The command to emit batch buffers has changed to address 48b addresses.
It seemed reasonable that we could still use the old instruction where
emitting 0 for length would do the right thing, but it seems to bother
the simulator when the code does that.

Now the second dword in the command has the upper 16b of the address of
the batchbuffer.

v2: Remove duplicated vfun assignment.

v3: Squash in VECS support changes from Zhao Yakui <yakui.zhao@intel.com>

v4: Make checkpatch happy.

Signed-off-by: Ben Widawsky <ben@bwidawsk.net> (v2)
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The interrupt handling implementation remains the same as previous
generations with the 4 types of registers, status, identity, mask, and
enable. However the layout of where the bits go have changed entirely.
To address these changes, all of the interrupt vfuncs needed special
gen8 code.

The way it works is there is a top level status register now which
informs the interrupt service routine which unit caused the interrupt,
and therefore which interrupt registers to read to process the
interrupt. For display the division is quite logical, a set of interrupt
registers for each pipe, and in addition to those, a set each for "misc"
and port.

For GT the things get a bit hairy, as seen by the code. Each of the GT
units has it's own bits defined. They all look *very similar* and
resides in 16 bits of a GT register. As an example, RCS and BCS share
register 0. To compact the code a bit, at a slight expense to
complexity, this is exactly how the code works as well. 2 structures are
added to the ring buffer so that our ring buffer interrupt handling code
knows which ring shares the interrupt registers, and a shift value (ie.
the top or bottom 16 bits of the register).

The above allows us to kept the interrupt register caching scheme, the
per interrupt enables, and the code to mask and unmask interrupts
relatively clean (again at the cost of some more complexity).

Most of the GT units mentioned above are command streamers, and so the
symmetry should work quite well for even the yet to be implemented rings
which Broadwell adds.

v2: Fixes up a couple of bugs, and is more verbose about errors in the
Broadwell interrupt handler.

v3: fix DE_MISC IER offset

v4: Simplify interrupts:
I totally misread the docs the first time I implemented interrupts, and
so this should greatly simplify the mess. Unlike GEN6, we never touch
the regular mask registers in irq_get/put.

v5: Rebased on to of recent pch hotplug setup changes.

v6: Fixup on top of moving num_pipes to intel_info.

v7: Rebased on top of Egbert Eich's hpd irq handling rework. Also
wired up ibx_hpd_irq_setup for gen8.

v8: Rebase on top of Jani's asle handling rework.

v9: Rebase on top of Ben's VECS enabling for Haswell, where he
unfortunately went OCD on the gt irq #defines. Not that they're still
not yet fully consistent:
- Used the GT_RENDER_ #defines + bdw shifts.
- Dropped the shift from the L3_PARITY stuff, seemed clearer.
- s/irq_refcount/irq_refcount.gt/

v10: Squash in VECS enabling patches and the gen8_gt_irq_handler
refactoring from Zhao Yakui <yakui.zhao@intel.com>

v11: Rebase on top of the interrupt cleanups in upstream.

v12: Rebase on top of Ben's DPF changes in upstream.

v13: Drop bdw from the HAS_L3_DPF feature flag for now, it's unclear what
exactly needs to be done. Requested by Ben.

v14: Fix the patch.
- Drop the mask of reserved bits and assorted logic, it doesn't match
  the spec.
- Do the posting read inconditionally instead of commenting it out.
- Add a GEN8_MASTER_IRQ_CONTROL definition and use it.
- Fix up the GEN8_PIPE interrupt defines and give the GEN8_ prefixes -
  we actually will need to use them.
- Enclose macros in do {} while (0) (checkpatch).
- Clear DE_MISC interrupt bits only after having processed them.
- Fix whitespace fail (checkpatch).
- Fix overtly long lines where appropriate (checkpatch).
- Don't use typedef'ed private_t (maintainer-scripts).
- Align the function parameter list correctly.

