This patch tackles one of the problems of my
reorder release timer patch from August.

<http://www.spinics.net/lists/linux-wireless/msg57214.html>
=>
What if the reorder release triggers and ap_sta_ps_end
(called by ieee80211_rx_h_sta_process) accidentally clears
the WLAN_STA_PS_STA flag, because 100ms ago - when the STA
was still active - frames were put into the reorder buffer.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Does not allow any channel different of HCI_CHANNEL_RAW and
HCI_CHANNEL_CONTROL to bind.
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

The initialization function used by hci_open_dev (hci_init_req) sends
many different HCI commands. The __hci_request function should only
return when all of these commands have completed (or a timeout occurs).
Several of these commands cause hci_req_complete to be called which
causes __hci_request to return prematurely.

This patch fixes the issue by adding a new hdev->req_last_cmd variable
which is set during the initialization procedure. The hci_req_complete
function will no longer mark the request as complete until the command
matching hdev->req_last_cmd completes.
Signed-off-by: NJohan Hedberg <johan.hedberg@nokia.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

This patch adds Bluetooth Management interface events for controller
addition and removal. The events correspond to the existing HCI_DEV_REG
and HCI_DEV_UNREG stack internal events.
Signed-off-by: NJohan Hedberg <johan.hedberg@nokia.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

This patch implements the read_info command which is used to fetch basic
info about an adapter.
Signed-off-by: NJohan Hedberg <johan.hedberg@nokia.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

This patch implements the read_index_list command through which
userspace can get a list of current adapter indices.
Signed-off-by: NJohan Hedberg <johan.hedberg@nokia.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

This patch implements the initial read_version command that userspace
will use before any other management interface operations.
Signed-off-by: NJohan Hedberg <johan.hedberg@nokia.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

The command handlers for bluetooth management messaging should be able
to report errors (such as memory allocation failures) to the higher
levels in the call stack.
Signed-off-by: NJohan Hedberg <johan.hedberg@nokia.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

There's a redundant rcu_read_lock/unlock pair, a
redundant variable, and a few redundant accesses
to the 1d_to_ac array. Fix this to make the code
neater and easier to follow.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When an skb is shared, it needs to be duplicated, along with its data buffer.
If the skb does not have enough headroom, using skb_copy might cause the data
buffer to be copied twice (once by skb_copy and once by pskb_expand_head).
Fix this by using skb_clone initially and letting ieee80211_skb_resize sort
out the rest.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If the skb is not cloned and we don't need any extra headroom, there
is no point in reallocating the skb head.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The change 'mac80211: Fix BUG in pskb_expand_head when transmitting shared skbs'
added a check for copying the skb if it's shared, however the tx info variable
still points at the cb of the old skb
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The Mesh Control header only includes 0, 1 or 2 addresses. If there is
one address, it should be interpreted as Address 4.  If there are 2,
they are interpreted as Addresses 5 and 6 (Address 4 being the 4th
address in the 802.11 header).

The address extension used to hold up to 3 addresses instead of the current 2.
I'm not sure which draft version changed this, but it is very unlikely that it
will change again given the state of the approval process of this draft.  See
section 7.1.3.6.3 in current draft (8.0).

Also, note that the extra address that I'm removing was not being used, so this
change has no effect on over-the-air frame formats.  But I thought I better
remove it before someone does start using it.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Export the information which antennas are available for configuration as TX or
RX antennas via nl80211.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As has been pointed out by Daniel Halperin some devices (e.g. Intel IWL5100)
can only TX from a subset of RX antennas, so use separate availability masks
for RX and TX.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Let path selection frames for protocols other than HWMP be sent to
userspace via NL80211_CMD_REGISTER_FRAME.  Also allow userspace to send
and receive mesh path selection frames.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Userspace will now be allowed to toggle between the default path
selection algorithm (HWMP, implemented in the kernel), and a vendor
specific alternative.  Also in the same patch, allow userspace to add
information elements to mesh beacons.  This is accordance with the
Extensible Path Selection Framework specified in version 7.0 of the
802.11s draft.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Mesh parameters can be to setup a mesh or to configure it.
This patch renames the ambiguous name mesh_params to mesh_config
in preparation for mesh_setup.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Once we moved the core regulatory request to the queue and let
the scheduler process it last_request will have been left NULL
until the schedular decides to process the first request. When
this happens and we are loading a driver with a custom regulatory
request like all Atheros drivers we end up with a NULL pointer
dereference. We fix this by checking if the request was a
custom one.

