same, so let r8152_submit_rx() deal with the error
directly. This could avoid the duplicate code.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the device is unplugged or !netif_running(), the workqueue
doesn't need to wake the device, and could return directly.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Clear the flag of SCHEDULE_TASKLET in bottom_half() to avoid
re-schedule the tasklet again by workqueue.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The INIT_LIST_HEAD(&tp->rx_done) would be done in rtl_start_rx(),
so remove the unnecessary one in alloc_all_mem().
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PIDs are only used in the id table, so the definitions are
unnacessary. Remove them wouldn't have confusion.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace using VID/PID with using tp->version to initialize the ops.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move r8152b_get_version() to the location before rtl_ops_init().
Then, the rtl_ops_init() could use tp->version.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Let the tasklet only be enabled after open(), and be disabled for
the other situation. The tasklet is only necessary after open() for
tx/rx, so it could be disabled by default.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>