The struct is part of the userspace interface and can not use
bitfields.  This patch replaces the bitfields with a __u32 'control'
word and provides access macros to set the bits.
Signed-off-by: NKristian Høgsberg <krh@redhat.com>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

It's a low-impact design, that just makes suspend/resume look like
a bus reset to the upper level drivers, but it should be sufficient.
Signed-off-by: NKristian Høgsberg <krh@redhat.com>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

The attribute /sys/bus/scsi/devices/*:*:*:*/ieee1394_id, as generated by
the old sbp2 driver, is typically used to create persistently named
links in /dev/disk/by-id.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NKristian Høgsberg <krh@redhat.com>

With "modprobe sbp2 long_ieee1394_id=y", the format of
/sys/bus/scsi/devices/*:*:*:*/ieee1394_id is changed from e.g.
0001041010004beb:0:0 to 0001041010004beb:00042c:0000.

The longer format fully conforms to object identifier sizes as per
SAM(-2...4) and reflects what the SAM target port identifier is meant to
contain:  A Discovery ID allegedly specified by ISO/IEC 13213:1994 ---
however there is no such thing; the authors of SAM probably meant
Directory ID).  Especially target nodes with multiple dynamically added
targets may use Directory IDs to persistently identify target ports.

The new format is independent of implementation details of nodemgr.
Thus the same ieee1394_id attribute format can be implemented in the new
firewire stack.

The ieee1394_id is typically used to create persistently named links in
/dev/disk/by-id.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

struct csr1212_keyval.offset is relative to 0xffff f000 0000 rather than
0xffff f000 0400.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Deregister ccw device when device failure is detected during offline-
processing (e.g. when no last-path-gone indication was presented by
the hardware) to prevent the device from entering a non-recoverable
not-operational state.
Signed-off-by: NPeter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

We can't deregister disconnected and orphaned devices directly from
the online attribute's store method, but must take a detour.
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Commit c0affe9d doesn't work because
the host controller is being quirked not a PCI bridge.  This patch
reverts the commit, rename quirk_svw_msi() to quirk_disable_all_msi()
and use it instead.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: Matias Alejandro Torres <torresmat@gmail.com>
Cc: Greg K-H <greg@kroah.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix enable_irq_wake and disable_irq_wake symmetry in at91 pcmcia driver

disable_irq_wake call must be symmetric with enable_irq_wake.  This patch
fix that problem for the at91_pcmia driver.  It seems that this patch was
forgotten when we've fixed irq_wake symmetry in all at91 related drivers.
It was discussed in the "at91 drivers and [enable/disable]_irq_wake
(wrong?) usage" thread on the linux-arm-kernel mailing list.
Signed-off-by: NMarc Pignat <marc.pignat@hevs.ch>
Cc: David Brownell <david-b@pacbell.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The pseudo_palette has room for 16 entries only, but in truecolor mode, it
attempts to write 256.
Signed-off-by: NAntonino Daplas <adaplas@gmail.com>
Acked-by: NTero Roponen <teanropo@jyu.fi>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

drivers/sbus/char/flash.c does use macros VM_READ and such, needs to include
linux/mm.h.
Signed-off-by: NHorst H. von Brand <vonbrand@inf.utfsm.cl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The following patch fixes these section mismatch warnings:

