The SUGGEST_* flags in the SCSI command result have been out of fashion
for a while and we don't actually use them in the error handling.
Remove the remaining occurrences.
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Enable MSI if available/supported.
Signed-off-by: NWayne Boyer <wayneb@linux.vnet.ibm.com>
Acked-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Fix typo by adding closing parenthesis.
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

(The patch updated based on testing and comments from Tony Battersby.)

Change the sym53c8xx_2 driver negotiation logic so that the driver will
tolerate better device removals. Negotiation message(s) will be sent
with every INQUIRY and REQUEST SENSE command, and whenever there is a
change in goals or when the device reports check condition.

The patch was made specifically to address the case where you hotswap
the disk using remove-single-device/add-single-device commands through
/proc/scsi/scsi. Without the patch the driver keeps using old transfer
parameters even though the target is reset and reports check condition,
so the data transfer of the very first INQUIRY will fail.
Signed-off-by: NAaro Koskinen <Aaro.Koskinen@nokia.com>
Tested-by: NTony Battersby <tonyb@cybernetics.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The Kconfig entry for SCSI_LOGGING refers the reader to
drivers/scsi/scsi.c, but I didn't find any useful information
there. There is certainly logging code in that file, but the
logging types and logging levels are described in
drivers/scsi/scsi_logging.h.

Also, the procfs file referred to in the section is incorrect.
It should be /proc/sys/dev/scsi/logging_level and not
/proc/scsi/scsi.
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NJan Engelhardt <jengelh@medozas.de>
Acked-by: NJames Smart <James.Smart@Emulex.Com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

I got the following warnings on IA64:

drivers/scsi/libfc/fc_lport.c: In function 'fc_lport_recv_flogi_req':
drivers/scsi/libfc/fc_lport.c:788: warning: format '%llx' expects type 'long long unsigned int', but argument 3 has type 'u64'
drivers/scsi/libfc/fc_lport.c:792: warning: format '%llx' expects type 'long long unsigned int', but argument 3 has type 'u64'
scsi/libfc/fc_rport.c: In function 'fc_rport_recv_plogi_req':
/home/fujita/git/linux-2.6/drivers/scsi/libfc/fc_rport.c:968: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'u64'
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Robert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

libfc uses crc32 functions, so cause it to be built
via select:

drivers/built-in.o: In function `fc_frame_crc_check':
(.text+0x75dae): undefined reference to `crc32_le'
drivers/built-in.o: In function `fc_fcp_recv':
fc_fcp.c:(.text+0x7b919): undefined reference to `crc32_le'
fc_fcp.c:(.text+0x7b9d5): undefined reference to `crc32_le'
fc_fcp.c:(.text+0x7ba54): undefined reference to `crc32_le'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Acked-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Fix scsi_debug build error:

drivers/built-in.o: In function `resp_read':
scsi_debug.c:(.text+0x21379a): undefined reference to `crc_t10dif'
drivers/built-in.o: In function `resp_write':
scsi_debug.c:(.text+0x213fca): undefined reference to `crc_t10dif'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

This patch adds support for DIX and DIF in scsi_debug.  A separate
buffer is allocated for the protection information.

 - The dix parameter indicates whether the controller supports DIX
   (protection information DMA)

 - The dif parameter indicates whether the simulated storage device
   supports DIF

 - The guard parameter switches between T10 CRC(0) and IP checksum(1)

 - The ato parameter indicates whether the application tag is owned by
   the disk(0) or the OS(1)

 - DIF and DIX errors can be triggered using the scsi_debug_opts mask
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Acked-by: NDouglas Gilbert <dgilbert@interlog.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Warning(linux-2.6.28-git13//drivers/scsi/scsi_sysfs.c:1049): Excess function parameter 'dev' description in 'scsi_sysfs_add_host'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

SES had its own code to retrieve VPD from devices; convert it to use the
new scsi_get_vpd_page helper.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Based on prior work by Martin Petersen and James Bottomley, this patch
adds a generic helper for retrieving VPD pages from SCSI devices.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The value is already pre-assigned prior to the qla2x00_mem_alloc().
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

QLA_* return codes are 'int' in size.  There were still several
legacy check-points which assumed a return-code width of 8-bits.
This could cause incorrect assumptions of 'good' status if a
return of QLA_FUNCTION_TIMEOUT.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Use minimum value for max vport during firmware initialization in LOOP
topology. Using max vport value from get resource count in LOOP topology
causes firmware initialization failure.
Signed-off-by: NLalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

This change makes the fcoe Rx threads have the same nice value
as lpfc and qla2xxx Rx threads.
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

In fcoe_check_wait_queue() the queue length could temporarily drop to 0,
before the last frame was successfully sent.  This resulted in out of order
data frames within a single sequence, leading to IO timeout errors.

