pci_restore_state only ever returns 0, thus there is no benefit in
having it return any value.  Also, a large majority of the callers do
not check the return code of pci_restore_state.  Make the
pci_restore_state a void return and avoid the overhead.
Acked-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NJon Mason <jon.mason@exar.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

We currently refuse to touch the ASPM registers if the BIOS tells us that
ASPM isn't supported. This can cause problems if the BIOS has (for any
reason) enabled ASPM on some devices anyway. Change the code such that we
explicitly clear ASPM if the FADT indicates that ASPM isn't supported,
and make sure we tidy up appropriately on device removal in order to deal
with the hotplug case. If ASPM is disabled because the BIOS doesn't hand
over control then we won't touch the registers.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Then we can use it instead of magic number 1.
Reviewed-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Cc: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: NSheng Yang <sheng@linux.intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Then it can be used by others.
Reviewed-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NSheng Yang <sheng@linux.intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

If pcie_ports_disabled is set, pcie_port_service_register() returns
error code and select_detection_mode() should not attempt to
unregister dummy_driver and use dummy_slots.  It should return
PCIEHP_DETECT_ACPI immediately instead.
Reviewed-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

This reverts commit b126b470.

We're going back to the old behavior of allocating from bus resources
in _CRS order.
Acked-by: NH. Peter Anvin <hpa@zytor.com>
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

This reverts commit 82e3e767.

We're going back to considering bus resources in the order we found
them (in _CRS order, when we're using _CRS), so we don't need to
define any ordering.
Acked-by: NH. Peter Anvin <hpa@zytor.com>
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

I wrote this quirk awhile ago to properly setup MCP55 chips on hypertransport
busses so that interrupts reached whatever cpu happend to boot the kdump kernel.
while that works well, it was recently shown to me that a a non-hypertransport
variant of the MCP55 exists, and on those system the register that this quirk
manipulates causes hangs if you write to it.  Since the quirk was only meant to
handle errors found on MCP55 chips that have a HT interface, this patch adds a
filter to make sure the chip is an HT capable before making the needed register
adjustment.  This lets the broken MCP55s work with kdump while not breaking the
non-HT variants.

Resolves https://bugzilla.kernel.org/show_bug.cgi?id=23952

Tested successfully by the reporter and myself.

Cc: stable@kernel.org
Reported-by: NMathieu Bérard <mathieu@mberard.eu>
Acked-by: NVivek Goyal <vgoyal@redhat.com>
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Fault handling is getting enabled after enabling the interrupt-remapping (as
the success of interrupt-remapping can affect the apic mode and hence the
fault handling mode).

Hence there can potentially be some faults between the window of enabling
interrupt-remapping in the vt-d and the fault-handling of the vt-d units.

Handle any previous faults after enabling the vt-d fault handling.

For v2.6.38 cleanup, need to check if we can remove the dmar_fault() in the
enable_intr_remapping() and see if we can enable fault handling along with
enabling intr-remapping.
Signed-off-by: NSuresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <20101201062244.630417138@intel.com>
Cc: stable@kernel.org [v2.6.32+]
Acked-by: NChris Wright <chrisw@sous-sol.org>
Signed-off-by: NH. Peter Anvin <hpa@linux.intel.com>

On platforms with Intel 7500 chipset, there were some reports of system
hang/NMI's during kexec/kdump in the presence of interrupt-remapping enabled.

During kdump, there is a window where the devices might be still using old
kernel's interrupt information, while the kdump kernel is coming up. This can
cause vt-d faults as the interrupt configuration from the old kernel map to
null IRTE entries in the new kernel etc. (with out interrupt-remapping enabled,
we still have the same issue but in this case we will see benign spurious
interrupt hit the new kernel).

Based on platform config settings, these platforms seem to generate NMI/SMI
when a vt-d fault happens and there were reports that the resulting SMI causes
the  system to hang.