Signed-off-by: Ben Widawsky <ben@bwidawsk.net> (v4)
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

bikeshed

Just enough to make the code not barf...

Init BDW display to look like HSW. For the simulator this should be
fine, but this will probably require more work.
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
[danvet: Add a FIXME comment about RCS flips being untested on bdw.
Also add a note that hblank events are reserved on bdw+ in DERRMR.]
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

BDW context sizes varies a bit.

v2: Squash in fixup for the hw context size from Ben.

Signed-off-by: Ben Widawsky <ben@bwidawsk.net> (v1)
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We need to reset the DP scrambler on every vsync to get stable CRCs.
And since we can't use the normal pipe CRC on DP ports on g4x we
really need them to be able to test modesetting issues on (e)DP
outputs.

Note that the DC balance reset is for SDVO port CRCs so we don't
strictly need it. But better safe than sorry (and it's a nice template
in case we ever want to grab port CRCs for e.g. audio checking).

v2: Apply the suggestions from Damien's review.
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Incorrect definition DPIO_TX3_SWING_CTL4.

From Ville's review: "Based on the specs, the typo meant that HDMI B
ended up using "incorrect" de-emphasis for the TMDS data lanes."
Signed-off-by: NChon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Add comment from Ville's review about the impact.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

- Use a for_each_loop and add the corresponding #defines.
- Drop the _ILK postfix on the existing DE_PIPE_VBLANK macro for
  consistency with everything else.
- Also use macros (and add the missing one for plane flips) for the
  ivb display interrupt handler.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Drop the useless parens that Ville spotted.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The bbstate contains useful bits of debugging information such as
whether the batch is being read from GTT or PPGTT, or whether it is
allowed to execute privileged instructions.

v2: Only record BB_STATE for gen4+
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Production HSW does not need it. I confirmed this with Art.
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

All our registers which are written through the MCHBAR are defined
descriptively as an offset to the MCHBAR. We had 3 outliers here.
Convert these as well so all registers which are offsets are MCHBAR can
be easily identified/found within the code.

With this, convert DCLK to also follow this format.
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Really simple, and we don't even have working frame numbers.

v2: Actually enable it ...

v3: Review from Ville:
- Unconditionally enable the border in the CRC checksum for
  consistency with gen3+.
- Handle the "none" source to be able to disable the CRC machinery
  again.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The PIPE_B #define was missing the display mmio offset. Use the
_PIPE_INC macro instead, it's simpler.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

A bit a mess, since with DP/TV outputs we can't use the pipe CRC.
Also, no plane CRCs, so we need to update the basic testcases.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Should work down to gen2. The #defines for the interrupt sources are
already there in PIPESTAT and are the same on all gmch platforms for
gen2 up to vlv.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Once the machine gets to a certain point in the suspend process, we
expect the GPU to be idle. If it is not, we might corrupt memory.
Empirically (with an early version of this patch) we have seen this is
not the case. We cannot currently explain why the latent GPU writes
occur.

In the technical sense, this patch is a workaround in that we have an
issue we can't explain, and the patch indirectly solves the issue.
However, it's really better than a workaround because we understand why
it works, and it really should be a safe thing to do in all cases.

The noticeable effect other than the debug messages would be an increase
in the suspend time. I have not measure how expensive it actually is.

I think it would be good to spend further time to root cause why we're
seeing these latent writes, but it shouldn't preclude preventing the
fallout.

NOTE: It should be safe (and makes some sense IMO) to also keep the
VALID bit unset on resume when we clear_range(). I've opted not to do
this as properly clearing those bits at some later point would be extra
work.

v2: Fix bugzilla link

Bugzilla: http://bugs.freedesktop.org/show_bug.cgi?id=65496
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=59321Tested-by: NTakashi Iwai <tiwai@suse.de>
Tested-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Tested-By: NTodd Previte <tprevite@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

hw designers decided to change the CRC registers and coalesce them all
into one. Otherwise nothing changed. I've opted for a new hsw_ version
to grab the crc sample since hsw+1 will have the same crc registers,
but different interrupt source registers. So this little helper
function will come handy there.

