Sometimes, ARQ overflows are a big deal and tell us that the
firmware/hardware/driver/something is having problems. But normally
they're no big deal. To assist in assessing this, add a counter to
our Ethtool stats. A handful of ARQ overflows during VF init is no
problem. A large, ever-growing number indicates that Something Bad is
happening.

Change-ID: Ie5348bfbc8a54a890559cb00279c28d976a55096
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We were not doing write-back on interrupt throttle for Legacy case in X722.
This patch fixes that, so we do WB_ON_ITR for Legacy as well. Plus the issue
that we should still be setting NO_ITR if we are touching the DYN_CTLN register
since we do not want to change ITR setting here.

Change-ID: I5db8491ee1544118a389db839cecc93e1bbc480e
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

lan_vsi_idx and lan_vsi_id are assigned to u16 data sized variables but
declared in u8. This patch fixes the width of the datatype.

Change-ID: If4bcbcc7d32f2b287c51cb33d17879691258dce2
Signed-off-by: NPandi Kumar Maharajan <pandi.maharajan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Bump AQ minor version to 1.5 for new FW features.

Change-ID: I5a790f7f519a2a8921aaa1c5663727dd1897ffec
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Acked-by: NKevin Scott <kevin.c.scott@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add the new AQ command and struct for managing a thermal sensor.

Change-ID: I6f5631839a0f3dca352a6c222f1269a960e2310a
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add the new Cisco VXLAN-GPE cloud tunnel type for the Add Cloud Filter
and UDP tunnel AQ commands.

Change-ID: I2c093c7d79726c7fca08a36e5c63581a905da3d2
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Acked-by: NKevin Scott <kevin.c.scott@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add the new Set Switch Config AdminQ command, and mark the L2 Filter
bit as deprecated in the Add VEB command.

Change-ID: I5b24790f14c56f0ddf3f70df1e486844146b039f
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Acked-by: NKevin Scott <kevin.c.scott@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add flags to MAC allocation requests to signify that the MAC VLAN filters
should come from the shared resource pool rather than the dedicated PF
resource pools.

Change-ID: I4c2da64c01856edcb0982bc4aab75c5a91047a7a
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Acked-by: NKevin Scott <kevin.c.scott@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change has been made with the goal that kernel functions should
return something more descriptive than -1 on failure.

A variable `err` has been introduced for storing error codes.

The return value of kzalloc on failure should return a -1 and not a
-ENOMEM. This was found using Coccinelle. A simplified version of
the semantic patch used is:

//<smpl>
@@
expression *e;
identifier l1;
@@

e = kzalloc(...);
if (e == NULL) {
...
goto l1;
}
l1:
...
return -1
+ -ENOMEM
;
//</smpl

Furthermore, set `err` to -ENOMEM on failure of alloc_netdev(), and to
-ENODEV on failure of register_netdev() and probe_irq_off().

The single call site only checks that the return value is not 0,
hence no change is required at the call site.
Signed-off-by: NAmitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Also print an error message incase we do have to reconfigure as this
should no longer happen anymore due to ethtool changes. If it somehow
does occur, user should be made aware of it.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We need that for a custom hardware that needs the reverse reset
sequence.
Signed-off-by: NBernhard Walle <bernhard@bwalle.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce a macro which helps adding new 40NM EPHY entries and reduces the
amount of boilerplate code.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver is BCM7xxx, we were missing an additional X in the constant naming,
fix that to be consistent.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There was a workaround partially implemented for the 82576 that is needed
in order for VLAN tag stripping to function correctly.  The original code
had side effects that would make it so the workaround was active on all
MACs.  I have updated the code so that the workaround is enabled, but
limited to the 82576, or activated if we exceed the available unicast
addresses.

The workaround has a side effect of mirroring all of the traffic outgoing
from the VFs back to the PF.  As such it is not recommended to use the
82576 in promiscuous mode as it will take a performance hit, though this is
now consistent with the performance as seen on the out-of-tree igb driver.

I also limited the scope of the UTA bits all being set to only when the
VMOLR register is enabled.  This should limit the effects of the UTA
register so that we don't pick up any excess traffic unless promiscuous
mode has been enabled on the PF, whereas before the PF would have ended up
in something equivalent to unicast promiscuous mode with VLAN filtering
otherwise.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change makes it so that we can use the bridge utility to add a FDB
entry for the PF to an igb port.  By doing this we can enable the VFs to
talk to virtual ports residing on top of the PF.

In addition this should also address issues with MACVLANs trying to reside
on top of the PF as well as they would have had similar issues when added
to the PF with SR-IOV enabled.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch drops several checks that we dropped from ixgbe some ago.  It
should not be possible for us to be called with either of the conditional
statements returning true so we can just drop them from the hot-path.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change fixes things so that we can fully support SR-IOV or the
recently added NTUPLE filtering while allowing support for VLAN promiscuous
mode.  By making this change we are able to support possible scenarios such
as SR-IOV with the PF connected to a Linux bridge hosting other VMs.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is meant to clean-up the configuration of the VF port based VLAN
configuration.  The original logic was a bit muddled and had some
undesirable side effects such as VLANs being either completely stripped
from the port or VLANs being left when they shouldn't be.  The idea behind
this code is to avoid any events such as spurious spoof notifications when
we are removing one VLAN tag and replacing it with another.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change makes it so that we can merge the configuration of the VLVF
registers into the setting of the VFTA register.  By doing this we simplify
the logic and make use of similar functionality that we have already added
for ixgbe making it easier to maintain both drivers.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch makes it so that we always add VLAN 0.  This is important as we
need to guarantee the PF can receive untagged frames in the case of SR-IOV
being enabled but VLAN filtering not being enabled in the kernel.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The RLPML registers already take the size of VLAN headers into account when
determining the maximum packet length.  This is called out in EAS documents
for several parts including the 82576 and the i350.  As such we can drop
the addition of size to the value programmed into the RLPML registers.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since the igb driver is using page based receive there is no point in
limiting the Rx capabilities of the device.  The driver can receive 9K
jumbo frames at all times.  The only changes needed due to MTU changes are
updates for the FIFO sizes and flow-control watermarks.

