We're currently not passing anything and this will make the card and so on
more discoverable.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The default WM8958 jack detection handler implements a full set of buttons
and also support for video detection. Support for multi-button jacks is
fairly system specific and will usually require some tuning for headsets
so simplify the implementation to only report a simple short to ground
button, leaving multi-button headsets to be handled by system specific
code.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The WM8958 has a different microphone bias architecture to WM8994 so needs
different configuration to WM8994. Support this in platform data.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Allow direct routing of the WM8958 microphone detection signal to a GPIO
to be used, saving the need to demux the interrupt.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

As bias level changes can be quite time consuming and the bias changes
for multiple devices aren't strongly tied to each other (if anything it
can be advantageous to bring different devices up together) we can improve
the state transition time for multi-component systems by running the bias
level changes for all the devices in parallel. This is very simple to
achieve using the kernel async functionality so use that to schedule the
work.

This should have no practical effect for the overwhelming majority of
systems which have a single DAPM context - we'll bounce into another
thread to do the bias level change but otherwise everything will happen
in exactly the same order as it did before.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

We can get the card from the DAPM context so don't bother passing it as
an argument.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The microphone detection functionality requires a clock to work. In any
non-detection case where the MICBIAS is enabled CLK_SYS will be needed
anyway so there is no negative impact on power consumption.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The microphone detection functionality requires a clock to work. In any
non-detection case where the MICBIAS is enabled CLK_SYS will be needed
anyway so there is no negative impact on power consumption.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

So they show up in codec_reg.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Some systems wish to use jacks as wake sources. Provide a wake flag in the
GPIO configuration which causes the driver to enable the IRQ as a wake
source.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The only thing that should ever be calling this is soc-core and that is
built as part of the same module so doesn't need the export.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Pulseaudio doesnt work with current driver and it was root caused to absense of
hw_params function and malloc_pages in it.
This patch adds this and allows pa to work fine with these drivers
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NHarsha Priya <priya.harsha@intel.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch removes the old method of soc-audio device creation in mfld machine
and makes use of new soc_register_card API to register the card
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NHarsha Priya <priya.harsha@intel.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The tlv scale is defined as (min, step, mute). The mute is not supported here so
put the value to 0
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NHarsha Priya <priya.harsha@intel.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch makes the DMIC dynamically connect to TX Mux, earlier code had
erroneously made this as static path
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NHarsha Priya <priya.harsha@intel.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch makes the codec playback rails (headset and speaker) depend on
actual pins they control. This enables better power management of the codec
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NHarsha Priya <priya.harsha@intel.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The WM8903 interrupts are clear on read so if the WM8903 detection is
enabled from platform data when the IRQ is in use (rather than using a
direct signal from a GPIO) status may be lost during startup. Help users
spot this misconfiguration by adding a WARN_ON().
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

With the appropriate MODULE_ALIAS in place, the audio modules will be
automatically loaded; there is no longer a need for manual modprobes.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Harmony has both an external mic (a regular mic jack) and an internal mic
(a 0.1" two-pin header on the board).

The external mic is connected to the WM8903's IN1L pin, and is supported
by the current driver.

The internal mic is connected to the WM8903's IN1R pin, and is not supported
by the current driver.

It appears that no Harmony systems were shipped with any internal mic
connected; users were expected to provide their own. This makes the
internal mic connection less interesting.

The WM8903's Mic Bias signal is used for both of these mics. For each mic,
a GPIO drives a transistor which gates whether the mic bias signal is
actively connected to that mic, or isolated from it.

The dual use of the mic bias for both mics makes a general-purpose complete
implementation of mic detection using the mic bias complex. So, for
simplicity, the internal mic is currently ignored by the driver.

This patch configures the relevant GPIOs to enable the mic bias connection
to the external mic, and disable the mic bias connection to the internal
mic. Note that in practice, this is the default state if these GPIOs aren't
configured.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

* Add jack definition for mic jack
* Request wm8903 to enable mic detection
* Force mic bias on, since it's required for mic detection
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

If a widget has been force enabled then not only do we need to keep the
widget itself enabled, we also need to keep any supplies the widget
requires enabled. The user could force all the individual widgets on but
this requires too much knowledge of device internals.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

On WM8994 revision D and earlier ensure proper playback robustness
as some rare use cases can trigger issues.
Signed-off-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

Ensure that on disabling certain registers such as AIF1DAC1L,
AIF1DAC1R etc. the AIF1CLK and AIF2CLK remain enabled.  Similarly
when enabling those registers, AIF1CLK and AIF2CLK will remain
disabled.
Signed-off-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

The mic detection HW should be enabled when either mic or short detection
is required, not when only both are required.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

* There is no hysteresis enable field in the current datasheet.
* Mic detection threshold field is only 2 bits wide.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

It is safe to use sleeping gpio in snd_soc_jack_gpio_detect as it is not
called from interrupt context. This avoids WARN_ON from __gpio_get_value
if sleeping gpio is registered for jack.
Signed-off-by: NJarkko Nikula <jhnikula@gmail.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch modifies the mfld_machine to use the new jack apis for adding the
voltage zones for jack type detection. It also modifed TI sn95031 codec driver
to use these new apis
Signed-off-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NHarsha Priya <priya.harsha@intel.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This makes no real difference compared to the write sequencer sequence
that was previously used but can run without a clock being provided.
Also remove the write sequencer support code as this was the last use
of it.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The write sequencer sequencer sequence takes longer than is desirable
as it brings up a full playback path which is not required at this
point. Open coding the sequence cuts the startup time by two thirds.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>