Also refactor the display error handler with a neat pipe loop.

v2: Use for_each_pipe.
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We enable the interrupt unconditionally and only control it
through the enable bit in the CRC control register.

v2: Extract per-platform helpers to compute the register values.
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Also add a new _PIPE_INC macro which takes an base plus increment.
Much less likely to botch the job by missing an s/A/B/ somewhere.

v2: They've moved the bitfield. Argh!
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The HDMI audio expects HDMI pixel clock to be set in the audio
configuration. We've currently just set 0, using 25.2 / 1.001 kHz
frequency, which fails with some modes.

v2: Now with a commit message.

Reference: http://mid.gmane.org/CAGpEb3Ep1LRZETPxHGRfBDqr5Ts2tAc8gCukWwugUf1U5NYv1g@mail.gmail.com
Reference: http://mid.gmane.org/20130206213533.GA16367@hardeman.nuReported-by: NDavid Härdeman <david@hardeman.nu>
Reported-by: NJasper Smet <josbeir@gmail.com>
Tested-by: NJasper Smet <josbeir@gmail.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

There are several points in the display pipeline where CRCs can be
computed on the bits flowing there. For instance, it's usually possible
to compute the CRCs of the primary plane, the sprite plane or the CRCs
of the bits after the panel fitter (collectively called pipe CRCs).

v2: Quite a bit of rework here and there (Damien)
Signed-off-by: NShuang He <shuang.he@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
[danvet: Fix intermediate compile file reported by Wu Fengguang's
kernel builder.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We want to be able to use the masks to decode the register contents
regardless of the hardware generation. So just expand the masks to
cover all available bits, even if those are reserved on some
generations.

v2: Don't extend WM1_LP_SR_MASK so far, for the *future*
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Needed to prevent display corruption in high res panels.

v2: use correct unit names (Rodrigo)
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: NUlrich Drepper <drepper@gmail.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Supposedly VLV uses the CTG+ style frame counter registers instead of
the old gen3/4 style. Add the magic offset to the correct registers.

We should already be taking the correct codepaths for
.get_vblank_counter() and .get_scanout_position().
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

During system boot up, by default, the power gate for render, media and
display well still power gated.  Normally, BIOS will turn off the power
gate.  In the BIOS-less system, the driver need to turn off the power
gate very early during driver load.

v2: Move this to intel_uncore_sanitize to allow it to get call during
resume path. (Daniel)
v3: Remove redundant write 0 to DPIO_CTL, and use DPIO_RESET instead of
just 0x1 (Ville)
    Add turn of power gate for display 2d/render well/media well.
v4: Remove toggle cmnreset in intel_uncore_sanitize.  Cmnreset should
toggle after CRI clock source has been selected.  Jesse DPIO reset patch
which toggle the cmnreset in intel_modeset_init_hw() should handle it.
(Ville)
Signed-off-by: NChon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

DPIO needs to have common reset de-asserted on soft resets like boot and
S3.  In some cases, the BIOS will have done this for us, but it should
be safe to do at runtime as well, as long as we do it when the pipes are
otherwise off.

v2: update bit name to match docs better (Ville)
    reset after CRI clock select (Ville)

References: https://bugs.freedesktop.org/show_bug.cgi?id=69166Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

After applying wait-boost we often find ourselves stuck at higher clocks
than required. The current threshold value requires the GPU to be
continuously and completely idle for 313ms before it is dropped by one
bin. Conversely, we require the GPU to be busy for an average of 90% over
a 84ms period before we upclock. So the current thresholds almost never
downclock the GPU, and respond very slowly to sudden demands for more
power. It is easy to observe that we currently lock into the wrong bin
and both underperform in benchmarks and consume more power than optimal
(just by repeating the task and measuring the different results).