Fix it by masking vt-d spec defined errors to platform error reporting logic.
VT-d spec related errors are already handled by the VT-d OS code, so need to
report the same error through other channels.
Signed-off-by: NSuresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <1291667190.2675.8.camel@sbsiddha-MOBL3.sc.intel.com>
Cc: stable@kernel.org	[v2.6.32+]
Reported-by: NMax Asbock <masbock@linux.vnet.ibm.com>
Reported-and-tested-by: NTakao Indoh <indou.takao@jp.fujitsu.com>
Acked-by: NChris Wright <chrisw@sous-sol.org>
Acked-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NH. Peter Anvin <hpa@linux.intel.com>

This change enables PCI root complex support for TILEPro.  Unlike
TILE-Gx, TILEPro has no support for memory-mapped I/O, so the PCI
support consists of hypervisor upcalls for PIO, DMA, etc.  However,
the performance is fine for the devices we have tested with so far
(1Gb Ethernet, SATA, etc.).

The <asm/io.h> header was tweaked to be a little bit more aggressive
about disabling attempts to map/unmap IO port space.  The hacky
<asm/pci-bridge.h> header was rolled into the <asm/pci.h> header
and the result was simplified.  Both of the latter two headers were
preliminary versions not meant for release before now - oh well.

There is one quirk for our TILEmpower platform, which accidentally
negotiates up to 5GT and needs to be kicked down to 2.5GT.
Signed-off-by: NChris Metcalf <cmetcalf@tilera.com>

The big kernel lock has been removed from all these files at some point,
leaving only the #include.

Remove this too as a cleanup.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

I just loaded 2.6.37-rc2 on my machines, and I noticed that X no longer starts.
Running an strace of the X server shows that it's doing this:

open("/sys/bus/pci/devices/0000:07:00.0/resource0", O_RDWR) = 10
mmap(NULL, 16777216, PROT_READ|PROT_WRITE, MAP_SHARED, 10, 0) = -1 EINVAL (Invalid argument)

This code seems to be asking for a shared read/write mapping of 16MB worth of
BAR0 starting at file offset 0, and letting the kernel assign a starting
address.  Unfortunately, this -EINVAL causes X not to start.  Looking into
dmesg, there's a complaint like so:

process "Xorg" tried to map 0x01000000 bytes at page 0x00000000 on 0000:07:00.0 BAR 0 (start 0x        96000000, size 0x         1000000)

...with the following code in pci_mmap_fits:

	pci_start = (mmap_api == PCI_MMAP_SYSFS) ?
		pci_resource_start(pdev, resno) >> PAGE_SHIFT : 0;
        if (start >= pci_start && start < pci_start + size &&
                        start + nr <= pci_start + size)

It looks like the logic here is set up such that when the mmap call comes via
sysfs, the check in pci_mmap_fits wants vma->vm_pgoff to be between the
resource's start and end address, and the end of the vma to be no farther than
the end.  However, the sysfs PCI resource files always start at offset zero,
which means that this test always fails for programs that mmap the sysfs files.
Given the comment in the original commit
3b519e4e, I _think_ the old procfs files
require that the file offset be equal to the resource's base address when
mmapping.

I think what we want here is for pci_start to be 0 when mmap_api ==
PCI_MMAP_PROCFS.  The following patch makes that change, after which the Matrox
and Mach64 X drivers work again.
Acked-by: NMartin Wilck <martin.wilck@ts.fujitsu.com>
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Cast pci_resource_start() and pci_resource_len() to u64 for printk.

drivers/pci/pci-sysfs.c:753: warning: format '%16Lx' expects type 'long long unsigned int', but argument 9 has type 'resource_size_t'
drivers/pci/pci-sysfs.c:753: warning: format '%16Lx' expects type 'long long unsigned int', but argument 10 has type 'resource_size_t'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

When a PCI bus has two resources with the same start/end, e.g.,

    pci_bus 0000:04: resource 2 [mem 0xd0000000-0xd7ffffff pref]
    pci_bus 0000:04: resource 7 [mem 0xd0000000-0xd7ffffff]

the previous pci_bus_find_resource_prev() implementation would alternate
between them forever:

    pci_bus_find_resource_prev(... [mem 0xd0000000-0xd7ffffff pref])
        returns [mem 0xd0000000-0xd7ffffff]
    pci_bus_find_resource_prev(... [mem 0xd0000000-0xd7ffffff])
        returns [mem 0xd0000000-0xd7ffffff pref]
    pci_bus_find_resource_prev(... [mem 0xd0000000-0xd7ffffff pref])
        returns [mem 0xd0000000-0xd7ffffff]
    ...

This happened because there was no ordering between two resources with the
same start and end.  A resource that had the same start and end as the
cursor, but was not itself the cursor, was considered to be before the
cursor.

