Implement API support to return AFC frequency shift, as this device
supports it. The only other driver that implements it is tda9887,
and the frequency there is reported in Hz. So, use Hz also for this
tuner.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

There are several bugs at the signal strength algorithm:

	- It is using logical OR, instead of bit OR;
	- It doesn't wait up to 18 ms as it should;
	- the strength range is not ok.

Rework on it, in order to make it work.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

If g_tuner is called and the tuner is able to return the signal strength
via has_signal(), call the tunner callback to retrieve such data for all
tuner types, not only for radio ones.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Change the firmware logic to use request_firmware_nowait(), and
to preserve the loaded firmwares in memory, to reduce the risk
of troubles with buggy userspace apps.

With this change, while the firmware is being loaded, the driver
will return -EAGAIN to any calls. If, for some reason, firmware
failed to be loaded from userspace, it will return -ENODEV.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

If firmware is not loaded for some reason, or if it is not ready
yet, it makes no sense to honour to any DVB callbacks.

So, return -EAGAIN, as the error condition may be temporary.
If the device doesn't initialize, either because it requires a
firmware or because there's an error during init_drxk, returns
-ENODEV, to indicate such error, on all DVB callbacks.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Don't allow other devices at the same I2C bus to use it during
firmware load, in order to prevent using the device while it is
not on a sane state.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

As it will be using the unlocked version of i2c_transfer during
firmware loads, make sure that the priv state routine will be
used on all I2C calls, in preparation for the next patch that
will implement an exclusive lock mode to be used during firmware
load, at drxk_init.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The firmware blob may not be available when the driver probes.

Instead of blocking the whole kernel use request_firmware_nowait() and
continue without firmware.

This shouldn't be that bad on drx-k devices, as they all seem to have an
internal firmware. So, only the firmware update will take a little longer
to happen.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Some drivers (in particular for TV cards) need exclusive access to
their I2C buses for specific operations. Export an unlocked flavor
of i2c_transfer to give them full control.

The unlocked flavor has the following limitations:
* Obviously, caller must hold the i2c adapter lock.
* No debug messages are logged. We don't want to log messages while
  holding a rt_mutex.
* No check is done on the existence of adap->algo->master_xfer. It
  is thus the caller's responsibility to ensure that the function is
  OK to call.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Cc: Ravi Kumar V <kumarrav@codeaurora.org>
Signed-off-by: NBenoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Make it possible for gpio-ir-recv users to choose a map name.

Cc: Ravi Kumar V <kumarrav@codeaurora.org>
Signed-off-by: NBenoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add missing information so that udev can create an entry for gpio-ir-recv under
/dev/input/by-path/ .

Cc: Ravi Kumar V <kumarrav@codeaurora.org>
Signed-off-by: NBenoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Convert radio-sf16fmi to use generic LM7000 driver.
Tested with SF16-FMI, SF16-FMP and SF16-FMD.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Convert radio-aimslab to use generic LM7000 driver.
Tested with Reveal RA300.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add very simple driver for Sanyo LM7000 AM/FM tuner chip. Only FM is supported
as there is no known HW with AM implemented.

This will be used by radio-aimslab and radio-sf16fmi.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This reverts commit 4ecbb694.

As requested by Hans Verkuil:
> You accidentally merged the wrong first version of the lm7000 patch series.
>
> These are the correct second version patches:
>
> http://patchwork.linuxtv.org/patch/11689/
> http://patchwork.linuxtv.org/patch/11690/
> http://patchwork.linuxtv.org/patch/11691/
>
> The second version is much simpler and doesn't require the creation of a whole
> new driver.
Requested-by: NHans Verkuil <hverkuil@xs4all.nl>
Cc: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This reverts commit bece083a.

As requested by Hans Verkuil:
> You accidentally merged the wrong first version of the lm7000 patch series.
>
> These are the correct second version patches:
>
> http://patchwork.linuxtv.org/patch/11689/
> http://patchwork.linuxtv.org/patch/11690/
> http://patchwork.linuxtv.org/patch/11691/
>
> The second version is much simpler and doesn't require the creation of a whole
> new driver.
Requested-by: NHans Verkuil <hverkuil@xs4all.nl>
Cc: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This reverts commit 1e70a6cf.