BUG: unable to handle kernel NULL pointer dereference at 0000000000000004
IP: [<ffffffffa016de87>] freq_reg_info_regd.clone.2+0x27/0x130 [cfg80211]
PGD 71f91067 PUD 712b2067 PMD 0
Oops: 0000 [#1] PREEMPT SMP
last sysfs file: /sys/devices/pci0000:00/0000:00:1d.7/usb2/2-1/firmware/2-1/loading
CPU 0
Modules linked in: ath9k_htc(+) ath9k_common ath9k_hw ath <etc>
Pid: 3094, comm: insmod Tainted: G        W   2.6.37-rc5-wl #16 INVALID/28427ZQ
RIP: 0010:[<ffffffffa016de87>]  [<ffffffffa016de87>] freq_reg_info_regd.clone.2+0x27/0x130 [cfg80211]
RSP: 0018:ffff88007045db78  EFLAGS: 00010282
RAX: 0000000000000000 RBX: ffffffffa047d9a0 RCX: ffff88007045dbd0
RDX: 0000000000004e20 RSI: 000000000024cde0 RDI: ffff8800700483e0
RBP: ffff88007045db98 R08: ffffffffa02f5b40 R09: 0000000000000001
R10: 000000000000000e R11: 0000000000000001 R12: 0000000000000000
R13: ffff88007004e3b0 R14: 0000000000000000 R15: ffff880070048340
FS:  00007f635a707700(0000) GS:ffff880077400000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000004 CR3: 00000000708a9000 CR4: 00000000000006f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process insmod (pid: 3094, threadinfo ffff88007045c000, task ffff8800713e3ec0)
Stack:
 ffffffffa047d9a0 0000000000000000 ffff88007004e3b0 0000000000000000
 ffff88007045dc08 ffffffffa016e147 000000007045dc08 0000000000000002
 ffff8800700483e0 ffffffffa02f5b40 ffff88007045dbd8 0000000000000000
Call Trace:
 [<ffffffffa016e147>] wiphy_apply_custom_regulatory+0x137/0x1d0 [cfg80211]
 [<ffffffffa047a690>] ? ath9k_reg_notifier+0x0/0x50 [ath9k_htc]
 [<ffffffffa02f47f7>] ath_regd_init+0x347/0x430 [ath]
 [<ffffffffa047b1f5>] ath9k_htc_probe_device+0x6c5/0x960 [ath9k_htc]
 [<ffffffffa0472a2c>] ath9k_htc_hw_init+0xc/0x30 [ath9k_htc]
 [<ffffffffa04747e6>] ath9k_hif_usb_probe+0x216/0x3b0 [ath9k_htc]
 [<ffffffffa03bb6bc>] usb_probe_interface+0x10c/0x210 [usbcore]
 [<ffffffff812aec26>] driver_probe_device+0x96/0x1c0
 [<ffffffff812aedf3>] __driver_attach+0xa3/0xb0
 [<ffffffff812aed50>] ? __driver_attach+0x0/0xb0
 [<ffffffff812adaae>] bus_for_each_dev+0x5e/0x90
 [<ffffffff812ae8c9>] driver_attach+0x19/0x20
 [<ffffffff812ae438>] bus_add_driver+0x168/0x320
 [<ffffffff812af071>] driver_register+0x71/0x140
 [<ffffffff811fc4a8>] ? __raw_spin_lock_init+0x38/0x70
 [<ffffffffa03ba39c>] usb_register_driver+0xdc/0x190 [usbcore]
 [<ffffffffa03a2000>] ? ath9k_htc_init+0x0/0x4f [ath9k_htc]
 [<ffffffffa047499e>] ath9k_hif_usb_init+0x1e/0x20 [ath9k_htc]
 [<ffffffffa03a202b>] ath9k_htc_init+0x2b/0x4f [ath9k_htc]
 [<ffffffff8100212f>] do_one_initcall+0x3f/0x180
 [<ffffffff8109ef5b>] sys_init_module+0xbb/0x200
 [<ffffffff8100bf52>] system_call_fastpath+0x16/0x1b
Code: <etc, who cares>
RIP  [<ffffffffa016de87>] freq_reg_info_regd.clone.2+0x27/0x130 [cfg80211]
 RSP <ffff88007045db78>
CR2: 0000000000000004
---[ end trace 79e4193601c8b713 ]---
Reported-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add a new notification to indicate that a received, unprotected
Deauthentication or Disassociation frame was dropped due to
management frame protection being in use. This notification is
needed to allow user space (e.g., wpa_supplicant) to implement
SA Query procedure to recover from association state mismatch
between an AP and STA.

