1. 18 4月, 2008 7 次提交
    • T
      libata: rename SFF functions · 9363c382
      Tejun Heo 提交于
      SFF functions have confusing names.  Some have sff prefix, some have
      bmdma, some std, some pci and some none.  Unify the naming by...
      
      * SFF functions which are common to both BMDMA and non-BMDMA are
        prefixed with ata_sff_.
      
      * SFF functions which are specific to BMDMA are prefixed with
        ata_bmdma_.
      
      * SFF functions which are specific to PCI but apply to both BMDMA and
        non-BMDMA are prefixed with ata_pci_sff_.
      
      * SFF functions which are specific to PCI and BMDMA are prefixed with
        ata_pci_bmdma_.
      
      * Drop generic prefixes from LLD specific routines.  For example,
        bfin_std_dev_select -> bfin_dev_select.
      
      The following renames are noteworthy.
      
        ata_qc_issue_prot() -> ata_sff_qc_issue()
        ata_pci_default_filter() -> ata_bmdma_mode_filter()
        ata_dev_try_classify() -> ata_sff_dev_classify()
      
      This rename is in preparation of separating SFF support out of libata
      core layer.  This patch strictly renames functions and doesn't
      introduce any behavior difference.
      Signed-off-by: NTejun Heo <htejun@gmail.com>
      9363c382
    • T
      libata: stop overloading port_info->private_data · 887125e3
      Tejun Heo 提交于
      port_info->private_data is currently used for two purposes - to record
      private data about the port_info or to specify host->private_data to
      use when allocating ata_host.
      
      This overloading is confusing and counter-intuitive in that
      port_info->private_data becomes host->private_data instead of
      port->private_data.  In addition, port_info and host don't correspond
      to each other 1-to-1.  Currently, the first non-NULL
      port_info->private_data is used.
      
      This patch makes port_info->private_data just be what it is -
      private_data for the port_info where LLD can jot down extra info.
      libata no longer sets host->private_data to the first non-NULL
      port_info->private_data, @host_priv argument is added to
      ata_pci_init_one() instead.  LLDs which use ata_pci_init_one() can use
      this argument to pass in pointer to host private data.  LLDs which
      don't should use init-register model anyway and can initialize
      host->private_data directly.
      
      Adding @host_priv instead of using init-register model for LLDs which
      use ata_pci_init_one() is suggested by Alan Cox.
      Signed-off-by: NTejun Heo <htejun@gmail.com>
      Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
      887125e3
    • T
      libata: make ata_pci_init_one() not use ops->irq_handler and pi->sht · 1bd5b715
      Tejun Heo 提交于
      ata_pci_init_one() is the only function which uses ops->irq_handler
      and pi->sht.  Other initialization functions take the same information
      as arguments.  This causes confusion and duplicate unused entries in
      structures.
      
      Make ata_pci_init_one() take sht as an argument and use ata_interrupt
      implicitly.  All current users use ata_interrupt and if different irq
      handler is necessary open coding ata_pci_init_one() using
      ata_prepare_sff_host() and ata_activate_sff_host can be done under ten
      lines including error handling and driver which requires custom
      interrupt handler is likely to require custom initialization anyway.
      
      As ata_pci_init_one() was the last user of ops->irq_handler, this
      patch also kills the field.
      Signed-off-by: NTejun Heo <htejun@gmail.com>
      1bd5b715
    • T
      libata: implement and use ops inheritance · 029cfd6b
      Tejun Heo 提交于
      libata lets low level drivers build ata_port_operations table and
      register it with libata core layer.  This allows low level drivers
      high level of flexibility but also burdens them with lots of
      boilerplate entries.
      
      This becomes worse for drivers which support related similar
      controllers which differ slightly.  They share most of the operations
      except for a few.  However, the driver still needs to list all
      operations for each variant.  This results in large number of
      duplicate entries, which is not only inefficient but also error-prone
      as it becomes very difficult to tell what the actual differences are.
      
      This duplicate boilerplates all over the low level drivers also make
      updating the core layer exteremely difficult and error-prone.  When
      compounded with multi-branched development model, it ends up
      accumulating inconsistencies over time.  Some of those inconsistencies
      cause immediate problems and fixed.  Others just remain there dormant
      making maintenance increasingly difficult.
      
      To rectify the problem, this patch implements ata_port_operations
      inheritance.  To allow LLDs to easily re-use their own ops tables
      overriding only specific methods, this patch implements poor man's
      class inheritance.  An ops table has ->inherits field which can be set
      to any ops table as long as it doesn't create a loop.  When the host
      is started, the inheritance chain is followed and any operation which
      isn't specified is taken from the nearest ancestor which has it
      specified.  This operation is called finalization and done only once
      per an ops table and the LLD doesn't have to do anything special about
      it other than making the ops table non-const such that libata can
      update it.
      
      libata provides four base ops tables lower drivers can inherit from -
      base, sata, pmp, sff and bmdma.  To avoid overriding these ops
      accidentaly, these ops are declared const and LLDs should always
      inherit these instead of using them directly.
      