WARNING: arch/arm/mach-at91/built-in.o(.text+0xdf4): Section mismatch: reference to .init.data:dk_nand_partition (between 'nand_partitions' and 'at91_leds_event')
WARNING: arch/arm/mach-at91/built-in.o(.text+0xbdc): Section mismatch: reference to .init.data:ek_nand_partition (after 'nand_partitions')
WARNING: arch/arm/mach-at91/built-in.o(.text+0xbdc): Section mismatch: reference to .init.data:ek_nand_partition (between 'nand_partitions' and 'ads7843_pendown_state')
WARNING: arch/arm/mach-at91/built-in.o(.text+0xbdc): Section mismatch: reference to .init.data:ek_nand_partition (after 'nand_partitions')
WARNING: arch/arm/mach-at91/built-in.o(.text+0xc28): Section mismatch: reference to .init.data:kb9202_nand_partition (after 'nand_partitions')
WARNING: arch/arm/mach-footbridge/built-in.o(.text+0xaa4): Section mismatch: reference to .init.data:cats_pci (between 'cats_pci_init' and 'ebsa285_leds_event')WARNING: arch/arm/mach-ixp2000/built-in.o(.text+0xb54): Section mismatch: reference to .init.text:ixp2000_init_irq (between 'ixdp2x00_init_irq' and 'ixdp2x00_irq_handler')
WARNING: arch/arm/mach-ixp23xx/built-in.o(.text+0x670): Section mismatch: reference to .init.text:ixp23xx_pci_common_init (between 'ixp23xx_pci_slave_init' and 'ixp23xx_pci_scan_bus')
WARNING: arch/arm/mach-ixp23xx/built-in.o(.text+0x890): Section mismatch: reference to .init.text:ixp23xx_init_irq (between 'ixdp2351_init_irq' and 'roadrunner_pci_preinit')
WARNING: arch/arm/mach-ixp23xx/built-in.o(.text+0x9a8): Section mismatch: reference to .init.text:ixp23xx_pci_preinit (after 'roadrunner_pci_preinit')
WARNING: arch/arm/mach-imx/built-in.o(__ksymtab+0x80): Section mismatch: reference to .init.text:imx_set_mmc_info (between '__ksymtab_imx_set_mmc_info' and '__ksymtab_set_imx_fb_info')
WARNING: arch/arm/mach-imx/built-in.o(__ksymtab+0x88): Section mismatch: reference to .init.text:set_imx_fb_info (after '__ksymtab_set_imx_fb_info')
WARNING: arch/arm/mach-sa1100/built-in.o(.text+0x1930): Section mismatch: reference to .init.data:neponset_port_fns (between 'neponset_probe' and 'assabet_leds_event')
WARNING: drivers/built-in.o(.text+0x3f100): Section mismatch: reference to .init.text:ps2_clear_input (between 'ps2_probe' and 'ps2_cmd_aborted')
WARNING: drivers/built-in.o(.text+0x3f1c8): Section mismatch: reference to .init.text:ps2_clear_input (between 'ps2_probe' and 'ps2_cmd_aborted')
WARNING: drivers/built-in.o(.text+0x4f988): Section mismatch: reference to .init.text:ps2_clear_input (between 'ps2_probe' and 'ps2_cmd_aborted')
WARNING: drivers/built-in.o(.text+0x4fa50): Section mismatch: reference to .init.text:ps2_clear_input (between 'ps2_probe' and 'ps2_cmd_aborted')
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Acked-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Must access the respective queue's dummy netdev instead of the port's netdev.
Signed-off-by: NThomas Klein <tklein@de.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Don't want IRQ on FIFO error because there is nothing useful to do with it.
But do want IRQ on duplex change.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This restores the previously removed netif_poll_enable call in e1000_open.
It's needed on all but the first call to e1000_open for a NIC as
e1000_close always calls netif_poll_disable.

netif_poll_enable can only be called safely if no polls have been
scheduled.  This should be the case as long as we don't enter our IRQ
handler.

In order to guarantee this we explicitly disable IRQs as early as possible
when we're probing the NIC.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Cc: "Kok, Auke" <auke-jan.h.kok@intel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

 If ioremap_nocache() is unfortunate enough to fail, the error code is not
set correctly leading to a false success from dfx_register().  This change
fixes the problem.
Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Driver was reading value from one register, setting bit and then
writing the wrong register.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Driver was not correctly setting up transmit descriptor when doing
VLAN tag insertion with checksum offload.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This code inherited from the sk98lin driver is incorrect on the Yukon2.
The GPHY_CTRL register values are specific to the internal PHY of the chip
and the values used were leftovers.
Driver was setting bit 13 which is now the INT polarity for the PHY!
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The -rt patch triggered a lockdep warning in the amba serial drivers, which never
shows up on UP kernels. On SMP systems this would trigger as well.

Release the port lock before calling tty_flip_buffer_push() and reacquire it after
the call. This matches the code in the 8250 serial driver.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Fix a error reported by newer versions of GCC.
error: static declaration of 'ks8695_reg' follows non-static declaration
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add data from zero-entropy random_writes directly to output pools to
avoid accounting difficulties on machines without entropy sources.