This is needed to avoid getting stuck in non-working state when MFP
(IEEE 802.11w) is used and a protected Deauthentication or
Disassociation frame is dropped for any reason. After that, the
station would silently discard any unprotected Deauthentication or
Disassociation frame that could be indicating that the AP does not
have association for the STA (when the Reason Code would be 6 or 7).
IEEE Std 802.11w-2009, 11.13 describes this recovery mechanism.
Signed-off-by: NJouni Malinen <j@w1.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Commit 00d3f14c has removed the references of this macro,
but left it only. So remove this definition.

commit 00d3f14c
Author: Johannes Berg <johannes@sipsolutions.net>
Date:   Tue Feb 10 21:26:00 2009 +0100

    mac80211: use cfg80211s BSS infrastructure

    Remove all the code from mac80211 to keep track of BSSes
    and use the cfg80211-provided code completely.
Signed-off-by: NShan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Allow drivers or rate control algorithms to specify BlockAck session
timeout when initiating an ADDBA transaction. This is useful in cases
where maintaining persistent BA sessions does not incur any overhead.

The current timeout value of 5000 TUs is retained for all non ath9k/ath9k_htc
drivers.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Reviewed-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With the upcoming hardware offload implementation,
some devices will have a different maximum duration
for the remain-on-channel command. Advertise the
maximum duration in mac80211, and make mac80211 set
it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When software crypto is used, mac80211 will
support IBSS RSN, it doesn't depend on the
driver in that case.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The 802.11 spec states that the STA that generated the last Beacon frame shall
be the STA that response to a probe request.  This is important for congestion
reduction when a probe request is received - only 1 node in an adhoc BSS
will transmit a response.  While mac80211 drivers should provide the
tx_last_beacon function to report if they transmitted the last beacon many
do not.  As an attempt to reduce probe response congestion default this
to 0 such that a node not implementing this capability does not contribute
to unnecessary congestion.

In a modern medium sized office environment I see upwards of 100 probe
requests per second received at a given node from various hardware/OS/drivers
doing zeroconf 'active probing' as opposed to passively listening for beacons.
With a modest 10-node adhoc network consisting of drivers that do not implement
this tx_last_beacon feature, I have seen this result in the simultaneous xmit
of probe responses accumulating to 500 probe responses per second because of
collisions which brings the adhoc network to its knees as well as causes
needless congestion.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add support for split default keys (unicast
and multicast) in mac80211.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Allow userspace to specify that a given key
is default only for unicast and/or multicast
transmissions. Only WEP keys are for both,
WPA/RSN keys set here are GTKs for multicast
only. For more future flexibility, allow to
specify all combiations.

