Based on BenH's earlier work, this is a new version of the EMAC driver
for the built-in ethernet found on PowerPC 4xx embedded CPUs.  The
same ASIC is also found in the Axon bridge chip.  This new version is
designed to work in the arch/powerpc tree, using the device tree to
probe the device, rather than the old and ugly arch/ppc OCP layer.

This driver is designed to sit alongside the old driver (that lies in
drivers/net/ibm_emac and this one in drivers/net/ibm_newemac).  The
old driver is left in place to support arch/ppc until arch/ppc itself
reaches its final demise (not too long now, with luck).

This driver still has a number of things that could do with cleaning
up, but I think they can be fixed up after merging.  Specifically:
	- Should be adjusted to properly use the dma mapping API.
Axon needs this.
	- Probe logic needs reworking, in conjuction with the general
probing code for of_platform devices.  The dependencies here between
EMAC, MAL, ZMII etc. make this complicated.  At present, it usually
works, because we initialize and register the sub-drivers before the
EMAC driver itself, and (being in driver code) runs after the devices
themselves have been instantiated from the device tree.
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Since we are adding requirement for the PHYLIB for this driver, there should be a select for that

Cc: Robin Getz <robin.getz@analog.com>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

 - add MDIO functions and register mdio bus
 - add phy abstraction layer (PAL) functions and use PAL API
 - test on STAMP537 board
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Acked-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Blackfin EMAC driver: add power management interface and change the bf537mac_reset to bf537mac_disable
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Acked-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Alex Landau writes in the forums:
 Previously, changing the MAC address (e.g. via ifconfig) resulted
 in a generic function to be called that only changed a variable in
 memory. This patch also updated the Blackfin MAC address registers
 to filter the correct new MAC.
Signed-off-by: NAlex Landau <lirsb@yahoo.com>
Signed-off-by: NMike Frysinger <michael.frysinger@analog.com>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Acked-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

- Update transceiver information in ethtool function
Signed-off-by: NSreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

- Added set_mac_address driver entry point
- Copying permanent mac address to dev->perm_addr
- Incorporated following review comments from Jeff
     - Converted the macro to a function and removed call to memset
     - regarding function naming convention, for all callbacks and entry points
       will have 's2io_' prefix and helper functions will have 'do_s2io_' prefix.
Signed-off-by: NSreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Removed bimodal interrupt support - unused feature
Signed-off-by: NSivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

[also, trim trailing whitespace]

- Changed kmalloc+memset to k[zc]alloc as per Mariusz's patch
  <m.kozlowski@tuxland.pl>
Signed-off-by: NSivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

These have been superceded by the new ->get_sset_count() hook.
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NMichael Wu <flamingice@sourmilk.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is nicer than the MAC_FMT stuff.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the mac80211 based wireless drivers for the Intel
PRO/Wireless 3945ABG/BG Network Connection and Intel Wireless WiFi
Link AGN (4965) adapters.

[ Move driver into it's own directory -DaveM ]
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

[ Ported to napi_struct changes... -DaveM ]
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJesse Huang <jesse@icplus.com.tw>
Signed-off-by: NStefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For the operations
	get-tx-csum
	get-sg
	get-tso
	get-ufo
the default ethtool_op_xxx behavior is fine for all drivers, so we
permit op==NULL to imply the default behavior.

This provides a more uniform behavior across all drivers, eliminating
ethtool(8) "ioctl not supported" errors on older drivers that had
not been updated for the latest sub-ioctls.

The ethtool_op_xxx() functions are left exported, in case anyone
wishes to call them directly from a driver-private implementation --
a not-uncommon case.  Should an ethtool_op_xxx() helper remain unused
for a while, except by net/core/ethtool.c, we can un-export it at a
later date.

[ Resolved conflicts with set/get value ethtool patch... -DaveM ]
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We now have struct net_device_stats embedded in struct net_device,
and the default ->get_stats() hook does the obvious thing for us.

Run through drivers/net/* and remove the driver-local storage of
statistics, and driver-local ->get_stats() hook where applicable.

This was just the low-hanging fruit in drivers/net; plenty more drivers
remain to be updated.

[ Resolved conflicts with napi_struct changes and fix sunqe build
  regression... -DaveM ]
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDenis Cheng <crquan@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

It's been a useless no-op for long enough in 2.6 so I figured it's time to
remove it.  The number of people that could object because they're
maintaining unified 2.4 and 2.6 drivers is probably rather small.