Tested on lguest with all entropy sources disabled.
Signed-off-by: NMatt Mackall <mpm@selenic.com>
Acked-by: N"Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix cast error in entropy extraction.
Add comments explaining the magic 16.
Remove extra confusing loop variable.
Signed-off-by: NMatt Mackall <mpm@selenic.com>
Acked-by: N"Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Set last allocated object to the object after the one just allocated
before ORing in the extra top bits.  Also handle the case where this
wraps around.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The ib_cm can incorrectly detect a stale connection (a new connection
request for a QPN that is already connected) as a duplicate connection
request.  Separate the handling of potential duplicate REQs from stale
connections.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

commit 518b1646 ("IPoIB/cm: Fix SRQ WR leak") introduced a severe
performance regression on Mellanox cards, because keeping a QP in the
error state for extended periods of time moves hardware to the slow
path (until the QP is destroyed).  For example, MPI latency goes from
~3 usecs to ~7 usecs.

Fix this by posting a send WR on one of the QPs that are being
flushed, instead of using a separate drain QP that is kept in the
error state.

This fixes bug <https://bugs.openfabrics.org/show_bug.cgi?id=636>,
reported and bisected by Scott Weitzenkamp at Cisco and debugged by
Sasha Mikheev at Voltaire.
Signed-off-by: NMichael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

mthca_free_err_wqe() currently treats both send and receive CQEs
identically if a QP is using an SRQ.  But for Tavor hardware, send
CQEs with error can be chained together even if the RQ is part of SRQ,
so we may miss some CQEs.

Fix by following the WQE chain for all send CQEs even for non-SRQ QPs.

This fixes crashes in IPoIB CM:
<https://bugs.openfabrics.org//show_bug.cgi?id=604>
Signed-off-by: NMichael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This patch (as912) replaces a couple of calls to flush_workqueue()
with cancel_sync_work() and cancel_rearming_delayed_work().  Using a
more directed approach allows us to avoid some nasty deadlocks.  The
prime example occurs when a first-level device (the parent is a root
hub) is removed while at the same time the root hub gets a remote
wakeup request.  khubd would try to flush the autosuspend workqueue
while holding the root-hub's lock, and the remote-wakeup workqueue
routine would be waiting to lock the root hub.

The patch also reorganizes the power management portion of
usb_disconnect(), separating it out into its own routine.  The
autosuspend workqueue entry is cancelled immediately instead of
waiting for the device's release routine.  In addition,
synchronization with the autosuspend thread is carried out even for
root hubs (an oversight in the original code).
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg KH <gregkh@suse.de>
Cc: Mark Lord <lkml@rtr.ca>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When hostap_tx_encrypt() tries to allocate enough headroom and
tailroom for ieee80211 encryption, it only makes enough room for the
"mpdu" phase of the operation, but forgets about the "msdu" phase.
(For TKIP, these two phases require, respectively, 4 and 8 bytes of
tailroom, per the "ieee80211_crypt_tkip" structure at the bottom of
net/ieee80211/ieee80211_crypt_tkip.c.)
Signed-off-by: NBrandon Craig Rhodes <brandon@rhodesmill.org>
Signed-off-by: NJouni Malinen <j@w1.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Manually set the device of a skb for prism54 cards that are in monitor
mode as we never call eth_type_trans in that case.
Signed-off-by: NBjörn Steinbrink <B.Steinbrink@gmx.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The DRM code depends on an atomic version of cmpxchg(), which is not
available on sparc32. Since other platforms besides sparc32 have this
issue a KCONFIG option is added for it.
Signed-off-by: NMartin Habets <errandir_news@mph.eclipse.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Linux kernel ignored the PROM's serial settings (115200,n,8,1 in
my case). This was because mode_prop remained "ttyX-mode" (expected:
"ttya-mode") due to the constness of string literals when used with
"char *". Since there is no "ttyX-mode" property in the PROM, Linux
always used the default 9600.

[ Investigation of the suncore.s assembler reveals that gcc optimizied
  away the stores, yet did not emit a warning, which is a pretty
  anti-social thing to do and is the only reason this bug lived for
  so long -DaveM ]
Signed-off-by: NJan Engelhardt <jengelh@gmx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use new esp_scsi for JAZZ SCSI host adapter driver
Signed-off-by: NThomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes section mismatch warnings in the sunzilog driver.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Contributed by Simon Griph.
Signed-off-by: NJeff Garzik <jeff@garzik.org>