Wireless extensions can only set both so use
nl80211; WEP keys (connect keys) must be set
as default for both (but 802.1X WEP is still
possible).
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Using the default key for "any key set" isn't
quite what we should do. It works, but with the
upcoming changes it makes life unnecessarily
complex, so do something better here and really
check for "any key".
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When a cached BSS struct is updated because a new beacon was received,
the code replaces the cached information elements by the IEs from the
new beacon. However it did not update the pub.information_elements
and pub.len_information_elements fields leaving them either pointing
to the old beacon IEs or in an inconsistent state where the data is
replaced by the new beacon IEs but len_information_elements still has
its value from the first beacon.

Fix this by updating the information elements fields if they are
pointing to beacon IEs.
Signed-off-by: NSven Neumann <s.neumann@raumfeld.com>
Reviewed-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add a field to wiphy for the hardware to report the availble antennas for
configuration. Only if this is set to something bigger than zero, will the
anntenna configuration ops be executed.

Allthough this could be a simple number of antennas, I defined it as a bitmap
of antennas which are available for configuration, since it's more consistent
with the rest of the antenna API and there could be cases where the
hardware allows only configuration of certain antennas. As it does not make
much of a difference in size or normal usage, I think it's better to be able to
support this, in case the need arises.

The antenna configuration is now also checked against the availabe antennas and
rejected if it does not match.
Signed-off-by: NBruno Randolf <br1@einfach.org>

--
v3:	always apply available antenna mask (for "all" antennas case).

v2:	reject antenna configurations which don't match the available antennas
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On suspend, there might be usb wireless drivers which wrongly trigger
the warning in ieee80211_work_work. If an usb driver doesn't have a
suspend hook, the usb stack will disconnect the device. On disconnect,
a mac80211 driver calls ieee80211_unregister_hw, which calls dev_close,
which calls ieee80211_stop, and in the end calls ieee80211_work_purge->
ieee80211_work_work.

The problem is that this call to ieee80211_work_purge comes after
mac80211 is suspended, triggering the warning even when we don't have
work queued in work_list (the expected case when already suspended),
because it always calls ieee80211_work_work.

So, just call ieee80211_work_work in ieee80211_work_purge if we really
have to abort work. This addresses the warning reported at
https://bugzilla.kernel.org/show_bug.cgi?id=24402Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

dev_open will eventually call ieee80211_ibss_join which sets up the
skb used for beacons/probe-responses however it is possible to
receive beacons that attempt to merge before this occurs causing
a null pointer dereference.  Check ssid_len as that is the last
thing set in ieee80211_ibss_join.

This occurs quite easily in the presence of adhoc nodes with hidden SSID's

revised previous patch to check further up based on irc feedback
Signed-off-by: NTim Harvey <harvey.tim@gmail.com>
Reviewed-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add a new BSS attribute to allow hostapd to set the current HT opmode.
Otherwise drivers won't be able to set up protection for HT rates in
AP mode.

Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

mac80211 doesn't handle shared skbs correctly at the moment. As a result
a possible resize can trigger a BUG in pskb_expand_head.