This patch fixes the hang by making a fixed ordering between any two
resources.

In addition, it tries to allocate from positively decoded regions before
using any subtractively decoded resources.  This means we will use a
positive decode region before a subtractive decode one, even if it means
using a smaller address.

Reference: https://bugzilla.kernel.org/show_bug.cgi?id=22062Reported-by: NBorislav Petkov <bp@amd64.org>
Tested-by: NBorislav Petkov <bp@amd64.org>
Acked-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

When we enable a PCI device, we avoid doing a lot of the initial setup
work if the device's enable count is non-zero.  If we don't fetch the
power state though, we may later fail to set up MSI due to the unknown
status.  So pick it up before we short circuit the rest due to a
pre-existing enable or mismatched enable/disable pair (as happens with
VGA devices, which are special in a special way).
Tested-by: NJesse Brandeburg <jesse.brandeburg@gmail.com>
Reported-by: NDave Airlie <airlied@linux.ie>
Tested-by: NDave Airlie <airlied@linux.ie>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The checks for valid mmaps of PCI resources made through /proc/bus/pci files
that were introduced in 9eff02e2 have several
problems:

1. mmap() calls on /proc/bus/pci files are made with real file offsets > 0,
whereas under /sys/bus/pci/devices, the start of the resource corresponds
to offset 0. This may lead to false negatives in pci_mmap_fits(), which
implicitly assumes the /sys/bus/pci/devices layout.

2. The loop in proc_bus_pci_mmap doesn't skip empty resouces. This leads
to false positives, because pci_mmap_fits() doesn't treat empty resources
correctly (the calculated size is 1 << (8*sizeof(resource_size_t)-PAGE_SHIFT)
in this case!).

3. If a user maps resources with BAR > 0, pci_mmap_fits will emit bogus
WARNINGS for the first resources that don't fit until the correct one is found.

On many controllers the first 2-4 BARs are used, and the others are empty.
In this case, an mmap attempt will first fail on the non-empty BARs
(including the "right" BAR because of 1.) and emit bogus WARNINGS because
of 3., and finally succeed on the first empty BAR because of 2.
This is certainly not the intended behaviour.

This patch addresses all 3 issues.
Updated with an enum type for the additional parameter for pci_mmap_fits().

Cc: stable@kernel.org
Signed-off-by: NMartin Wilck <martin.wilck@ts.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

While testing various randconfigs with ktest.pl, I hit the following panic:

BUG: unable to handle kernel paging request at f7e54b03
IP: [<c0d63409>] ibmphp_access_ebda+0x101/0x19bb

Adding printks, I found that the loop that reads the ebda blocks
can move out of the mapped section.

ibmphp_access_ebda: start=f7e44c00 size=5120 end=f7e46000
ibmphp_access_ebda: io_mem=f7e44d80 offset=384
ibmphp_access_ebda: io_mem=f7e54b03 offset=65283

The start of the iomap was at f7e44c00 and had a size of 5120,
making the end f7e46000. We start with an offset of 0x180 or
384, giving the first read at 0xf7e44d80. Reading that location
yields 65283, which is much bigger than the 5120 that was allocated
and makes the next read at f7e54b03 which is outside the mapped area.

Perhaps this is a bug in the driver, or buggy hardware, but this patch
is more about not crashing my box on start up and just giving a warning
if it detects this error.

This patch at least lets my box boot with just a warning.

Cc: Chandru Siddalingappa <chandru@linux.vnet.ibm.com>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Stanse found that when pdev is found and has no driver a reference is
leaked in pcifront_common_process. So add pci_dev_put there. For the
pdev == NULL case, pci_dev_put(NULL) is fine.

[v2: Updated to not dereference pcidev->dev per Milton's observation]
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Milton Miller <miltonm@bga.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>

In drivers/pci/xen-pcifront.c the xen/xenbus.h header is included twice -
once is enough.
Signed-off-by: NJesper Juhl <jj@chaosbits.net>
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

The BKL was pushed into this function when it was converted to use the
unlocked_ioctl interface, but nothing that the function touches is
actually protected by the BKL.  So just remove the BKL entirely, so that
we finally can get a realistic system build without the BKL being
enabled at all.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Allocate space from the highest-address PCI bus resource first, then work
downward.

