If a MAC address for a key table entry is flagged with the
multicast bit (0x01), indicate to the hardware that multicast
lookup instead of unicast lookup should be used. The multicast
bit itself never makes it to the actual keytable entry register,
as it is shifted out.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Acked-by: NGábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This reverts commit a2064b7a.

when CONFIG_IWLAGN=n:

drivers/net/wireless/iwlwifi/iwl-rx.c:254: error: 'struct iwl_priv' has no member named '_agn'
drivers/net/wireless/iwlwifi/iwl-rx.c:303: error: 'struct iwl_priv' has no member named '_agn'
drivers/net/wireless/iwlwifi/iwl-rx.c:304: error: 'struct iwl_priv' has no member named '_agn'
drivers/net/wireless/iwlwifi/iwl-rx.c:305: error: 'struct iwl_priv' has no member named '_agn'
drivers/net/wireless/iwlwifi/iwl-rx.c:306: error: 'struct iwl_priv' has no member named '_agn'

and many more.

Conflicts:

	drivers/net/wireless/iwlwifi/iwl-agn-debugfs.c
	drivers/net/wireless/iwlwifi/iwl-debugfs.c
	drivers/net/wireless/iwlwifi/iwl-dev.h
	drivers/net/wireless/iwlwifi/iwl-rx.c
Reported-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove suspicious register write as the reg variable is never filled
with an TX_SW_CFG2 associated value before.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>

In case of mcs rates txrate->idx contains the mcs index to be used for
transmission. Previously the mcs values dedicated for legacy rates where
used for mcs transmissions which resulted in the use of mcs 0 in a number
of cases (e.g. for all mcs rates >= 15 as rt2x00 does not register legacy
rates with indexes >= 15).
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>

Update TX_SW_CFG initvals for 305x SoC to match with the appropriate
legacy driver.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>

Use the IEEE80211_TX_CTL_STBC flag to determine the
correct value to be used for the STBC field in the
TX descriptor
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>

Disable TX STBC for 1 stream devices as a minimum of 2 streams is needed for TX STBC.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>

Closer inspection of the legacy Ralink driver reveals that in case of HT40+
or HT40- we must adjust the frequency settings that we program to the device.
Implement the same adjustment in the rt2x00 code.

With this HT40 seems to work for all devices supported by rt2800pci and
rt2800usb.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>

Latest versions of the Ralink rt2800 family drivers use 0 as the token value,
not 0xff.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>

This prevents us having common code depend on PCI or USB specific code.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>

Instead of parsing the EEPROM information, use the flag that was set during
device initialization.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>

Needed later for PCI-express specific code in rt2800pci.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>

There is no point on having them separated across 3 files.
At the same time rename USB_CYC_CFG to its proper name US_CYC_CNT
(as per the datasheet).
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>

There is no evidence, either in adapters or in the Ralink code, that such
a device actually exists. All so-call RT2870 adapter identify themselves
as RT2860.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>

The beacon writing functions of rt2800pci and rt2800usb are now identical.
Move them to rt2800lib to only have one central function.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>

There is no need to force the separation between a buffer USB vendor
request that does fit the CSR cache and one that doesn't onto the
callers. This is something that the rt2x00usb_vendor_request_buff
function can figure out by itself.
Combine the rt2x00usb_vendor_request_buff and
rt2x00usb_vendor_request_large_buff functions into a single one, as
both of them were equivalent for small buffers anyway.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>

The recent changes to skb handling introduced a bug in the rt2800usb
TX descriptor writing whereby the length of the USB packet wasn't
calculated correctly.
Found via code inspection, as the devices themselves didn't seem to mind.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>

Instead of fiddling with the skb->data pointer and thereby risking
out of bounds accesses, properly reserve the space needed in an
skb for descriptors.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>

For rt2800 reverse the calling order of rt2x00pci_write_data and
rt2800pci_write_data. Currently rt2800pci_write_data calls rt2x00pci_write_data
as there can be only 1 driver callback function specified by the driver.
Reverse this calling order by introducing a new driver callback function,
called write_tx_datadesc, which is called from the bus-specific write_tx_data
functions.
Preparation for futher cleanups in the skb data handling of rt2x00.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>

Not all the devices require a TX descriptor to be written (i.e. rt2800
device don't require them). Push down the creation of the TX descriptor
to the device drivers so that they can decide for themselves whether
a TX descriptor is to be created.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>

Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The 5GHz bands were scanned without the proper IE's in place, preventing
proper 5GHz scanning. This patches fixes the problem by storing a pointer
to the scan request (with the IE's) for all iterations of scan.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A fixed 1 mbps rate was used for the PSM entry/exit null-func frames. Fix this
by using the basic rates instead.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The core wl1271 module can also be used with SDIO, so it should not depend on
SPI_MASTER.
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The mac80211 changes to idle almost immediately after transmitting some
frames, such as deauth etc. When going to idle, the wl1271 is disconnected,
which causes TX frames already on buffers, but not yet transmitted, to be
deleted.

To make sure deauth frames reach the air, allow the TX buffers to flush
before proceeding to idle.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NTeemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As there is more and more stuff triggered by going in and out of idle,
create a separate function for handling that.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NTeemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The wl1271 uses a session counter in CMD_JOIN and TX frame descriptors. This
counter is used to determine which frames to drop when the CMD_JOIN is
executed.

The driver executes CMD_JOIN multiple times upon association and sometimes
disassociation, and we don't want any frames to get lost.

Fix this by incrementing the session counter only when leaving idle (not every
CMD_JOIN as before.) Also, remove the TX flush flag from the CMD_JOIN options.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NTeemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We dereference "wmi" on the line before and also when we initialize "ah".
This check has always been after a dereference since the first commit a
couple months ago.  Looking through the code, it looks like "wmi" can't
actually be null here so I just removed the check.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Acked-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use memdup_user when user data is immediately copied into the
allocated region.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression from,to,size,flag;
position p;
identifier l1,l2;
@@

-  to = \(kmalloc@p\|kzalloc@p\)(size,flag);
+  to = memdup_user(from,size);
   if (
-      to==NULL
+      IS_ERR(to)
                 || ...) {
   <+... when != goto l1;
-  -ENOMEM
+  PTR_ERR(to)
   ...+>
   }
-  if (copy_from_user(to, from, size) != 0) {
-    <+... when != goto l2;
-    -EFAULT
-    ...+>
-  }
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The rx status length should also be taken into account while
validating the length of a received frame.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Skip the rx status portion in skb->data before accessing ieee80211
frame header.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath9k_rx_skb_preprocess() needs only ieee80211 frame header,
pass only frame headers instead of skb to that function. Also
remove ineffective frame dump in ath9k_process_rate().
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A bunch of data structures are present in the
common module, which are internal to ath9k.
Move them to ath9k.h
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch relocates RX processing code from the
common module to ath9k. This reduces the size
of the common module which is also used by ath9k_htc.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The C99 specification states in section 6.11.5:

The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Acked-by: NReinette Chatre <reinette.chatre@intel.com>
Acked-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

To enable it we now disable and re-enable the PHY chips
after TX IQ calibration.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When sending action frames, we want to verify
that we do that on the correct channel. However,
checking the channel type in addition can get in
the way, since the channel type could change on
the fly during an association, and it's not
useful to have the channel type anyway since it
has no effect on the transmission. Therefore,
make it optional to specify so that if wanted,
it can still be checked, but is not required.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since we have sysfs to manually set the ANI levels, we should print errors to
the kernel log if the values are out of bounds.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>