[  676.030000] Kernel bug detected[#1]:
[  676.030000] Cpu 0
[  676.030000] $ 0   : 00000000 00000000 819662ff 00000002
[  676.030000] $ 4   : 81966200 00000020 00000000 00000020
[  676.030000] $ 8   : 819662e0 800043c0 00000002 00020000
[  676.030000] $12   : 3b9aca00 00000000 00000000 00470000
[  676.030000] $16   : 80ea2000 00000000 00000000 00000000
[  676.030000] $20   : 818aa200 80ea2018 80ea2000 00000008
[  676.030000] $24   : 00000002 800ace5c
[  676.030000] $28   : 8199a000 8199bd20 81938f88 80f180d4
[  676.030000] Hi    : 0000026e
[  676.030000] Lo    : 0000757e
[  676.030000] epc   : 801245e4 pskb_expand_head+0x44/0x1d8
[  676.030000]     Not tainted
[  676.030000] ra    : 80f180d4 ieee80211_skb_resize+0xb0/0x114 [mac80211]
[  676.030000] Status: 1000a403    KERNEL EXL IE
[  676.030000] Cause : 10800024
[  676.030000] PrId  : 0001964c (MIPS 24Kc)
[  676.030000] Modules linked in: mac80211_hwsim rt2800lib rt2x00soc rt2x00pci rt2x00lib mac80211 crc_itu_t crc_ccitt cfg80211 compat arc4 aes_generic deflate ecb cbc [last unloaded: rt2800pci]
[  676.030000] Process kpktgend_0 (pid: 97, threadinfo=8199a000, task=81879f48, tls=00000000)
[  676.030000] Stack : ffffffff 00000000 00000000 00000014 00000004 80ea2000 00000000 00000000
[  676.030000]         818aa200 80f180d4 ffffffff 0000000a 81879f78 81879f48 81879f48 00000018
[  676.030000]         81966246 80ea2000 818432e0 80f1a420 80203050 81814d98 00000001 81879f48
[  676.030000]         81879f48 00000018 81966246 818432e0 0000001a 8199bdd4 0000001c 80f1b72c
[  676.030000]         80203020 8001292c 80ef4aa2 7f10b55d 801ab5b8 81879f48 00000188 80005c90
[  676.030000]         ...
[  676.030000] Call Trace:
[  676.030000] [<801245e4>] pskb_expand_head+0x44/0x1d8
[  676.030000] [<80f180d4>] ieee80211_skb_resize+0xb0/0x114 [mac80211]
[  676.030000] [<80f1a420>] ieee80211_xmit+0x150/0x22c [mac80211]
[  676.030000] [<80f1b72c>] ieee80211_subif_start_xmit+0x6f4/0x73c [mac80211]
[  676.030000] [<8014361c>] pktgen_thread_worker+0xfac/0x16f8
[  676.030000] [<8002ebe8>] kthread+0x7c/0x88
[  676.030000] [<80008e0c>] kernel_thread_helper+0x10/0x18
[  676.030000]
[  676.030000]
[  676.030000] Code: 24020001  10620005  2502001f <0200000d> 0804917a  00000000  2502001f  00441023  00531021

Fix this by making a local copy of shared skbs prior to mangeling them.
To avoid copying the skb unnecessarily move the skb_copy call below the
checks that don't need write access to the skb.

Also, move the assignment of nh_pos and h_pos below the skb_copy to point
to the correct skb.

It would be possible to avoid another resize of the copied skb by using
skb_copy_expand instead of skb_copy but that would make the patch more
complex. Also, shared skbs are a corner case right now, so the resize
shouldn't matter much.

Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In order to send data to management control sockets the function should:

  - skip checks intended for raw HCI data and stack internal events
  - make sure RAW HCI data or stack internal events don't go to
    management control sockets

In order to accomplish this the patch adds a new member to the bluetooth
skb private data to flag skb's that are destined for management control
sockets.
Signed-off-by: NJohan Hedberg <johan.hedberg@nokia.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

Add initial code for handling Bluetooth Management interface messages.
Signed-off-by: NJohan Hedberg <johan.hedberg@nokia.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Acked-by: NAndrei Emeltchenko <andrei.emeltchenko@nokia.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

Wrap mesh sections inside CONFIG_MAC80211_MESH to fix compilation
problems reported by Stephen Rothwell, Larry Finger and Bruno Randolf.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

net/mac80211/mlme.c: In function 'ieee80211_sta_work':
net/mac80211/mlme.c:1981: warning: too many arguments for format

Introduced by commit 04ac3c0e
("mac80211: speed up AP probing using nullfunc frames").
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>