wrap the readb(), writeb() into inline function calls.
It would make the driver more clearer to support platform
with different register offset.
Signed-off-by: NJingchang Lu <b35083@freescale.com>
Reviewed-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The id_entry field should be changed by platform driver core,
driver should prevent changing it derectly. Use local variable
to save and extract platform_device_id info of the dts devices
instead.
Signed-off-by: NJingchang Lu <b35083@freescale.com>
Reviewed-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The module clk should be enabled before write to
its register in probe(), and the clk can be disabled
after.
Signed-off-by: NJingchang Lu <b35083@freescale.com>
Reviewed-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

using struct representing the i2c clk{div, val} pair would
make the i2c_clk_div array more clear.
Signed-off-by: NJingchang Lu <b35083@freescale.com>
Reviewed-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Add support for the secondary SMBus controller on the AMD SB800 and AMD FCH
chipsets.
Signed-off-by: NRudolf Marek <r.marek@assembler.cz>
Tested-by: NPaul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

While writing the i2c-imc driver, I noticed that the warning message
when the i2c core can't figure out how to probe is mostly useless.
This trivial patch improves it.
Signed-off-by: NAndy Lutomirski <luto@amacapital.net>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Keystone SOCs uses the same I2C IP as available on DaVinci SOCs.
Update the config so that ARCH_KEYSTONE can use it.
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

This driver no longer uses definitions from mach/hardware.h.
On the other hand, including this header breaks this driver
on non-davinci platforms which don't have such a header.
Acked-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SIMPLE_DEV_PM_OPS are only used when
the CONFIG_PM_SLEEP is enabled.

drivers/i2c/busses/i2c-bfin-twi.c:585:12: warning: 'i2c_bfin_twi_suspend' defined but not used [-Wunused-function]
drivers/i2c/busses/i2c-bfin-twi.c:600:12: warning: 'i2c_bfin_twi_resume' defined but not used [-Wunused-function]
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Add CONFIG_PM_SLEEP to suspend function to fix the following build
warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SIMPLE_DEV_PM_OPS are only used when
the CONFIG_PM_SLEEP is enabled.

drivers/i2c/busses/i2c-puv3.c:249:12: warning: 'puv3_i2c_suspend' defined but not used [-Wunused-function]
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SIMPLE_DEV_PM_OPS are only used when
the CONFIG_PM_SLEEP is enabled.

drivers/i2c/busses/i2c-pnx.c:599:12: warning: 'i2c_pnx_controller_suspend' defined but not used [-Wunused-function]
drivers/i2c/busses/i2c-pnx.c:608:12: warning: 'i2c_pnx_controller_resume' defined but not used [-Wunused-function]
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SIMPLE_DEV_PM_OPS are only used when
the CONFIG_PM_SLEEP is enabled.

drivers/i2c/busses/i2c-stu300.c:945:12: warning: 'stu300_suspend' defined but not used [-Wunused-function]
drivers/i2c/busses/i2c-stu300.c:954:12: warning: 'stu300_resume' defined but not used [-Wunused-function]
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SIMPLE_DEV_PM_OPS are only used when
the CONFIG_PM_SLEEP is enabled.

drivers/i2c/busses/i2c-ocores.c:460:12: warning: 'ocores_i2c_suspend' defined but not used [-Wunused-function]
drivers/i2c/busses/i2c-ocores.c:471:12: warning: 'ocores_i2c_resume' defined but not used [-Wunused-function]
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SIMPLE_DEV_PM_OPS are only used when
the CONFIG_PM_SLEEP is enabled.

drivers/i2c/busses/i2c-designware-platdrv.c:211:12: warning: 'dw_i2c_suspend' defined but not used [-Wunused-function]
drivers/i2c/busses/i2c-designware-platdrv.c:221:12: warning: 'dw_i2c_resume' defined but not used [-Wunused-function]
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SIMPLE_DEV_PM_OPS are only used when
the CONFIG_PM_SLEEP is enabled.

drivers/i2c/busses/i2c-mpc.c:724:12: warning: 'mpc_i2c_suspend' defined but not used [-Wunused-function]
drivers/i2c/busses/i2c-mpc.c:734:12: warning: 'mpc_i2c_resume' defined but not used [-Wunused-function]

Also, this patch makes mpc_i2c_pm_ops static, because mpc_i2c_pm_ops
is not exported.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

stmp_reset_block() may fail, so let's check its return value and propagate it in
the case of error.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

Since commit ab78029e (drivers/pinctrl: grab default handles from device core),
we can rely on device core for setting the default pins. Compile tested only.

Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The I2C adapters on Freescale MPC107/824x/85xx/512x/52xx/83xx/86xx all
have the same name "MPC adapter". Since I2C adapter numbers can change
across reboots and even after loading/unloading an I2C bus master driver,
adapter names have to be used to identify adapters and thus should be
unique and well defined. Since this is not the case with this driver,
it is difficult if not impossible to identify a specific adapter from
user space on affected platforms.

To remedy the problem, use the adapter memory address as part of the
adapter name.

With this patch, adapter names are:
On P2020:
MPC adapter at 0xfff703000
MPC adapter at 0xfff703100

On P5040:
MPC adapter at 0xffe118000
MPC adapter at 0xffe118100
MPC adapter at 0xffe119000
MPC adapter at 0xffe119100
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

i2c_put_adapter dereferences i2c_adapter pointer passed without check
for NULL. This adds a check for non-NULL pointer to allow i2c_put_adapter
called with NULL and behave the same way i2c_release_client does already.
It allows to simplify drivers where you need to release the adapter
during probe failures.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

If both IC_EMPTYFIFO_HOLD_MASTER_EN and IC_RESTART_EN are set to 1, the
Designware I2C controller doesn't generate RESTART unless user specifically
requests it by setting RESTART bit in IC_DATA_CMD register.

Since IC_EMPTYFIFO_HOLD_MASTER_EN setting can't be detected from hardware
register, we must always manually set the restart bit between messages.
Signed-off-by: NChew, Chiau Ee <chiau.ee.chew@intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

To enter high speed mode, following steps should be done:
1. When running in high speed mode, i2c clock rate is different
from standard mode. Clock rate must be set according to
specification first.
2. When i2c controller sends a master code and wins arbitration,
high speed mode is entered.

If you want to enable high speed mode, the following members of
platform data should be set to proper value:
1. "high_mode" should be set to "1".
2. "master_code" should be set to "8'b 0000_1xxx"(x is 0 or 1).
   If no master_code is set, set to default value 0xe.
3. "rate" should be set according to specification.
Signed-off-by: NLeilei Shang <shangll@marvell.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Add some necessary braces that have been removed during driver cleanup.
This fixes the I2C prescaler calculation.
Signed-off-by: NMichael Brunner <michael.brunner@kontron.com>
Tested-by: NGuenter Roeck <linux@roeck-us.net>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Recently we have been seing some reports about PIO mode not working properly.

- http://www.spinics.net/lists/linux-i2c/msg11985.html
- http://marc.info/?l=linux-i2c&m=137235593101385&w=2
- https://lkml.org/lkml/2013/6/24/430

Let's use DMA mode even for small transfers.

Without this patch, i2c reads the incorrect sgtl5000 version on a mx28evk when
touchscreen is enabled:

[    5.856270] sgtl5000 0-000a: Device with ID register 0 is not a sgtl5000
[    9.877307] sgtl5000 0-000a: ASoC: failed to probe CODEC -19
[    9.883528] mxs-sgtl5000 sound.12: ASoC: failed to instantiate card -19
[    9.892955] mxs-sgtl5000 sound.12: snd_soc_register_card failed (-19)

Cc: <stable@vger.kernel.org>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NLucas Stach <l.stach@pengutronix.de>
Acked-by: NMarek Vasut <marex@denx.de>

[wsa: we have a proper solution for -next, so this non intrusive
solution is OK for now]
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Forgot to use the appropriate math64 function.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@gmail.com>

Flash update routine was improperly checking register read API return value.
Modify register read API and perform proper error check.
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Set link speed and duplex to unknown when link is not up.
Signed-off-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Do not obtain link speed from register when adapter
  link is down.
Signed-off-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver was not handling external loopback diagnostic
test request.
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NPratik Pujar <pratik.pujar@qlogic.com>
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Delete MAC address from the adapter's filter table
  if the source MAC address of ingress packet matches.
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver was passing the address of a pointer instead of
the pointer itself.
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

IRQF_DISABLED is a no-op by now and should be removed.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Without this patch, the values for ideality (register 0x4b) and ideality
selection mask (register 0x4c) are inverted.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: stable@vger.kernel.org # 3.9+
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