This builds on the approach from Vasu Dev to only fix the queue management in
fcoe_check_wait_queue, where my first patch added locking to the transmit
path even when the pending queue was not in use.

This patch continues to use fcoe_pending_queue.qlen instead of introducing a
new length counter, but takes precautions to ensure it never drops to 0 before
the final frame in the queue has successfully been passed to the netdev qdisc
layer.  It also includes some cleanup of fcoe_check_wait_queue and removes the
fcoe_insert_wait_queue(_head) wrapper functions.
Signed-off-by: NChris Leech <christopher.leech@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

frames followed by these errors in log.

	[sdp] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
	[sdp] Sense Key : Aborted Command [current]
	[sdp] Add. Sense: Data phase error

This was causing some test apps to exit due to write failure under heavy
load.

This was due to a race around adding and removing tx frame skb in
fcoe_pending_queue, Chris Leech helped me to find that brief unlocking
period when pulling skb from fcoe_pending_queue in various contexts
(fcoe_watchdog and fcoe_xmit) and then adding skb back into fcoe_pending_queue
up on a failed fcoe_start_io could change skb/tx frame order in
fcoe_pending_queue. Thanks Chris.

This patch allows only single context to pull skb from fcoe_pending_queue
at any time to prevent above described ordering issue/race by use of
fcoe_pending_queue_active flag.

This patch simplified fcoe_watchdog with modified fcoe_check_wait_queue by
use of FCOE_LOW_QUEUE_DEPTH instead previously used several conditionals
to clear and set lp->qfull.

I think FCOE_MAX_QUEUE_DEPTH with FCOE_LOW_QUEUE_DEPTH  will work better
in re/setting lp->qfull and these could be fine tuned for performance.
Signed-off-by: NVasu Dev <vasu.dev@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Use kfree_skb instead of kfree for struct sk_buff pointers.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

We shouldn't be altering inbound frames.
Signed-off-by: NYi Zou <yi.zou@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The registration function shouldn't initialize the mutex or
list head. The fcoe SW transport should initialize itself
before registering.
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Use helper functions for watchdog timer setup.
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Comment from "Andrew Morton <akpm@linux-foundation.org>"

> +{
> +     return (struct fcoe_softc *)lport_priv(lp);

unneeded/undesirable cast of void*.  There are probably zillions of
instances of this - there always are.

This whole inline function was unnecessary. The FCoE layer knows
that it's data structure is stored in the lport private data, it
can just access it from lport_priv().
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

1) There were a few functions with a strange layout, i.e. all
   arguments on the second line, when not necessary.

   Where ever possible I moved the return value to the same line
   as the function name. However, when the line was too long
   to have a single argument on the same line I moved the
   return value to above line. For example:

   <short return> <function name>(<arg 1>, <arg2>)

   and

   <very long return value>
   <function name>(<arg1>,
		   <arg2>)

2) Removed one extra whitespace line

3) Fixed two typos
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

1) Added '()' for function names in kerneldoc comments

2) Changed comment bookends from '**/' to '*/'. The comment on the the
   mailing list was that '**/' "is consistently unconventional.  Not
   wrong, just odd." The Documentation/kernel-doc-nano-HOWTO.txt
   states that kerneldoc comment blocks should end with '**/' but most
   (if not all) instance I found under drivers/scsi/ were only using
   the '*/' so I converted to that style.

3) Removed incorrect linebreaks in kerneldoc comments where found

4) Removed a few unnecessary blank comment lines in kerneldoc comment
   blocks
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

If we've just created an interface and the an rport is
logging in we may have a request on the wire (say PRLI).
If we destroy the interface, we'll go through each rport
on the disc->rports list and set each rport's state to NONE.
Then the lport will reset the EM. The EM reset will send a
CLOSED event to the prli_resp() handler which will notice
that the state != PRLI. In this case it frees the frame
pointer, decrements the refcount and unlocks the rport.

