Return the encoder id rather than a boolean.  This is needed
for differentiate between multiple DP bridge chips.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Settings in this table reflect the physical panel/connector rather
than the internal dig encoding.

v2: fix typo for DRM_MODE_CONNECTOR_VGA case.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

llano has fully routeable dig encoders similar to DCE3.2 while
ontario has a hardcoded mapping similar to DCE4.0.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The encoders are supposedly fully routeable, but changing the mapping
doesn't always seem to take.  Using a hardcoded mapping is much more
reliable.

Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=41366Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Tested-by: NSimon Farnsworth <simon.farnsworth@onelan.co.uk>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

DVOOutputControl checks the value of of bios scratch reg 3
on some tables and assumes the encoder is already enabled
if the DFP2_ACTIVE bit is set.  Clear that bit so the table
sets the DDIA enable bit properly.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

Need to add support for 4 crtcs when setting the possible crtcs
for the encoders.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

This is used during phy init to set up the phy for DP.  This may
fix DP problems on DCE3.2 cards.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Certain revisions of the vbios on DCE3.2 cards have a bug
in the transmitter control table which prevents duallink from
being enabled properly on some cards.  The action switch statement
jumps to the wrong offset for the OUTPUT_ENABLE action.  The fix
is to use the ENABLE action rather than the OUTPUT_ENABLE action
on the affected cards.  In fixed version of the vbios, both
actions jump to the same offset, so the change should be safe.
Reported-and-tested-by: NDave Airlie <airlied@redhat.com>
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

DP clock and lanes were not set properly for DP bridges.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Required for DPMS on some systems.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Need to set up the bridge for DDC prior to the
i2c over aux transaction.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

dp to vga bridges for example.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This should give us more reliable results if the table
is called before an active device is set.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The PHY was not initialized correctly after
ac89af1e since
the function bailed early as an encoder was not
assigned.  The encoder isn't necessary for PHY init
so just assign to 0 for init so that the table
is executed.
Reported-by: NAri Savolainen <ari.m.savolainen@gmail.com>
Tested-by: NAri Savolainen <ari.m.savolainen@gmail.com>
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

It only needs to be called once at startup, not for every
modeset.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

- reorganize the functions based on use
- clean up function naming
- rework link training to better match what we use internally
- add initial support for DP 1.2 (no MST yet)
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Required for proper operation with DP bridges.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Fusion hardware often has DP to VGA/LVDS/TMDS bridges to
handle non-DP encoders.  Internally we treat them mostly
like DP.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Used for dp1.2 support and for dp bridges.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

need to wait for the panel to power up.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

eDP is usually used as an LVDS replacement, so treat
it more like LVDS from the user perspective.

v2: encoder mode is always DP for eDP.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

In DP mode, the DP ref clock can come from PPLL, DCPLL, or ext clock,
depending on the asic.  The crtc virtual pixel clock is derived from
the DP ref clock.

- DCE4: PPLL or ext clock
- DCE5: DCPLL or ext clock

Setting ATOM_PPLL_INVALID will cause SetPixelClock to skip
PPLL/DCPLL programming and only program the DP DTO for the
crtc virtual pixel clock.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

agd5f: additional cleanups/fixes
Signed-off-by: NCédric Cano <ccano@interfaceconcept.com>
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

- set scaler table clears the interleave bit, need to
reset it in encoder quirks, this was already done for
pre-dce4.
- remove the interleave settings from set_base() functions
this is now handled in the encoder quirks functions, and
isn't technically part of the display base setup.
- rename evergreen_do_set_base() to dce4_do_set_base() since
it's used on both evergreen and NI asics.

Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=28182Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

This error is reported by cppcheck:
drivers/gpu/drm/radeon/radeon_encoders.c:1066: warning: Mutual exclusion over || always evaluates to true. Did you intend to use && instead?

It looks like cppcheck is correct, so fix this. No test was run.

Cc: David Airlie <airlied@linux.ie>
Reviewed-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NStefan Weil <weil@mail.berlios.de>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Force DVI mode if the user specifies radeon.audio=0.  The driver
doesn't handle HDMI mode properly in some cases.

Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=27731Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@gmail.com>

This avoids some issues in the current hdmi audio code for monitors
without audio.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Needed to tell which DIG encoders are HBR2 capable for DP 1.2.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The DVOOutputControl table was removed for DCE5.
DVOEncoderControl now handles everything.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The DAC1OutputControl table was removed for DCE5.
DAC1EncoderControl now handles everything.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

only fusion asics are dce4.1
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Works more like DCE4.0 despite what the docs say.
This fixes blank screen issues when changing crtc
routing due to incorrect crtc to dig mapping.

v2: only two DIGx blocks, routing is hardcoded
based on link.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>