[ Handled drivers added by netdev tree and some missed IRDA cases... -DaveM ]
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Code Optimization of s2io_isr function.
- Isr check using per device napi variable instead of driver global.
- Reduced from 3 to 1 if condition before check for processing packet receive
  packets.
- Implemented Jeff's comment to use synchronize_irq. Removed the isr_cnt
  variable as it became redundant.
- One time de assert the interrupts by writing all F's to the general_int_mask
  register instead of de asserting by clearing the source of interrupts with
  multiple writes which causes loss of interrupts (race conditions). It is
  entirely possible that before the driver has a chance to mask the asserted
  alarm bit, another alarm/traffic interrupt bit gets asserted as well. In
  this case Herc will keep the INTA line asserted and the bridge will not
  send a new Assert_INTA message upstream.

[ Resolved conflicts due to napi_struct changes... -DaveM ]
Signed-off-by: NSivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: NSantosh Rastapur <santosh.rastapur@neterion.com>
Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Added check to return from the traffic handling function, if the card status
  is DOWN.
- Implemented Jeff's comments on incorrect return value in s2io_poll function.
Signed-off-by: NSivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: NSantosh Rastapur <santosh.rastapur@neterion.com>
Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

- Removed the unused variable, intr_type, in device private structure.

[ Resolve conflicts with napi_struct changes... -DaveM ]
Signed-off-by: NSivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: NSantosh Rastapur <santosh.rastapur@neterion.com>
Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Added support to poll entire set of device errors and alarams.
- A note on how device errors and alarms are handled:
- The adapter will automatically recover from uncorrectable ECC errors.
  Packets containing corrupted data will be dropped (not transmitted) or tagged
  as invalid before being passed to the host.
- The adapter cannot recover from any internal state machine errors. A state
  machine error requires a device reset.
- Any internal error that could potentially result in .store trampling.
  (undesirable PCI behaviour)is tagged as a "serious error". In such cases
  the adapter will give up its ability to be a bus master. In this situation
  the host will still be able to read internal device registers in order to
  generate an error report. A device reset is necessary to return to normal
  operation.
- In the event of a pcix data parity error, the adapter will automatically
  disable itself. Adapter_En will automatically transition from '1' to '0' and
  the adapter will enter its clean-up routine. Once the device has achieved
  quiescence, an adapter reset should be performed.
- Replaced alarm_intr_handler() with s2io_handle_errors().
- Added statistic counters to monitor the alarms.

[ Fix warnings wrt. do_s2io_chk_alarm_bit(), Callers pass in an
  "unsigned long long *" but the function takes a "u64 *" which is
  different on many 64-bit platforms. -DaveM ]
Signed-off-by: NSivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: NSantosh Rastapur <santosh.rastapur@neterion.com>
Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

- Added support to unmask entire set of device errors and alarams.
        Alarm interrupts are generated for a myriad of purposes, ranging from
  illegal operations or requests to internal state machine errors and
  uncorrectable data corruption errors. In several cases the adapter can
  recover gracefully from unexpected events; however, in some cases, a device
  reset may be necessary. This patch handles alarms generated by all the
  blocks within the device.

  The adapter generates the following types of alarms:
        1. Link state transitions (local/remote fault) or other link-related
           problems.
        2. Problems with any device peripherals, including the EEPROM, FLASH,
           etc.
        3. Correctable ECC errors (single-bit errors) on internal data
           structures or frame data.
        4. Uncorrectable ECC errors (multi-bit errors) on internal data
           structures or frame data.
        5. State machine errors, which indicate that internal control
           structures have become corrupted.
        6. PCI related errors, including parity errors or illegal transactions.
        7. Other unexpected events.

- Implemented Jeff's review comments to use do_s2io_write_bits function to avoid
  duplicate codes.
Signed-off-by: NSivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: NSantosh Rastapur <santosh.rastapur@neterion.com>
Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

remove setup platform device from jazzsonic, which is done in arch code now
Signed-off-by: NThomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The sgiseeq driver is one of the few remaining users of the ancient
cache banging DMA API.  Replaced with the modern days DMA API.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The new microcode engine version is set to 1.1.0
Signed-off-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

add driver recognition for T3C rev board.
Signed-off-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Currently, the driver only tries up to 5 times (5us) to get the results
of a CQ context operation.  Testing has shown the chip can take as much
as 50us to return the response on SG_CONTEXT_CMD operations.  So we up
the retry count to 100 to cover high loads.
Signed-off-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The cxgb3 driver is incorrectly configuring the HW CQ context for CQ's
that use overflow-avoidance.  Namely the RDMA control CQ.  This results
in a bad DMA from the device to bus address 0.  The solution is to set
the CQ_ERR bit in the context for these types of CQs.
Signed-off-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Qualify toggling of xgmac tx enable with not getting pause frames,
we might not make forward progress because the peer is sending
lots of pause frames.
Signed-off-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Clear pciE PEX errors late at module load time.
Log details when PEX errors occur.
Signed-off-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Update firmware version.
Allow the driver to be up and running with older FW image
Signed-off-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Since E100 timer is 2HZ, use rounding to make timer occur on the
correct boundary.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>