As requested by Hans Verkuil:
> You accidentally merged the wrong first version of the lm7000 patch series.
>
> These are the correct second version patches:
>
> http://patchwork.linuxtv.org/patch/11689/
> http://patchwork.linuxtv.org/patch/11690/
> http://patchwork.linuxtv.org/patch/11691/
>
> The second version is much simpler and doesn't require the creation of a whole
> new driver.
Requested-by: NHans Verkuil <hverkuil@xs4all.nl>
Cc: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This is basically s/getmode/getrxsubchans/ and s/setmode/setaudmode/
with some whitespace adjustment in affected lines to please the eye.
The rename is done to point out their relation to the rxsubchans and
audmode fields of struct v4l2_tuner.

I also corrected a commented out call to v4l_dbg in one of the lines.
Signed-off-by: NDaniel Glöckner <daniel-gl@gmx.net>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The switch/case was setting clock_setting that is not being used. Both switch/case and the variable definition were removed.

Currently clock is being calculated by the formula:
(state->fclk/1000000 - 8)

Tested by compilation only.
Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Tested by compilation only.
Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Tested by compilation only.
Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

In function saa7164_api_i2c_read variable regval was set but not used.

Tested by compilation only.
Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Tested by compilation only.
Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Saves 255 bytes of stack memory on cx231xx_usb_probe() by removing a char array.

Tested by compilation only.
Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NPeter Meerwald <p.meerwald@bct-electronic.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Commit 39c3d488 ("[media] cpia, stradis:
remove deprecated V4L1 drivers") removed the last file including these
five headers. Apparently it was just an oversight to keep them in the
tree. They can safely be removed now.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The windows driver used different values for the GPIOs and analog
decoder configuration. The values from the windows driver are now
used.
It also seems that the windows driver has LNA always disabled.
Thus we are doing the same (using the same flags as on windows).

I (only) tested with DVB-T and it worked quite well.

[mchehab@redhat.com: Fix merge conflicts and tested with DVB-C]
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Convert radio-sf16fmi to use generic LM7000 driver.
Tested with SF16-FMI, SF16-FMP and SF16-FMD.

radio.");
@@ -48,37 +50,40 @@ struct fmi
 	bool mute;
 	unsigned long curfreq; /* freq in kHz */
 	struct mutex lock;
+	struct lm7000 lm;
 };

 static struct fmi fmi_card;
 static struct pnp_dev *dev;
 bool pnp_attached;

-/* freq is in 1/16 kHz to internal number, hw precision is 50 kHz */
-/* It is only useful to give freq in interval of 800 (=0.05Mhz),
- * other bits will be truncated, e.g 92.7400016 -> 92.7, but
- * 92.7400017 -> 92.75
- */
-#define RSF16_ENCODE(x)	((x) / 800 + 214)
 #define RSF16_MINFREQ (87 * 16000)
 #define RSF16_MAXFREQ (108 * 16000)

-static void outbits(int bits, unsigned int data, int io)
+#define FMI_BIT_TUN_CE		(1 << 0)
+#define FMI_BIT_TUN_CLK		(1 << 1)
+#define FMI_BIT_TUN_DATA	(1 << 2)
+#define FMI_BIT_VOL_SW		(1 << 3)
+#define FMI_BIT_TUN_STRQ	(1 << 4)
+
+void fmi_set_pins(struct lm7000 *lm, u8 pins)
 {
-	while (bits--) {
-		if (data & 1) {
-			outb(5, io);
-			udelay(6);
-			outb(7, io);
-			udelay(6);
-		} else {
-			outb(1, io);
-			udelay(6);
-			outb(3, io);
-			udelay(6);
-		}
-		data >>= 1;
-	}
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Convert radio-aimslab to use generic LM7000 driver.
Tested with Reveal RA300.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add very simple driver for Sanyo LM7000 AM/FM tuner chip. Only FM is supported
as there is no known HW with AM implemented.

This will be used by radio-aimslab and radio-sf16fmi.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NEzequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

There is a specific header sound/ac97_codec.h that defines these.
All drivers should use it instead of rolling its own set of macros.
Signed-off-by: NEzequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NEzequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NEzequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

And fix initial control setup.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This driver allowed only one open filehandle. This is against the spec, so
fix the driver by assigning proper ownership when streaming.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>