Previously, we looked for space in PCI host bridge windows in the order
we discovered the windows.  For example, given the following windows
(discovered via an ACPI _CRS method):

    pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff]
    pci_root PNP0A03:00: host bridge window [mem 0x000c0000-0x000effff]
    pci_root PNP0A03:00: host bridge window [mem 0x000f0000-0x000fffff]
    pci_root PNP0A03:00: host bridge window [mem 0xbff00000-0xf7ffffff]
    pci_root PNP0A03:00: host bridge window [mem 0xff980000-0xff980fff]
    pci_root PNP0A03:00: host bridge window [mem 0xff97c000-0xff97ffff]
    pci_root PNP0A03:00: host bridge window [mem 0xfed20000-0xfed9ffff]

we attempted to allocate from [mem 0x000a0000-0x000bffff] first, then
[mem 0x000c0000-0x000effff], and so on.

With this patch, we allocate from [mem 0xff980000-0xff980fff] first, then
[mem 0xff97c000-0xff97ffff], [mem 0xfed20000-0xfed9ffff], etc.

Allocating top-down follows Windows practice, so we're less likely to
trip over BIOS defects in the _CRS description.

On the machine above (a Dell T3500), the [mem 0xbff00000-0xbfffffff] region
doesn't actually work and is likely a BIOS defect.  The symptom is that we
move the AHCI controller to 0xbff00000, which leads to "Boot has failed,
sleeping forever," a BUG in ahci_stop_engine(), or some other boot failure.

Reference: https://bugzilla.kernel.org/show_bug.cgi?id=16228#c43
Reference: https://bugzilla.redhat.com/show_bug.cgi?id=620313
Reference: https://bugzilla.redhat.com/show_bug.cgi?id=629933Reported-by: NBrian Bloniarz <phunge0@hotmail.com>
Reported-and-tested-by: NStefan Becker <chemobejk@gmail.com>
Reported-by: NDenys Vlasenko <dvlasenk@redhat.com>
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

This is a port of the 2.6.18 Xen PCI front driver with fixes
to make it build under 2.6.34 and later (for the full list of
changes: git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen.git
historic/xen-pcifront-0.1). It also includes the fixes
to make it work properly.

[v2: Updated Kconfig, removed crud, added Reviewed-by]
[v3: Added 'static', fixed grant table leak, redid Kconfig]
[v4: Added one more 'static' and removed comments]
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: NStefano Stabellini <stefano.stabellini@eu.citrix.com>
Reviewed-by: NJan Beulich <JBeulich@novell.com>

Introduce an override for the arch_[teardown|setup]_msi_irqs
that can be utilized to fallback to the default arch_* code.

If a platform wants to utilize the code paths defined
in driver/pci/msi.c it has to define HAVE_DEFAULT_MSI_TEARDOWN_IRQS
or HAVE_DEFAULT_MSI_SETUP_IRQS. Otherwise the old mechanism
of over-ridding the arch_* works fine.
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: x86@kernel.org

In preperation of modularizing Xen-pcifront the pci_walk_bus
needs to be exported so that the xen-pcifront module can walk
call the pci subsystem to walk the PCI devices and claim them.
Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org> [http://marc.info/?l=linux-pci&m=126149958010298&w=2]

The patch below updates broken web addresses in the kernel
Signed-off-by: NJustin P. Mattock <justinmattock@gmail.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Dimitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Acked-by: NBen Pfaff <blp@cs.stanford.edu>
Acked-by: NHans J. Koch <hjk@linutronix.de>
Reviewed-by: NFinn Thain <fthain@telegraphics.com.au>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

* Rename shpchp_wq to shpchp_ordered_wq and add non-ordered shpchp_wq
  which is used instead of the system workqueue.  This is to remove
  the use of flush_scheduled_work() which is deprecated and scheduled
  for removal.

* With cmwq in place, there's no point in creating workqueues lazily.
  Create both shpchp_wq and shpchp_ordered_wq upfront.

* Include workqueue.h from shpchp.h.
Signed-off-by: NTejun Heo <tj@kernel.org>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>

* Rename pciehp_wq to pciehp_ordered_wq and add non-ordered pciehp_wq
  which is used instead of the system workqueue.  This is to remove
  the use of flush_scheduled_work() which is deprecated and scheduled
  for removal.

* With cmwq in place, there's no point in creating workqueues lazily.
  Create both pciehp_wq and pciehp_ordered_wq upfront.