Update the maximum frame size to reflect the 9.5K limitation of the
hardware, and replace all instances of max_frame_size with
MAX_JUMBO_FRAME_SIZE when referring to an Rx FIFO or frame.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch starts the clean-up process on the VFTA configuration.
Specifically in this patch I attempt to address and simplify several items
while also updating the code to bring it more inline with what is already
in ixgbe.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Drop a bunch of hand written byte swapping code in favor of just doing the
byte swapping ourselves.  The registers are little endian registers storing
a big endian value so if we read the MAC address array as little endian
then we will get the CPU registers into the proper layout.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The driver shouldn't just give up if it fails to get the hardware
mailbox lock. This can happen in a situation where the PF-VF
communication channel is heavily loaded and causes complete
communications failure between the PF and VF drivers.

Add a counter and a delay. The driver will now retry ten times, waiting
one millisecond between retries.
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

By the commit 72ddef05 ("igb: Fix oops caused by missing queue
pairing"), the IGB_FLAG_QUEUE_PAIRS flag can now be set when changing the
number of queues by "ethtool -L", but it is never cleared unless the igb
driver is reloaded.
This patch clears it if queue pairing becomes unnecessary as a result of
"ethtool -L".
Signed-off-by: NShota Suzuki <suzuki_shota_t3@lab.ntt.co.jp>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If VFs are enabled (max_vfs >= 1), both max_rss_queues and
adapter->rss_queues are set to 2 in the case of e1000_82576.
In this case, IGB_FLAG_QUEUE_PAIRS is always set in the default block as a
result of fall-through, thus setting it in the e1000_82576 block is not
necessary.
Signed-off-by: NShota Suzuki <suzuki_shota_t3@lab.ntt.co.jp>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

All users now pass false, so we can remove it, and remove the code that
 was conditional upon it.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is an opportunity to bulk free SKBs during reclaiming of
resources after DMA transmit completes in ixgbe_clean_tx_irq.  Thus,
bulk freeing at this point does not introduce any added latency.

Simply use napi_consume_skb() which were recently introduced.  The
napi_budget parameter is needed by napi_consume_skb() to detect if it
is called from netpoll.

Benchmarking IPv4-forwarding, on CPU i7-4790K @4.2GHz (no turbo boost)
 Single CPU/flow numbers: before: 1982144 pps ->  after : 2064446 pps
 Improvement: +82302 pps, -20 nanosec, +4.1%
 (SLUB and GCC version 5.1.1 20150618 (Red Hat 5.1.1-4))

Joint work with Alexander Duyck.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We should validate the port setting that we got from the user and check
if it's what we've set it to (PORT_OTHER), also add explanation that
ignoring advertising is good as long as we don't have autonegotiation.
Signed-off-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAndrew F. Davis <afd@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The TI TLK10x Ethernet PHYs are similar in the interrupt relevant
registers and so are compatible with the DP83848x devices already
supported.
Signed-off-by: NAndrew F. Davis <afd@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reorganize code by moving the desired interrupt mask definition
out of function. Also rearrange the enable/disable interrupt function
to prevent accidental over-writing of values in registers.
Signed-off-by: NAndrew F. Davis <afd@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After acquiring National Semiconductor, TI appears to have
changed the Vendor Model Number for the DP83848C PHYs,
add this new ID to supported IDs.
Signed-off-by: NAndrew F. Davis <afd@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a helper macro for defining dp83848 compatible phy devices.
Update copyright info.
Signed-off-by: NAndrew F. Davis <afd@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The EVB (virtual bridge) functionality should be disabled on older BE3
and Lancer chips if SR-IOV is disabled in the NIC's BIOS. This setting
is identified by the zero value of total VFs reported by the card.
The GET_HSW_CONFIG command cannot be used as it is not supported by
these older chipset's FW.

v2: added the comment

Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Padmanabh Ratnakar <padmanabh.ratnakar@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: NIvan Vecera <ivecera@redhat.com>
Acked-by: NSathya Perla <sathya.perla@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for MICREL KSZ8795CLX Integrated 5-Port, 10-/100-Managed
Ethernet Switch with Gigabit GMII/RGMII and MII/RMII interfaces.
Signed-off-by: NHelmut Buchsbaum <helmut.buchsbaum@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Prepare creating SPI reads and writes for other switch families.
The KS8995 family uses the straight forward
	<8bit CMD><8bit ADDR>
sequence.
To be able to support KSZ8795 family, which uses
	<3bit CMD><12bit ADDR><1 bit TR>
make the SPI command creation chip variant dependent.
Signed-off-by: NHelmut Buchsbaum <helmut.buchsbaum@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When using device tree it is no more possible to reset the PHY at board
level. Furthermore, doing in the driver allows to power down the switch
when it is not used any more.

The patch introduces a new optional property "reset-gpios" denoting an
appropriate GPIO handle, e.g.:

reset-gpios = <&gpio0 46 GPIO_ACTIVE_LOW>
Signed-off-by: NHelmut Buchsbaum <helmut.buchsbaum@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>