The problem is that there isn't a frame in this case. It's
just a pointer with an embedded error code. The free causes
an Oops.

This patch moves the error checking to be before the state
checking.
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Just rename the variable as per our naming convention.
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

We only need to use this macro when assigning a value to
rport->dd_data. All other accesses should just use dd_data.
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

When a sequence cannot be delivered to the target, the local
port will schedule retries, While this process is in progress,
if we destroy the FCoE interface, the fcoe_sw_destroy routine is
entered, and the fc_exch_mgr_free(lp->emp) is called.  Thus
if fc_exch_alloc() is called when retrying the sequence,
the mempool_alloc() will fail to allocate the exchange because
the mempool of the exchange manager has already been released.
This patch is to cancel any pending retry work of the local
port before we start to destroy the interface.

Also, when resetting the local port, we should also stop the
scheduled pending retries.
Signed-off-by: NSteve Ma <steve.ma@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The fc_fcp_complete_locked detected data underrun in this case and set
the FC_DATA_UNDRUN but that was ignored by fc_io_compl for all cases
including read underrun.

Added code to not to ignore FC_DATA_UNDRUN for read IO and instead
suggested scsi-ml to retry cmd to  recover from lost data frame.

Not sure if it is okay to ignore FC_DATA_UNDRUN for other case, so let
code as is for other cases but removed or-ing with zero valued fsp->cdb_status
for those cases.
Signed-off-by: NVasu Dev <vasu.dev@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

This allows any rport ELS to retry on LS_RJT.

The rport error handling would only retry on resource allocation failures
and exchange timeouts.  I have a target that will occasionally reject PLOGI
when we do a quick LOGO/PLOGI.  When a critical ELS was rejected, libfc would
fail silently leaving the rport in a dead state.

The retry count and delay are managed by fc_rport_error_retry.  If the retry
count is exceeded fc_rport_error will be called.  When retrying is not the
correct course of action, fc_rport_error can be called directly.
Signed-off-by: NChris Leech <christopher.leech@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The fcoe_xmit could call fc_pause in case the pending skb queue len is larger
than FCOE_MAX_QUEUE_DEPTH, the fc_pause was trying to grab lport->lp_muex to
change lport->link_status and that had these issues :-

1. The fcoe_xmit was getting called with bh disabled, thus causing
"BUG: scheduling while atomic" when grabbing lport->lp_muex with bh disabled.

2. fc_linkup and fc_linkdown function calls lport_enter function with
lport->lp_mutex held and these enter function in turn calls fcoe_xmit to send
lport related FC frame, e.g. fc_linkup => fc_lport_enter_flogi to send flogi
req. In this case grabbing the same lport->lp_mutex again in fc_puase from
fcoe_xmit would cause deadlock.

The lport->lp_mutex was used for setting FC_PAUSE in fcoe_xmit path but
FC_PAUSE bit was not used anywhere beside just setting and clear this
bit in lport->link_status, instead used a separate field qfull in fc_lport
to eliminate need for lport->lp_mutex to track pending queue full condition
and in turn avoid above described two locking issues.

Also added check for lp->qfull in fc_fcp_lport_queue_ready to trigger
SCSI_MLQUEUE_HOST_BUSY when lp->qfull is set to prevent more scsi-ml cmds
while lp->qfull is set.

This patch eliminated FC_LINK_UP and FC_PAUSE and instead used dedicated
fields in fc_lport for this, this simplified all related conditional
code.

Also removed fc_pause and fc_unpause functions and instead used newly added
lport->qfull directly in fcoe.
Signed-off-by: NVasu Dev <vasu.dev@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The fc_seq_start_next grabs ep->ex_lock but this lock was already held here,
so instead called fc_seq_start_next_locked to avoid soft lockup.
Signed-off-by: NVasu Dev <vasu.dev@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Cleanup exchange held due to RRQ when RRQ exch times out, in this case the
ABTS is already done causing RRQ req therefore proceeding with cleanup in
fc_exch_rrq_resp should be okay to restore exch resource.
Signed-off-by: NVasu Dev <vasu.dev@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

When a rport goes away, libFC does a plogi which will reset exchanges
    at the rport. Clean exchanges at our end, both in transport and libFC.
    If transport hooks into exch_mgr_reset, it will call back into
    fc_exch_mgr_reset() to clean up libFC exchanges.
Signed-off-by: NAbhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>