* Include workqueue.h from pciehp.h.
Signed-off-by: NTejun Heo <tj@kernel.org>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Not all hardware vendors hook up the PME line for legacy PCI devices,
meaning that wakeup events get lost. The only way around this is to poll
the devices to see if their state has changed, so add support for doing
that on legacy PCI devices that aren't part of the core chipset.
Acked-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

It's helpful to have some extra PCI power management functions available to
platform code, so move the declarations to an exported header.
Acked-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

I missed the closing parenthesis on "(PCI address ...)".
Acked-by: NArnd Bergmann <arnd@arndb.de>
Reported-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Previously we had to have CONFIG_PCI_DEBUG=y or CONFIG_DYNAMIC_DEBUG=y
to turn on this printk, but I think the IDs are valuable enough that it's
worth putting them in the log always.
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Replace EXTRA_CFLAGS with ccflags-y.
Signed-off-by: Nmatt mooney <mfm@muteddisk.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

These are already defined in pcilib's pci/header.h but not in kernel's
linux/pci_regs.h.  Copy them to avoid using magic numbers.
Signed-off-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

A long time ago I worked on a RHEL5 bug in which kdump hung during boot
on a set of systems.  The systems hung because they never received timer
interrupts during calibrate_delay.  These systems also all had Opteron
processors on a hypertransport bus, bridged to a pci bus via an Nvidia
MCP55 northbridge chip.  After much wrangling I managed to learn from
Nvidia that they have an undocumented register in some versions of that
chip which control how legacy interrupts are send to the cpu complex
when the ioapic isn't active.  Nvidia defaults this register to only
send legacy interrupts to the BSP, so if kdump happens to boot on an AP,
we never get timer interrupts and boom.  I had initially used this quirk
as a workaround, with my intent being to move apic initalization to an
earlier point in the boot process, so the setting of the register would
be irrelevant.  Given the work involved in doing that however, the
fragile nature of the apic initalization code, and the fact that, over
the 2 years since we found this bug, the MCP55 is the only chip which
seems to have this issue, I've figure at this point its likely safer to
just carry the quirk around.  By setting the referenced bits in this
hidden register, interrupts will be broadcast to all cpus when the
ioapic isn't active on the above described systems.
Acked-by: NSimon Horman <horms@verge.net.au>
Acked-by: NVivek Goyal <vgoyal@redhat.com>
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

There is a design issue related to PCIe AER and _OSC that the BIOS
may be asked to grant control of the AER service even if some
Hardware Error Source Table (HEST) entries contain information
meaning that the BIOS really should control it.  Namely,
pcie_port_acpi_setup() calls pcie_aer_get_firmware_first() that
determines whether or not the AER service should be controlled by
the BIOS on the basis of the HEST information for the given PCIe
port.  The BIOS is asked to grant control of the AER service for
a PCIe Root Complex if pcie_aer_get_firmware_first() returns 'false'
for at least one root port in that complex, even if all of the other
root ports' HEST entries have the FIRMWARE_FIRST flag set (and none
of them has the GLOBAL flag set).  However, if the AER service is
controlled by the kernel, that may interfere with the BIOS' handling
of the error sources having the FIRMWARE_FIRST flag.  Moreover,
there may be PCIe endpoints that have the FIRMWARE_FIRST flag set in
HEST and are attached to the root ports in question, in which case it
also may be unsafe to ask the BIOS for control of the AER service.

For this reason, introduce a function checking if there's at least
one PCIe-related HEST entry with the FIRMWARE_FIRST flag set and
disable the native AER service altogether if this function returns
'true'.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Get rid of init_MUTEX[_LOCKED]() and use sema_init() instead.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

quiet the warning about use of uninitialized e_src in
aer_isr()  e_src is initialized by get_e_source()
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

All operations in the pci procfs ioctl functions are
atomic, so no lock is needed here.

Also add a compat_ioctl method, since all the commands
are compatible in 32 bit mode.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: linux-pci@vger.kernel.org
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Indent the branch of an if.

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r disable braces4@
position p1,p2;
statement S1,S2;
@@

(
if (...) { ... }
|
if (...) S1@p1 S2@p2
)

@script:python@
p1 << r.p1;
p2 << r.p2;
@@

if (p1[0].column == p2[0].column):
  cocci.print_main("branch",p1)
  cocci.print_secs("after",p2)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>