      After finalization, all the ops table are identical before and after
      the patch except for setting .irq_handler to ata_interrupt in drivers
      which didn't use to.  The .irq_handler doesn't have any actual effect
      and the field will soon be removed by later patch.
      
      * sata_sx4 is still using old style EH and currently doesn't take
        advantage of ops inheritance.
      Signed-off-by: NTejun Heo <htejun@gmail.com>
      029cfd6b
    • T
      libata: implement and use SHT initializers · 68d1d07b
      Tejun Heo 提交于
      libata lets low level drivers build scsi_host_template and register it
      to the SCSI layer.  This allows low level drivers high level of
      flexibility but also burdens them with lots of boilerplate entries.
      
      This patch implements SHT initializers which can be used to initialize
      all the boilerplate entries in a sht.  Three variants of them are
      implemented - BASE, BMDMA and NCQ - for different types of drivers.
      Note that entries can be overriden by putting individual initializers
      after the helper macro.
      
      All sht tables are identical before and after this patch.
      Signed-off-by: NTejun Heo <htejun@gmail.com>
      68d1d07b
    • T
      libata: normalize port_info, port_operations and sht tables · 6bd99b4e
      Tejun Heo 提交于
      Over the time, port info, ops and sht structures developed quite a bit
      of inconsistencies.  This patch updates drivers.
      
      * Enable/disable_pm callbacks added to all ahci ops tables.
      
      * Every driver for SFF controllers now uses ata_sff_port_start()
        instead of ata_port_start() unless the driver has custom
        implementation.
      
      * Every driver for SFF controllers now uses ata_pci_default_filter()
        unless the driver has custom implementation.
      
      * Removed an odd port_info->sht initialization from ata_piix.c.
        Likely a merge byproduct.
      
      * A port which has ATA_FLAG_SATA set doesn't need to set cable_detect
        to ata_cable_sata().  Remove it from via and mv port ops.
      
      * Some drivers had unnecessary .max_sectors initialization which is
        ignored and was missing .slave_destroy callback.  Fixed.
      
      * Removed unnecessary sht initializations port_info's.
      
      * Removed onsolete scsi device suspend/resume callbacks from
        pata_bf54x.
      
      * No reason to set ata_pci_default_filter() and bmdma functions for
        PIO-only drivers.  Remove those callbacks and replace
        ata_bmdma_irq_clear with ata_noop_irq_clear.
      
      * pata_platform sets port_start to ata_dummy_ret0.  port_start can
        just be set to NULL.
      
      * sata_fsl supports NCQ but was missing qc_defer.  Fixed.
      
      * pata_rb600_cf implements dummy port_start.  Removed.
      Signed-off-by: NTejun Heo <htejun@gmail.com>
      6bd99b4e
    • T
      libata: PCI device should be powered up before being accessed · f08048e9
      Tejun Heo 提交于
      PCI device should be powered up or powered up before its PCI regsiters
      are accessed.  Although PCI configuration register access is allowed
      in D3hot, PCI device is free to reset its status when transiting from
      D3hot to D0 causing configuration data to change.
      
      Many libata SFF drivers which use ata_pci_init_one() read and update
      configuration registers before calling ata_pci_init_one() which
      enables the PCI device.  Also, in resume paths, some drivers access
      registers without resuming the PCI device.
      
      This patch adds a call to pcim_enable_device() in init path if
      register is accessed before calling ata_pci_init_one() and make resume
      paths first resume PCI devices, access PCI configuration regiters then
      resume ATA host.
      
      While at it...
      
      * cmd640 was strange in that it set ->resume even when CONFIG_PM is
        not.  This is by-product of minimal build fix.  Updated.
      
      * In cs5530, Don't BUG() on reinit failure.  Just whine and fail
        resume.
      Signed-off-by: NTejun Heo <htejun@gmail.com>
      f08048e9
  2. 20 10月, 2007 1 次提交
  3. 13 10月, 2007 3 次提交
  4. 01 8月, 2007 1 次提交
  5. 10 7月, 2007 1 次提交
  6. 22 5月, 2007 1 次提交
  7. 12 5月, 2007 2 次提交
    • T
      libata: clean up SFF init mess · 1626aeb8
      Tejun Heo 提交于
      The intention of using port_mask in SFF init helpers was to eventually
      support exoctic configurations such as combination of legacy and
      native port on the same controller.  This never became actually
      necessary and the related code always has been subtly broken one way
      or the other.  Now that new init model is in place, there is no reason
      to make common helpers capable of handling all corner cases.  Exotic
      cases can simply dealt within LLDs as necessary.
      
      This patch removes port_mask handling in SFF init helpers.  SFF init
      helpers don't take n_ports argument and interpret it into port_mask
      anymore.  All information is carried via port_info.  n_ports argument
      is dropped and always two ports are allocated.  LLD can tell SFF to
      skip certain port by marking it dummy.  Note that SFF code has been
      treating unuvailable ports this way for a long time until recent
      breakage fix from Linus and is consistent with how other drivers
      handle with unavailable ports.
      
      This fixes 1-port legacy host handling still broken after the recent
      native mode fix and simplifies SFF init logic.  The following changes
      are made...
      