[  198.720048] ------------[ cut here ]------------
[  198.720108] WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:255 dev_watchdog+0x229/0x240()
[  198.720118] NETDEV WATCHDOG: eth0 (sis900): transmit queue 0 timed out
[  198.720125] Modules linked in: bridge stp llc dmfe sundance 3c59x sis900 mii
[  198.720159] CPU: 0 PID: 0 Comm: swapper Not tainted 3.11.0-rc3+ #12
[  198.720167] Hardware name: System Manufacturer System Name/TUSI-M, BIOS ASUS TUSI-M ACPI BIOS
Revision 1013 Beta 001 12/14/2001
[  198.720175]  000000ff c13fa6b9 c169ddcc c12208d6 c169ddf8 c1031e4d c1664a84 c169de24
[  198.720197]  00000000 c165f5ea 000000ff c13fa6b9 00000001 000000ff c1664a84 c169de10
[  198.720217]  c1031f13 00000009 c169de08 c1664a84 c169de24 c169de50 c13fa6b9 c165f5ea
[  198.720240] Call Trace:
[  198.720257]  [<c13fa6b9>] ? dev_watchdog+0x229/0x240
[  198.720274]  [<c12208d6>] dump_stack+0x16/0x20
[  198.720306]  [<c1031e4d>] warn_slowpath_common+0x7d/0xa0
[  198.720318]  [<c13fa6b9>] ? dev_watchdog+0x229/0x240
[  198.720330]  [<c1031f13>] warn_slowpath_fmt+0x33/0x40
[  198.720342]  [<c13fa6b9>] dev_watchdog+0x229/0x240
[  198.720357]  [<c103f158>] call_timer_fn+0x78/0x150
[  198.720369]  [<c103f0e0>] ? internal_add_timer+0x40/0x40
[  198.720381]  [<c13fa490>] ? dev_init_scheduler+0xa0/0xa0
[  198.720392]  [<c103f33f>] run_timer_softirq+0x10f/0x200
[  198.720412]  [<c103954f>] ? __do_softirq+0x6f/0x210
[  198.720424]  [<c13fa490>] ? dev_init_scheduler+0xa0/0xa0
[  198.720435]  [<c1039598>] __do_softirq+0xb8/0x210
[  198.720467]  [<c14b54d2>] ? _raw_spin_unlock+0x22/0x30
[  198.720484]  [<c1003245>] ? handle_irq+0x25/0xd0
[  198.720496]  [<c1039c0c>] irq_exit+0x9c/0xb0
[  198.720508]  [<c14bc9d7>] do_IRQ+0x47/0x94
[  198.720534]  [<c1056078>] ? hrtimer_start+0x28/0x30
[  198.720564]  [<c14bc8b1>] common_interrupt+0x31/0x38
[  198.720589]  [<c1008692>] ? default_idle+0x22/0xa0
[  198.720600]  [<c10083c7>] arch_cpu_idle+0x17/0x30
[  198.720631]  [<c106d23d>] cpu_startup_entry+0xcd/0x180
[  198.720643]  [<c14ae30a>] rest_init+0xaa/0xb0
[  198.720654]  [<c14ae260>] ? reciprocal_value+0x50/0x50
[  198.720668]  [<c17044e0>] ? repair_env_string+0x60/0x60
[  198.720679]  [<c1704bda>] start_kernel+0x29a/0x350
[  198.720690]  [<c17044e0>] ? repair_env_string+0x60/0x60
[  198.720721]  [<c1704269>] i386_start_kernel+0x39/0xa0
[  198.720729] ---[ end trace 81e0a6266f5c73a8 ]---
[  198.720740] eth0: Transmit timeout, status 00000204 00000000

timer routine checks the link status and if it's up calls
netif_carrier_on() allowing upper layer to start the tx queue
even if the auto-negotiation process is not finished.

Also remove ugly auto-negotiation check from the sis900_start_xmit()

CC: Duan Fugang <B38611@freescale.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDenis Kirjanov <kda@linux-powerpc.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This message was added in commit a7154cb8 (June 2004, [PATCH] r8169:
link handling and phy reset rework) and is printed every ten seconds
when no cable is connected and runtime power management is disabled.
(Before that commit, "Reset RTL8169s PHY" would be printed instead.)
Signed-off-by: NPeter Wu <lekensteyn@gmail.com>
Acked-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

IRQF_DISABLED is a no-op by now and should be
removed.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Acked-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It's quite unlikely that dev_set_promiscuity will fail,
but worth checking just in case.

Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

macvlan passthrough mode is special: it's not possible to switch to or
from it through a netlink command.

But if you try, the command will succeed, which is
confusing.

Validate input and return error to user.

Cc:  Sridhar Samudrala <sri@us.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>