An alternative approach, as discussed in the bspec, is to use a
continuous threshold for upclocking, and an average value for downclocking.
This is good for quickly detecting and reacting to state changes within a
frame, however it fails with the common throttling method of waiting
upon the outstanding frame - at least it is difficult to choose a
threshold that works well at 15,000fps and at 60fps. So continue to use
average busy/idle loads to determine frequency change.

v2: Use 3 power zones to keep frequencies low in steady-state mostly
idle (e.g. scrolling, interactive 2D drawing), and frequencies high
for demanding games. In between those end-states, we use a
fast-reclocking algorithm to converge more quickly on the desired bin.

v3: Bug fixes - make sure we reset adj after switching power zones.

v4: Tune - drop the continuous busy thresholds as it prevents us from
choosing the right frequency for glxgears style swap benchmarks. Instead
the goal is to be able to find the right clocks irrespective of the
wait-boost.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Kenneth Graunke <kenneth@whitecape.org>
Cc: Stéphane Marchesin <stephane.marchesin@gmail.com>
Cc: Owen Taylor <otaylor@redhat.com>
Cc: "Meng, Mengmeng" <mengmeng.meng@intel.com>
Cc: "Zhuang, Lena" <lena.zhuang@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Otherwise using any atomic memory operation will lock up the GPU due
to a Haswell hardware bug.

v2: Use the _MASKED_BIT_ENABLE macro.  Drop drm parameter definition.
Signed-off-by: NFrancisco Jerez <currojerez@riseup.net>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: <stable@vger.kernel.org>
[danvet: Fix checkpatch fail.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We need to use the clock control reg to figure out how many CZ clks are in
30ns and use that as the basis for our RC6 residency calculations.

v2: use ULL everywhere for consistency (Chris)
    factor out bias for clarity (Chris)

References: https://bugs.freedesktop.org/show_bug.cgi?id=69692Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

And add some reg defines while we're at it.  Since the units of the RC6
residency counter are actually in CZ clocks, we want to just use the
high bits or we'll overflow too frequently.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

CDCLK is used to generate the gmbus clock.  This is normally done by
BIOS. Program the value if the BIOS-less system doesn't do it.

v2: Move this to intel_i2c_reset to allow reprogram the gmbus frequency
during resume. (Daniel)

v3: Change GMBUS_FREQ to GMBUSFREQ_VLV, and use VLV_DISPLAY_BASE.
(Ville).
	Remove cdclk_ratio[] table, and calculate the cdclk ratio instead.
(Ville).
 	Change the shift then mask for reg read, to mask first, then shift.
(Ville).
	Remove the gmbus frequency calculation = cdclk/1.01.  Based on BIOS
programming, gmbus frequency = cdclk frequency. (Ville)
	Add get_disp_clk_div, which can use to get cdclk/czclk divide.

v4: Fix the mmio_offset base for CZCLK_CDCLK_FREQ_RATIO, gmbus_freq
calculation, and duplicate check for gmbus_freq. (Ville)

In VLV, the spec is wrong about 4Mhz reference frequency for GMBUS. It
should be 1Mhz.
Signed-off-by: NChon Ming Lee <chon.ming.lee@intel.com>
[danvet: Add the comment Ville suggested. Also appease checkpatch a
bit.]
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The | operation has higher precedence than "?:" so the macro always
returns GT_RENDER_L3_PARITY_ERROR_INTERRUPT_S1.

This regression has been introduce in "drm/i915: Add second slice l3
remapping".
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Future generations will be changing these registers (thanks to design
for giving us an early heads up). To help abstract, create the
definition of the base of the register block, and define all registers
relative to that.