      * ata_pci_init_native_host() and ata_init_legacy_host() both now try
        to initialized whatever they can and mark failed ports dummy.  They
        return 0 if any port is successfully initialized.
      
      * ata_pci_prepare_native_host() and ata_pci_init_one() now doesn't
        take n_ports argument.  All info should be specified via port_info
        array.  Always two ports are allocated.
      
      * ata_pci_init_bmdma() exported to be used by LLDs in exotic cases.
      
      * port_info handling in all LLDs are standardized - all port_info
        arrays are const stack variable named ppi.  Unless the second port
        is different from the first, its port_info is specified as NULL
        (tells libata that it's identical to the last non-NULL port_info).
      
      * pata_hpt37x/hpt3x2n: don't modify static variable directly.  Make an
        on-stack copy instead as ata_piix does.
      
      * pata_uli: It has 4 ports instead of 2.  Don't use
        ata_pci_prepare_native_host().  Allocate the host explicitly and use
        init helpers.  It's simple enough.
      Signed-off-by: NTejun Heo <htejun@gmail.com>
      Signed-off-by: NJeff Garzik <jeff@garzik.org>
      1626aeb8
    • T
      libata: reimplement suspend/resume support using sdev->manage_start_stop · 9666f400
      Tejun Heo 提交于
      Reimplement suspend/resume support using sdev->manage_start_stop.
      
      * Device suspend/resume is now SCSI layer's responsibility and the
        code is simplified a lot.
      
      * DPM is dropped.  This also simplifies code a lot.  Suspend/resume
        status is port-wide now.
      
      * ata_scsi_device_suspend/resume() and ata_dev_ready() removed.
      
      * Resume now has to wait for disk to spin up before proceeding.  I
        couldn't find easy way out as libata is in EH waiting for the
        disk to be ready and sd is waiting for EH to complete to issue
        START_STOP.
      
      * sdev->manage_start_stop is set to 1 in ata_scsi_slave_config().
        This fixes spindown on shutdown and suspend-to-disk.
      Signed-off-by: NTejun Heo <htejun@gmail.com>
      Signed-off-by: NJeff Garzik <jeff@garzik.org>
      9666f400
  8. 29 4月, 2007 1 次提交
  9. 03 3月, 2007 2 次提交
  10. 10 2月, 2007 3 次提交
    • A
      libata: add another IRQ calls (libata drivers) · 246ce3b6
      Akira Iguchi 提交于
      This patch is against each libata driver.
      
      Two IRQ calls are added in ata_port_operations.
      - irq_on() is used to enable interrupts.
      - irq_ack() is used to acknowledge a device interrupt.
      
      In most drivers, ata_irq_on() and ata_irq_ack() are used for
      irq_on and irq_ack respectively.
      
      In some drivers (ex: ahci, sata_sil24) which cannot use them
      as is, ata_dummy_irq_on() and ata_dummy_irq_ack() are used.
      Signed-off-by: NKou Ishizaki <kou.ishizaki@toshiba.co.jp>
      Signed-off-by: NAkira Iguchi <akira2.iguchi@toshiba.co.jp>
      Signed-off-by: NJeff Garzik <jeff@garzik.org>
      246ce3b6
    • T
      libata: convert to iomap · 0d5ff566
      Tejun Heo 提交于
      Convert libata core layer and LLDs to use iomap.
      
      * managed iomap is used.  Pointer to pcim_iomap_table() is cached at
        host->iomap and used through out LLDs.  This basically replaces
        host->mmio_base.
      
      * if possible, pcim_iomap_regions() is used
      
      Most iomap operation conversions are taken from Jeff Garzik
      <jgarzik@pobox.com>'s iomap branch.
      Signed-off-by: NTejun Heo <htejun@gmail.com>
      Signed-off-by: NJeff Garzik <jeff@garzik.org>
      0d5ff566
    • T
      libata: update libata LLDs to use devres · 24dc5f33
      Tejun Heo 提交于
      Update libata LLDs to use devres.  Core layer is already converted to
      support managed LLDs.  This patch simplifies initialization and fixes
      many resource related bugs in init failure and detach path.  For
      example, all converted drivers now handle ata_device_add() failure
      gracefully without excessive resource rollback code.
      
      As most resources are released automatically on driver detach, many
      drivers don't need or can do with much simpler ->{port|host}_stop().
      In general, stop callbacks are need iff port or host needs to be given
      commands to shut it down.  Note that freezing is enough in many cases
      and ports are automatically frozen before being detached.
      Signed-off-by: NTejun Heo <htejun@gmail.com>
      Signed-off-by: NJeff Garzik <jeff@garzik.org>
      24dc5f33
  11. 25 1月, 2007 1 次提交
  12. 03 12月, 2006 1 次提交
  13. 02 12月, 2006 1 次提交
  14. 29 11月, 2006 1 次提交
  15. 29 9月, 2006 1 次提交
  16. 27 9月, 2006 1 次提交
  17. 31 8月, 2006 1 次提交
  18. 30 8月, 2006 1 次提交