Design has promised to not change the offsets relative to the base.

v2: Also change IS_HASWELL checks to HAS_PSR

CC: Rodrigo Vivi <rodrigo.vivi@gmail.com>
CC: Intel GFX <intel-gfx@lists.freedesktop.org>
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Certain HSW SKUs have a second bank of L3. This L3 remapping has a
separate register set, and interrupt from the first "slice". A slice is
simply a term to define some subset of the GPU's l3 cache. This patch
implements both the interrupt handler, and ability to communicate with
userspace about this second slice.

v2:  Remove redundant check about non-existent slice.
Change warning about interrupts of unknown slices to WARN_ON_ONCE
Handle the case where we get 2 slice interrupts concurrently, and switch
the tracking of interrupts to be non-destructive (all Ville)
Don't enable/mask the second slice parity interrupt for ivb/vlv (even
though all docs I can find claim it's rsvd) (Ville + Bryan)
Keep BYT excluded from L3 parity

v3: Fix the slice = ffs to be decremented by one (found by Ville). When
I initially did my testing on the series, I was using 1-based slice
counting, so this code was correct. Not sure why my simpler tests that
I've been running since then didn't pick it up sooner.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

You can't write it using the MCHBAR mirror, the write will just get
dropped.

This should make us BSpec-compliant, but there's no real bug I could
reproduce that is fixed by this patch.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
[danvet: Fix spelling mistake in the comment that Damien spotted.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Now that adjusted_mode.clock no longer contains the pixel_multiplier, we
can kill the get_clock() callback and instead do the clock readout
in get_pipe_config().

Also i9xx_crtc_clock_get() can now extract the frequency of the PCH
DPLL, so use it to populate port_clock accurately for PCH encoders.
For DP in port A the encoder is still responsible for filling in
port_clock. The FDI adjusted_mode.clock extraction is kept in place
for some extra sanity checking, but we no longer need to pretend it's
also the port_clock.

In the encoder get_config() functions fill out adjusted_mode.clock
based on port_clock and other details such as the DP M/N values,
HDMI 12bpc and SDVO pixel_multiplier. For PCH encoders we will then
do an extra sanity check to make sure the dotclock we derived from
the FDI configuratiuon matches the one we derive from port_clock.

DVO doesn't exist on PCH platforms, so it doesn't need to anything
but assign adjusted_mode.clock=port_clock. And DDI is HSW only, so
none of the changes apply there.

v2: Use hdmi_reg color format to detect 12bpc HDMI case
v3: Set adjusted_mode.clock for LVDS too
v4: Rename ironlake_crtc_clock_get to ironlake_pch_clock_get,
    eliminate the useless link_freq variable.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Remove duplicates, add VLV specific macros for port B and C.

v2: also add PANEL_PORT_SELECT_DPC_VLV for clarity (Ville)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Batchbuffers constructed by userspace can conditionalise their URB
allocations through the use of the MI_SET_PREDICATE command. This
command can read the MI_PREDICATE_RESULT_2 register to see how many
slices are enabled on GT3, and by virtue of the result, scale their
memory allocations to fit enabled memory.

Of course, this only works if the kernel sets the appropriate bit in the
register first.

v2: Better commit subject and message by Chris Wilson.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Credits-to: Yejun Guo <yejun.guo@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

v2:
 - Grab dpio_lock mutex in vlv_enable_dsi_pll().
 - Add and call vlv_disable_dsi_pll().

v3: Mostly based on Ville's review comments.
 - Only pipe A has DSI PLL lock bit.
 - Add more of CCK REG bit definitions for DSI PLL.
 - Make tables static.
 - Move clock gating out of the clock calculation functions.
 - DSI PLL LDO power gating.
 - Put alternative MNP from table calc behind #ifdef.

v4: s/CKK/CLK/ in the CCK REG bit definitions (Ville).
Signed-off-by: Nymohanma <yogesh.mohan.marimuthu@intel.com>
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Add definitions for VLV MIPI DSI registers.

v2: Small fixes per Ville's review comments.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>